This paper proposes the armored combat bulldozer, essential for amphibious tasks, requires water ingress prevention and submersion capabilities, typically addressed by a centrifugal pump. This study aims to boost the bulldozer's drainage pump efficiency by replacing the traditional aluminum 3-blade impeller with one made of ASA material using 3D printing. Analysis via ANSYS Fluent revealed that the 5-blade impeller increased discharge volume by 19.31% and efficiency by 6.07%, while the 6-blade variant saw a 27.07% increase in discharge volume and 8.81% efficiency improvement. Further scrutiny with ANSYS Static Structure ensured the new impellers' structural integrity and robustness under extreme conditions. This research confirms the potential of 3D printing in enhancing military equipment, demonstrating significant improvements in pump performance and opening paths for advanced manufacturing techniques to meet the demanding needs of combat vehicles.

Aluminum alloys, known for their high strength-to-weight ratios and impressive electrical and thermal conductivities, are extensively used in numerous engineering sectors, such as aerospace, automotive, and construction. Recently, significant efforts have been made to develop novel aluminum alloys specifically tailored for additive manufacturing. These new alloys aim to provide an optimal balance between mechanical properties and thermal/ electrical conductivities. In this study, nine combinatorial samples with various alloy compositions were fabricated using direct energy deposition (DED) additive manufacturing by adjusting the feeding speeds of Al6061 alloy and Al-12Si alloy powders. The effects of the alloying elements on the microstructure, electrical conductivity, and hardness were investigated. Generally, as the Si and Cu contents decreased, electrical conductivity increased and hardness decreased, exhibiting trade-off characteristics. However, electrical conductivity and hardness showed an optimal combination when the Si content was adjusted to below 4.5 wt%, which can sufficiently suppress the grain boundary segregation of the α- Si precipitates, and the Cu content was controlled to induce the formation of Al2Cu precipitates.

In this study, the biogeochemistry management (BGC-MAN) model was applied to North and South Korea pine and oak forest stands to evaluate the Net Primary Productivity (NPP), an indicator of forest ecosystem productivity. For meteorological information, historical records and East Asian climate scenario data of Shared Socioeconomic Pathways (SSPs) were used. For vegetation information, pine (Pinus densiflora) and oak (Quercus spp.) forest stands were selected at the Gwangneung and Seolmacheon in South Korea and Sariwon, Sohung, Haeju, Jongju, and Wonsan, which are known to have tree nurseries in North Korea. Among the biophysical information, we used the elevation model for topographic data such as longitude, altitude, and slope direction, and the global soil database for soil data. For management factors, we considered the destruction of forests in North and South Korea due to the Korean War in 1950 and the subsequent reforestation process. The overall mean value of simulated NPP from 1991 to 2100 was 5.17 Mg C ha-1, with a range of 3.30-8.19 Mg C ha-1. In addition, increased variability in climate scenarios resulted in variations in forest productivity, with a notable decline in the growth of pine forests. The applicability of the BGC-MAN model to the Korean Peninsula was examined at a time when the ecosystem process-based models were becoming increasingly important due to climate change. In this study, the data on the effects of climate change disturbances on forest ecosystems that was analyzed was limited; therefore, future modeling methods should be improved to simulate more precise ecosystem changes across the Korean Peninsula through processbased models.

Aluminum alloys are widely utilized in diverse industries, such as automobiles, aerospace, and architecture, owing to their high specific strength and resistance to oxidation. However, to meet the increasing demands of the industry, it is necessary to design new aluminum alloys with excellent properties. Thus, a new method is required to efficiently test additively manufactured aluminum alloys with various compositions within a short period during the alloy design process. In this study, a combinatory approach using a direct energy deposition system for metal 3D printing process with a dual feeder was employed. Two types of aluminum alloy powders, namely Al6061 and Al-12Cu, were utilized for the combinatory test conducted through 3D printing. Twelve types of Al-Si-Cu-Mg alloys were manufactured during this combinatory test, and the relationship between their microstructures and properties was investigated.

Metal additive manufacturing (AM) has transformed conventional manufacturing processes by offering unprecedented opportunities for design innovation, reduced lead times, and cost-effective production. Aluminum alloy, a material used in metal 3D printing, is a representative lightweight structural material known for its high specific strength and corrosion resistance. Consequently, there is an increasing demand for 3D printed aluminum alloy components across industries, including aerospace, transportation, and consumer goods. To meet this demand, research on alloys and process conditions that satisfy the specific requirement of each industry is necessary. However, 3D printing processes exhibit different behaviors of alloy elements owing to rapid thermal dynamics, making it challenging to predict the microstructure and properties. In this study, we gathered published data on the relationship between alloy composition, processing conditions, and properties. Furthermore, we conducted a sensitivity analysis on the effects of the process variables on the density and hardness of aluminum alloys used in additive manufacturing.

