The research work was undertaken to determine an effective fertilization medium, sperm separation method and sperm capacitating agent for optimum in vitro fertilization (IVF) rates of indigenous zebu cow oocytes. In experiment 1, tissue culture medium (TCM 199), Tyrode’s albumin lactate pyruvate (TALP) and Brackett and Oliphant (BO) medium were used as basic medium for IVF of oocytes of indigenous zebu cows. In experiment 2, three sperm separation methods namely centrifugation, swim up and percoll gradient methods were used for separation of motile and viable spermatozoa for IVF. In experiment 3, for capacitation of spermatozoa, IVF medium supplemented with the heparin, mixture of penicillamine, hypotaurine and epinephrine (PHE) or the combination of heparin with PHE were used for fertilization. In vitro culture (IVC) of presumptive zygotes was done in modified synthetic oviduct fluid (mSOF) medium using standard procedure 24 h after sperm-oocytes co-culture. The cleavage rate was determined to evaluate the efficacy of fertilization medium, sperm separation method and sperm capacitating agent 24 h after IVC. The cleavage rate was higher in oocytes fertilized in TALP (63.3%) than in TCM 199 (47.5%) (p < 0.05). The cleavage rate was higher in oocytes fertilized by spermatozoa separated by percoll gradient method (62.3%) than by centrifugation (51.6%) (p < 0.05). The cleavage rate of oocytes was higher when insemination was done with spermatozoa capacitated in TALP supplemented with heparin and PHE (61.3%) compared to control (40.9%) (p < 0.05). In conclusions, TALP based medium and percoll gradient sperm separation followed by capacitation with combination of heparin and PHE are suitable for IVF of indigenous zebu cow oocytes in Bangladesh.

The purpose of this study was to establish the optimum experimental conditions by investigating the relationship between the nine experimental conditions using Taguchi technique. Through experiments, we found that the weight, thickness, and length of the sample were most affected by the angle at which the sample was installed, while the width had the largest influence on the sample's x-axis and the inner diameter. It was confirmed. Therefore, through this experiment, it was confirmed that the installation angle of the product had the greatest influence on the error occurrence of the product during 3D printer processing.

Anticipation of welding deformation with finite element method is a very interested topic in the industries, adequate heat source model is essential for concluding reasonable results. This study is related to estimate the parameters of Goldak heat source model, and global optimization algorithm is applied to this research. The heat affected zone (HAZ) boundary line of bead on plate (BOP) welding is used as the target, parameters of heat sources are used as the variables. Adaptive simulated annealing is applied and the optimal result is obtained out of 1,000 candidates. The convergence of finite element method and the global optimization is meaningful for estimation of welding deformation, which could enhance to reduce the resources and time for experiments.

Forged part made of Cold heading quality wire materials are used for automotive brake systems. The cost reduction of forged products is a major issue because of the strict shape change. A series of studies were conducted to minimize the cost of EPB spindle process among brake parts. In order to reduce the material cost, heat treatment-abbreviated material was applied and the formability on the processes was verified by the ductile fracture theory. In addition, the causes of shape fixation and die life degradation were analyzed using the numerical simulation. The process cost has been minimized by re-designing process, changing the product shape, and the die material.

In this study, optimizations were carried out for a heater core and an evaporator installed in a passenger car. The main geometric parameters of each component were selected as design variables, and the main performances examined were the outlet temperature and the pressure drop. In addition, the sensitivity analysis was performed to grasp the dominant design variable. The thermal flow analysis for each component was performed using the commercial program STAR CCM+. On the other hand, EasyDesign, a commercial program based on DOE and metamodel-based optimization, was used as an optimization tool. The optimized performances of the heater core were compared with performance target, and finally, the improved designs of the heater and the evaporator were presented.

본 연구는 국내 특산식물이며 관상소재로 개발이 가능한 산꼬리풀의 효과적인 육묘조건을 구명하기 위해 수행되었다. 육묘는 토양 종류와 비료 농도, 차광정도, 추비 농도, 종자의 광원 전처리 및 채종 시기별로 각 요인을 달리하여 수행하였 다. 연구 결과, 산꼬리풀은 원예상토에서 생육이 우수하였으며, 혼용토에서는 비료 첨가 시 생육이 억제되었다. 차광은 55% 차광조건에서 무차광에 비해 전체적인 생육이 향상되었다. 고농도(1000mg·L-1)의 Hyponex는 육묘 시 생육을 촉진 하였으며, 파종 전 종자에 대한 적색광 조사는 추후 초장과 생체중 향상에 효과적이었다. 채종 시기는 2018년도 종자가 2017년 종자보다 생육이 우수하였다.

