In this study, two alignment methods were used to create a Fringe-Field Switching (FFS) mode liquid crystal device using an organic thin film (polyimide: PI) as an alignment layer. In addition, the electro-optical (EO) characteristics of the liquid crystal device manufactured in this way were investigated to evaluate the feasibility of mass production application of the technology. In general, the photo-alignment method using unpolarized ultraviolet rays can obtain a relatively low pretilt angle, so a liquid crystal device in FFS mode, which is a driving mode of the liquid crystal device that reflects the characteristics of liquid crystal alignment, was manufactured, and the liquid crystal has a high reactivity with the alignment film. Considering this, nematic liquid crystal (NLC) was used. In addition, in order to improve the misalignment, it was observed whether more stable orientation occurred by irradiating ultraviolet rays for an additional 1 to 3 hours in the aligned state. As a result of the experiment, it was found that NLC alignment occurs through a photodecomposition reaction caused by unpolarized UV irradiation oblique to the PI surface. In addition to the existing orientation method, UV irradiation was used to achieve a more stable orientation state and stable V-T curve and response characteristics. With liquid crystal alignment completed, more stable orientation characteristics and EO characteristics at the mass production level were obtained through additional UV irradiation for 3 hours. This method can further stabilize the orientation stability caused by existing UV irradiation through an additional process.

In the automotive information display device industry, products with high reliability and wide temperature conditions are required, and interest in products that do not cause lighting defects even under extremely low temperature conditions is increasing. In this experiment, we produced an LED backlight unit for car navigation in a cryogenic environment. And to make this backlight unit, we used 12 side-emitting white LEDs with 3[W] high power LEDs. This backlight unit emits up to 18,000[nits] at a power consumption of 36[W] and has a startup voltage time of less than 1[ms] at -50° ambient temperature.

Recently, as the demand for a non-contact liquid crystal alignment method capable of improving viewing angle characteristics has spread throughout the industry, various non-contact liquid crystal alignment methods, including conventional UV light alignment, are being actively studied. In the case of UV light alignment, it is currently applied to mass production in many fields and shows relatively excellent initial characteristics, but there is a problem of display quality deterioration over time. In this study, among these non-contact liquid crystal alignment methods, the liquid crystal is oriented by quantitatively irradiating an ion beam onto the SiOF inorganic film, which has excellent initial characteristics and does not cause deterioration in quality over time., the electro-optical properties were evaluated by manufacturing a commercial-level IPS (In-Plane Switching) liquid crystal cell. In particular, in the case of such inorganic film orientation, it is common to have many problems with orientation stability, but the evaluation cell manufactured by the method proposed in this study is capable of maintaining a uniform orientation without losing orientation even after heat treatment at a high temperature of 200°C. could be observed.

In this study, we studied the method of using general architectural glass instead of using the existing acrylic material for high luminance flat lighting. The flat panel lighting used the side illumination method to increase the ease of installation and aesthetic satisfaction. In general, glass has an amorphous structure with a lower angle of refraction than acrylic, so it is not suitable for use in flat panel lighting as a light guide, but in this study, the role of light distribution characteristics and diffusion patterns in the case of using such a glass light guide. Quantitative simulations were conducted to confirm new possibilities. In the simulation, the backlight estimation method was used, and about 10,000,000 rays were placed within a unit area in order to obtain a result similar to the real thing. As a result of the simulation, the geometry of the diffusion pattern could be specified, and the value of the geometry could be quantified using the ratio of the diameter and height of the pattern. As a result of the calculation, it was found that the maximum amount of light was generated around 75 degrees by quantitatively calculating the ratio and the outgoing light angle at which the maximum value of the outgoing light occurred between 05 and 1.0. As a result of these studies, it was confirmed that it is possible to use ordinary glass at the same time as a transparent window and light-emitting lighting at night.