본 연구에서는 경기도내 유통되고 있는 심해성 어류 50 건을 대상으로 수은, 메틸수은의 오염도 및 셀레늄의 함 량을 알아보았다. 금아말감법의 수은분석기, ICP-MS를 사 용하여 측정하였으며 각 항목별 평균함량은 수은 0.7647 mg/ kg (0.0182-5.3620), 메틸수은 0.0764 mg/kg (0.0096-0.8750), 셀레늄 0.4728 mg/kg(0.1075-3.5100)으로 메틸수은은 50건 모두 기준규격(1.0 mg/kg) 이하로 나타났다. 셀레늄은 수 은과 결합하여 수은의 독성을 감소시키는 것으로 알려져 있으며, 본 연구과제에서는 일일평균섭취량이 3.3 μg/kg으 로 일일권장량보다 낮은 수치였다. 유해물질인 수은과 메 틸수은은 JECFA에서 설정한 PTWI의 5.7%, 1.8%로 조사 되었다. 따라서 도내에서 유통되는 심해성 어류의 수은, 메틸수은과 같은 위해중금속은 안전한 것으로 나타났지만 지속적 모니터링이 필요하다고 판단된다.

This study compared the antioxidant and mineral properties of the leaves and seeds of fifteen Korean adzuki bean (Vigna angularis L.) breeding lines. This study was conducted in an attempt to expand the use of Korean adzuki bean leaves. The potassium, calcium, magnesium, and sodium contents of the leaves were significantly higher than the seeds, in particularly, the potassium content. The leaves had approximately 3.3 times higher potassium content than the seeds. For instance, the potassium content of YA1317 leaves was 21% higher than that of Arari. The total polyphenol content and ABTS activity of Adzuki bean leaves were significantly higher than the seeds, as opposed to the total flavonoid content and DPPH scavenging activity. Among the 15 breeding lines, YA1402 had 1.2~3.2 times higher antioxidant content and activity as compared to the Arari variety. It was concluded that adzuki bean leaves had higher mineral content, antioxidant component and activity as compared to the seeds. Therefore, adzuki bean leaves could be used an ingredient for dishes and as a medicine.

Barnea manilensis is a bivalve which bores soft rocks, such as, limestone or mudstone in the low intertidal zone. They make burrows which have narrow entrances and wide interiors and live in these burrows for a lifetime. In this study, the morphology and the microstructure of the valve of rock-boring clam B. manilensis were observed using a stereoscopic microscope and FE-SEM, respectively. The chemical composition of specific part of the valve was assessed by energy dispersive X-ray spectroscopy (EDS) analysis. 3D modeling and structural dynamic analysis were used to simulate the boring behavior of B. manilensis. Microscopy results showed that the valve was asymmetric with plow-like spikes which were located on the anterior surface of the valve and were distributed in a specific direction. The anterior parts of the valve were thicker than the posterior parts. EDS results indicated that the valve mainly consisted of calcium carbonate, while metal elements, such as, Al, Si, Mn, Fe, and Mg were detected on the outer surface of the anterior spikes. It was assumed that the metal elements increased the strength of the valve, thus helping the B. manilensis to bore sediment. The simulation showed that spikes located on the anterior part of the valve received a load at all angles. It was suggested that the anterior part of the shell received the load while drilling rocks. The boring mechanism using the amorphous valve of B. manilensis is expected to be used as basic data to devise an efficient drilling mechanism.

붕어(무게 28.1±3.7 g, 길이 10.0±1.0 cm)에 0, 2.0×104, 2.0×105, 2.0×106, 2.0×107 CFU/ml의 Aeromonas hydrophila를 주사 후 2주간 실험을 실시하였다. A. hydrophila로 인위감염한 Carassius carassius의 2주 뒤 반수치사농도는 19.776×105 CFU/ml이었다. 혈액학적 지표에서는 A. hydrophila에 의해 혈색소와 적혈구 수가 유의하게 감소한 반면, 적혈구 용적은 유의적 변 화가 없었다. 마그네슘, 칼슘과 같은 혈장 무기 성분은 유의적으로 감소하였다. 유기 혈장 성분 에서 A. hydrophila 인위감염에 의해 혈장 포도당과 콜레스테롤이 유의하게 증가한 반면, 총 단 백질은 유의하게 감소하였다. 혈장 효소 성분인 ALP는 A. hydrophila 인위감염에 의해 유의하 게 증가하였다. 본 연구의 결과는 C. carassius에 대한 A. hydrophila의 인위감염이 치명적인 병원성 세균으로 혈액학적 성상 및 혈장 성분에 유의한 생리학적 변화를 유도하였음을 의미 한다.