Fast service access involves keeping track of the location of mobile users, while they are moving around the mobile network for a satisfactory level of QoS (Quality of Service) in a cost-effective manner. The location databases are used to keep track of Mobile Terminals (MT) so that incoming calls can be directed to requested mobile terminals at all times. MT reporting cell system used in location management is to designate each cell in the network as a reporting cell or a non-reporting cell. Determination of an optimal number of reporting cells (or reporting cell configuration) for a given network is reporting cell planning (RCP) problem. This is a difficult combinatorial optimization problem which has an exponential complexity. We can see that a cell in a network is either a reporting cell or a non-reporting cell. Hence, for a given network with N cells, the number of possible solutions is  . We propose a biogeography based optimization (BBO) for design of mobile station location management system in wireless communication network. The number and locations of reporting cells should be determined to balance the registration for location update and paging operations for search the mobile stations to minimize the cost of system. Experimental results show that our proposed BBO is a fairly effective and competitive approach with respect to solution quality for optimally designing location management system because BBO is suitable for combinatorial optimization and multi-functional problems.

This study aims to optimize the cochlea-inspired artificial filter bank (CAFB) using El-Centro seismic waveforms and test its performance through a shaking table test on a two-span bridge model. In the process of optimizing the CAFB, El-Centro seismic waveforms were used for the purpose of evaluating how they would affect the optimizing process. Next, the optimized CAFB was embedded in the developed wireless-based intelligent data acquisition (IDAQ) system to enable response measurement in real-time. For its performance evaluation to obtain a seismic response in real-time using the optimized CAFB, a two-span bridge (model structures) was installed in a large shaking table, and a seismic response experiment was carried out on it with El-Centro seismic waveforms. The CAFB optimized in this experiment was able to obtain the seismic response in real-time by compressing it using the embedded wireless-based IDAQ system while the obtained compressed signals were compared with the original signal (un-compressed signal). The results of the experiment showed that the compressed signals were superior to the raw signal in response performance, as well as in data compression effect. They also proved that the CAFB was able to compress response signals effectively in real-time even under seismic conditions. Therefore, this paper established that the CAFB optimized by being embedded in the wireless-based IDAQ system was an economical and efficient data compression sensing technology for measuring and monitoring the seismic response in real-time from structures based on the wireless sensor networks (WSNs).

In the era of the Fourth Industrial Revolution, Various attempts are being made to converge new industries with IT industry to find new growth engines in the field of IT, maximizing efficiency in terms of productivity. 3D printers are also related to this, and various studies have been conducted worldwide to utilize them in the construction industry. At present, there is an active effort to study atypical structures using 3D printers. The most widely used method is the use of glass panels, however, the additional cost of the manufacturing process and thus the overall project cost cannot be ignored. In addition, the construction of the curvature of the existing two-way curved surface in the conventional flat joint method is not suitable for implementing an amorphous shape. In this paper, we propose an optimized shape through Abaqus analysis of various shapes of Space Truss interior using 3D printing technology using polymer.

The purpose of this study is to experimentally figure out thermal performances of a newly developed wavy patterned heat plates(first heat plates) which are known to have better thermal performances than the conventional heat plates. Three types of products were made with high and low chevron angled plates. The test results show that overall heat transfer coefficients and pressure drops increased with flow rates and chevron angles just like other studies. Another purpose of this study is to find a way to reduce pressure drops while maintaining or even improving the heat transfer characteristics of the first heat plates. Research on optimization of the distribution area on the heat plate to achieve the even fluid distribution was conducted, and then the second heat plates were developed to reflect the research results. Another new three types of products with the second heat plates were manufactured and tested, too. The test results of the second heat plates were compared with those of the first heat plates to find out how the distribution area contributed to the thermal performances of the heat plates. The comparison showed that distribution area optimization could affect thermal performances of the high chevron angled plate positively, but the low chevron angled plate had little effect from the optimization. This is considered to be because the low chevron angled plate itself has a characteristic that the pressure drop is small.

Powder characteristics, such as density, size, shape, thermal properties, and surface area, are of significant importance in the powder bed fusion (PBF) process. The powder required is exclusive for an efficient PBF process. In this study, the particle size distribution suitable for the powder bed fusion process was derived by modeling the PBF product using simulation software (GeoDict). The modeling was carried out by layering sintered powder with a large particle size distribution, with 50 μm being the largest particle size. The results of the simulation showed that the porosity decreased when the mean particle size of the powder was reduced or the standard deviation increased. The particle size distribution of prepared titanium powder by the atomization process was also studied. This study is expected to offer direction for studies related to powder production for additive manufacturing.

