논문 상세보기

복합소재 선체 외판의 초음파 탐상을 위한 탐촉자 주파수와 수신기 음향 속력의 상관관계 KCI 등재

Correlation between Probe Frequency and Echo-Pulse Velocity for Ultrasonic Testing of a Fiber-Reinforced Plastic Hull Plate

  • 언어KOR
  • URLhttps://db.koreascholar.com/Article/Detail/390755
구독 기관 인증 시 무료 이용이 가능합니다. 4,000원
해양환경안전학회지 (Journal of the Korean Society of Marine Environment and Safety)
해양환경안전학회 (The Korean Society Of Marine Environment & Safety)
초록

선체구조의 품질검사 중 가장 일반적인 방법의 하나는 비파괴검사이다. 하지만 복합소재 선체는 강화재와 수지로 구성된 여러가지 재료가 섞여 있고 또 생산환경과 작업자에 따라 FRP(Fiber-Reinforced Plastics) 제작품질에 차이가 발생할 가능성이 크기 때문에 정확한 검사평가는 쉽지 않은 일이다. 특히 FRP 선박의 경우에는 다른 구조물보다 두께가 매우 두껍고 주로 수척층 공법을 이용하기 때문에 더욱 그렇다. 초음파 탐상의 조건 중 검사체의 밀도가 매우 중요하기 때문에 본 연구에서는 FRP 선박 제작에 널리 사용되고 있는 소재와 유리섬유강화재 중량 비율로 제작된 선박의 외판을 검사체로 선정하고, Pulse-Echo 초음파 탐상기를 활용하여 GFRP(Glass Fiber-Reinforced Plastics) 선체 외판의 초음파 탐상을 위한 적정 조건을 조사하였다. 1.00 MHz, 2.25 MHz, 5.00 MHz 세 종류 탐촉자로 A-Scan 을 실시하였으며 선체 외판의 두께 검사결과와 비교분석함으로써 적정 초음파 탐상 조건을 찾고자 하였다. 연구결과 탐촉자의 초음파 주파수가 높아질수록 수신자의 반사파 음향 속력을 감소시켜야 더 정도 높은 두께 측정 결과를 얻을 수 있었으며, 상대적으로 낮은 초음파 주파수 탐촉자에서 더 적은 오차가 발생함을 확인할 수 있었다.

Nondestructive testing is one of the most commonly used quality inspection methods for evaluating ship structures. However, accurate evaluation is difficult because various composite materials, such as reinforcements, resin, and fiber-reinforced plastics (FRPs), are used in hulls, and manufacturing quality differences are likely to exist owing to the fabrication environment and the skill level of workers. This possibility is especially true for FRP ships because they are significantly thicker than other structures, such as automobiles and aircraft, and are mainly manufactured using the hand lay-up method. Because the density of a material is a critical condition for ultrasonic inspection, in this study, a hull plate was selected from a vessel manufactured using e-glass fiber, which is widely used in the manufacture of FRP vessels with the weight fraction of the glass content generally considered. The most suitable ultrasonic testing conditions for the glass FRP hull plate were investigated using a pulse-echo ultrasonic gauge. A-scans were performed with three probes (1.00, 2.25, and 5.00 MHz), and the results were compared with those of the hull plate thickness measured using a Vernier caliper. It was found that when the probe frequency was higher, the eco-pulse velocity of the receiver had to be lowered to obtain accurate measurement results, whereas fewer errors occurred at a relatively low probe frequency.

목차
요 약
Abstract
1. 서 론
2. GFRP 생산설계 조건과 초음파 탐상 조건
3. GFRP 선체 외판의 Pulse-Echo 초음파 탐상
    3.1 실험방법 및 절차
    3.2 GFRP 선체 외판의 생산설계와 검사체 분석
    3.3 FRP 선체 외판의 초음파 탐상과 결과분석
4. 결론 및 고찰
References
저자
  • 이상규(목포해양대학교 대학원) | Sang-gyu Lee (Graduate School Mokpo National Maritime University)
  • Zhiqiang Han(목포해양대학교 대학원)
  • 이창우(한국조선해양기자재연구원 전남본부) | Chang-woo Lee (Korea Marine Equipment Research Institute)
  • 오대균(목포해양대학교 조선해양공학과) | Daekyun Oh (Department of Naval Architecture and Ocean Engineering, Mokpo National Maritime University) Corresponding Author