본 실험은 붕어(Crucian carp, Carassius carassius)(무게 39.7±3.1 g, 전장 14.8±0.5 cm)의 수인 성 니켈 0, 10, 20, 40, 80 및 160 mg Ni2+/l 농도로 96시간 급성 노출을 실시하였다. 수인성 니 켈에 노출된 붕어의 반수치사농도(LC50)는 117.69 mg Ni2+/l으로 나타났다. 혈액학적 성상에서 RBC count는 수인성 니켈 96시간 급성 노출 중 48시간에서 유의적으로 증가한 반면, 96시간에 서 유의적 감소가 나타났다. MCV와 MCH는 96시간에서 80 mg Ni2+/l 농도에서 유의적으로 증 가했다. Calcium, magnesium, glucose, cholesterol, total protein, AST, ALT 및 ALP 와 같은 혈장 성분은 수인성 니켈 노출에 의해 유의적 변화가 나타났다. 이 연구의 결과는 수인성 니켈 노출 에 따른 붕어의 생존율, 혈액학적 성상 및 혈장 성분의 변화를 확인하고 이는 수인성 니켈의 독성에 의한 것으로 판단했다.

Environmental issues such as global warming due to fossil fuel use are now major worldwide concerns, and interest in renewable and clean energy is growing. Of the various types of renewable energy, green hydrogen energy has recently attracted attention because of its eco-friendly and high-energy density. Electrochemical water splitting is considered a pollution-free means of producing clean hydrogen and oxygen and in large quantities. The development of non-noble electrocatalysts with low cost and high performance in water splitting has also attracted considerable attention. In this study, we successfully synthesized a NiCo2O4/NF electrode for an oxygen evolution reaction in alkaline water splitting using a hydrothermal method, which was followed by post-heat treatment. The effects of heat treatment on the electrochemical performance of the electrodes were evaluated under different heat-treatment conditions. The optimized NCO/NF-300 electrode showed an overpotential of 416 mV at a high current density of 50 mA/cm2 and a low Tafel slope (49.06 mV dec-1). It also showed excellent stability (due to the large surface area) and the lowest charge transfer resistance (12.59 Ω). The results suggested that our noble-metal free electrodes have great potential for use in developing alkaline electrolysis systems.

리튬-이온 전지 기술의 발전과 함께 다량의 리튬 사용에 따라 리튬-이온 전지에 대한 수요와 공급의 균형이 무너지고 있으며, 따라서 리튬을 대체할 수 있는 차세대 이차 전지의 개발이 필요해지고 있다. 최근 친환경적이며, 값싸며 안전 하고, 다가의 전자를 활용할 수 있는 아연 이온을 활용하는 수계 아연-이온 전지가 주목받고 있다. 그럼에도 불구하 고 아연-이온 전지에 사용될 수 있는 전류 집전체에 대한 개발 연구는 거의 없으며, 특히 현재 사용되고 있는 금속 기반의 전류 집전체는 그 무게가 무거워 실용적으로 사용되기 힘들다. 본 연구에서는 접착 특성이 매우 우수한 키틴 바인더를 사용하여 집전체 없이 지탱이 가능한 전극을 개발하였으며 아연-이온 전지에서의 그 특성을 평가하였다. 전 극 제조는 전통적인 코팅법과 스핀 코팅법을 사용하여 비교하였으며, 스핀 코팅이 더 균일한 전극 형성과 함께 더 우 수한 배터리 성능을 나타냄을 확인하였다.

This mini-review focused on the current advances in the development and the application of the antibacterial agents produced from probiotics strains against foodborne pathogens. Inhibitory activity of the pathogen growth could be achieved by co-culture with probiotics and/or the treatment of metabolites extracted from probiotics culture, whereas strain-dependent efficacy was mainly reported according to the bacterial species of the target pathogens. To overcome the limited antibacterial spectrum and the efficacy of the metabolites from probiotics, the recent research highlight the discovery of novel bioactive substances with broad range of the inhibitory activity of foodborne pathogens and mode-of-action which has not been reported as the major research goal. Moreover, understanding the distribution of functional and regulation genes coding the production of the antibacterial metabolites based on the bacterial genome analysis can provide the clues for the mechanisms of the pathogen control by using probiotics. Major strategies on the application of the genomics in this research area can be represented as follows: 1) functional annotation specialized for antimicrobial proteins, 2) assessment of the antibacterial effects followed by the general/functional annotation, 3) genome and metabolites analysis for the purification of antimicrobial proteins, 4) comparative genomics and the characterization of antimicrobial potential. Especially the relationship between phenotype-genotype based on genomic bioinformation with the results of the practical efficacy tests of bacterial metabolites as an active substance of disinfectants and/or preservatives can be expected to act as supportive research for broadening our knowledge regarding the key metabolic pathways associated with the production of antibacterials from probiotics.