억새와 같은 초본계 바이오매스로부터 cellulose, hemicellulose, lignin 등 주요성분을 추출하기 위해서는 알칼리 전처리가 효율적이며, 본 연구에서는 수산화칼륨(KOH)을 이용한 전처리 조건을 최적화하였다. 전처리 변수의 최적화는 반응표면분석법(RSM)을 적용하였다. RSM의 변수는 3개였으며, 변수범위는 각각 KOH 0.2∼0.8M, 반응온도 110∼190℃ 및 반응시간 10∼90min 이었다. 억새의 알칼리 전처리를 위한 최적조건은 KOH 농도 0.47M, 반응온도 134℃ 및 반응시간 65min 이었다. 최적 전 처리 조건에 따라 전처리를 수행한 후 고형물의 cellulose 함량은 66.1±1.1% 이었으며, hemicellulose 및 lignin 함량은 각각 26.4±0.4%, 3.7±0.1% 이었다. RMS 모델식에 따라 계산된 예측값은 실제값 대비 95% 범위 내에서 유효하였다. 최종적으로 전처리물을 동시당화발효를 통해 검증한 결과 에탄올 생산 수율은 96% 이었다.

CKD 추출액은 시멘트공정에서 발생한 폐기물인 CKD를 시멘트 원료로 재사용하기 위해 공정 방해물질로 작용하는 KCl을 추출한 폐수이며, 폐수처리시설 증설 등의 문제로 추출액 무방류 및 이를 재이용하고자 하였다. 이온교환법을 적용하여 KCl을 제거한 결과, 이온교환 후 추출액의 pH는 12.7 에서 pH 2 미만으로 감소하였으며 양이온교환수지의 H+가 이온교환을 거쳐 추출액에 용해되었음을 확인하였다. 이온교환의 선택성에 의해 Ca2+, K+ 순서로 제거되었으며, K+ 이온을 제거하기 위해 접촉시 간의 증가가 필요함을 판단하였다. 이온교환수지와 직접접촉시간이 약 6배 높은 접촉시간을 갖는 회분 식장치에서 연속흐름식장치 대비 4배 높은 K+ 제거 효율을, 7배 높은 Cl- 제거 효율을 확인하였다. 양이온교환수지의 H+가 음이온교환수지의 OH- 대비 1.2배 빠른 교환속도를 가짐을 추출액 pH 변화를 통해 확인하였다.

In this study, the shape optimization of the injector according to fuel and tip was conducted through analytical techniques. As an analysis condition, a flow rate of 0.08 kg / s was applied to the inlet and the outlet was given a condition of 0 Bar. The working fluid for each fuel was applied. As a result of the analysis, it can be seen that the pressure and velocity of model with the modified tip become higher than that of the base model in diesel. Compared with the base model in the case of gasoline, the modified model of the tip was found to have more stable injection when the pressure inside the combustion chamber and the straightness of the fuel were observed. Finally, in case of LPG injector, the same modified tip as gasoline was found to be the more stable injection. On the basis of this study result, the shape parameters of the injector can be inferred.

The purpose of this study was to optimize the rice protein extracted using a response surface methodology. The experiment was designed based on a CCD (Central Composite Design), and the independent variables were the high pressure (X1, 0-400 MPa) and processing time (X2, 0-10 minutes). The results of the extraction content (Y1), residue content (Y2), and recovery yield (Y3) were fitted to a response surface methodology model (R2= 0.92, 0.92, and 0.93, respectively). Increasing the pressure and processing time has a positive effect on the extraction content (Y1), residue content (Y2), and recovery yield (Y3). Therefore, these high-pressure conditions (independent variables) can significantly affect the improvement in rice protein extraction efficiency. Thus, the optimal conditions of X1 and X2 were 400 MPa and 10 min., respectively. Under these optimal conditions, the predicted values of Y1, Y2, and Y3 were 62.93, 57.53 mg/g, and 91.76%, respectively.

본 논문에서는 AISC 표준 단면을 설계 변수로 하는 캔틸레버 타입 헬리데크 모델의 유전 알고리즘 최적설계를 소개한다. AISC 표준 단면을 단면 형상별로 분류하고 단면적 순으로 정렬한 후 정수 단면 번호를 부여하여 설계 변수로 최적설계를 수행하였다. 이 과정을 통하여 이산화된 설계 변수를 가지는 최적설계 문제를 해결하기 위해 유전 알고리즘을 적용하였다. 또한, 제약조건으로 허용응력 및 허용응력비 검사 조건을 모두 고려하여 구조물의 구조 안정성을 고려한 설계를 수행하였다. 최적설계 과정중 매 반복계산 마다 수행되는 구조해석 시간을 단축시키기 위해 선형 중첩법을 사용하였고, 이를 통해 구조 해석 시간을 약 75% 감소시킬 수 있었다. 또한 헬리데크 최적설계의 경량 효과를 높이기 위해 부재 그룹 세분화를 하였고, 그 결과를 선행 연구 모델, 기존의 부재 그룹 모델과 비교하였다. 그 결과 선행연구 대비 약 30톤의 부재를 절감할 수 있었으며, 구조적으로도 보다 안전한 헬리데크 설계를 얻을 수 있었다.