본 연구에서는 정서곤충을 이용한 치유프로그램 활동이 지역아동센터를 이용하는 아동 43명의 스트레스에 미치는 영향을 조사하였다. 치유 프로그램에 이용된 정서곤충은 누에나방[Bombyx mori (Linnaeus)]이다. 스트레스의 정도는 타액 ɑ-아밀라아제 검사를 통해 측정하였다. 스트레 스 수치를 평가하기 위한 타액 샘플 채취와 곤충 선호도에 대한 설문지는 곤충치유활동에 참여하기 전과 후에 측정되었고, 활동을 모두 마친 후에는 치유프로그램 참여 경험에 대한 만족도 점수를 평가하였다. 분석 결과, 곤충치유프로그램 활동은 참여 아동의 타액 ɑ-아밀라아제 수치를 통계적으 로 낮추고, 곤충에 대한 선호도를 높여준다는 결과를 확인하였다. 누에를 이용한 치유프로그램 활동에 참가한 아동들의 만족도는 5점 만점에 4.23 점이었다.

선박, 잠수함이 추진하면 수중구조물 후류에 와류가 발생하고 이에 따른 와류기인 구조진동이 유발된다. 최근 선박, 잠수함의 고속화 및 대형화 추세에 따라 고차모드에서 유발되는 와류기인 진동 및 피로파괴에 대한 중요성이 강조되고 있다. 고속 유속환경의 와 류는 저속 유속환경 대비 큰 진동을 유발하므로 이에 관한 연구가 필요하다. 본 연구에서는 수중날개 고차모드에서 유발되는 와류기인 진동을 예측하기 위한 하이브리드 유체구조연성 해석 방법론을 제시하였다. 고차모드를 고려한 하이브리드 유체구조연성 해석을 수행하 여 와류기인 진동을 도출하고 실험결과와 비교함으로써 방법론을 검증하였다. 최종적으로 와류기인 진동으로부터 도출된 최대 von Mises 응력을 노르웨이 선급에서 제시한 S-N 선도에 적용함으로써 고차모드 유체구조연성 해석의 효용성을 확인하였다. 고차모드를 고려하여 와류기인 진동응답을 도출할 경우 유체구조연성에 의한 락인(Lock-in) 특성을 확인하였으며 고려하지 않은 경우 대비 진동응답과 최대 von Mises 응력에서 10배 이상의 차이를 보였다. 향후에는 외팔보 경계조건 및 형상에 대한 확장연구가 필요하다.

｢곤충산업의 육성 및 지원에 관한 법률｣ 제6조에 따라 국립농업과학원에서는 2020년도에 곤충산업 종사자를 대상으로 실태조사를 실시하 였다. 곤충산업 종사자의 유형은 생산업이 가장 많았고(98.5%), 남성 비율이 높았으며(80.4%), 연령은 50대가 36.4%로 가장 많았다. 산업곤충 의 생산 유형은 식약용 곤충 66.5%, 사료용 12.8%, 애완용 20.7%였으며, 식약용 곤충 중 흰점박이꽃무지는 69.6%로 가장 많이 생산되고 있었 으며, 사료용으로는 귀뚜라미류가 31.2%, 애완(정서)용으로는 장수풍뎅이가 45.6%로 가장 많이 생산되고 있었다. 제품의 형태는 분말이 68.5% 로 가장 높았고, 생물로 판매되는 경우는 40.9%로 조사되었다. 연간 소득이 있는 곤충농가는 77.3%이고, 그 중에서 연간 판매금액이 2천만원 미 만인 경우가 65.4%를 차지하였다. 곤충산업 종사자들의 가장 큰 애로사항은 판로 확보로 조사되었다(84.0%). 이와 같이 곤충산업 종사자는 매 년 늘어나고 있지만 20대~40대 청년 곤충농가 대표는 줄어들고 있고, 생산은 특정 대표 곤충 종에 한정되어 있으며, 매우 영세하게 농가가 유지 되고 있음을 알 수 있다. 또한 곤충 농가에서는 판로확보에 가장 큰 어려움을 느끼고 있어 산업곤충 소비 촉진을 위한 이용 기술 개발이 시급하다 고 판단된다.