본 연구에서는 폐타이어를 파쇄한 재생 SBR(Styrene-Butadience Rubber)을 사용하여 탄성 고무 층 의 파단 시의 인장 강도 및 연신도와 같은 인장특성 및 충격 흡수 및 수직 변형과 같은 동적특성을 평가하였고, 섬유 보강재를 혼입하여 탄성 고무 층의 취약점을 개선시키고자 하였다. 주요변수로 다짐 횟수, 바인더-고무분말 비율, 양생기간, 양생온도, 양생습도, 섬유 보강재의 종류를 고려하였다. 실험 결과, 재생 SBR을 사용한 탄성 고무 층의 인장 강도는 다짐 횟수, 바인더-고무분말 비율, 양생기간 및 온도가 증가함에 따라 증가하였으며, 파단 시 연신도는 양생온도와 기간에 영향을 받는 것으로 나 타났다. 충격 흡수와 수직 변형은 다짐횟수 및 바인더-고무분말 비율이 증가함에 따라 경도가 증가하 여 감소하는 경향을 나타내었다. 또한 양생온도가 탄성 고무 층의 인장 특성에 뚜렷한 영향을 미치며, 적절한 양생온도를 유지할 경우(약 50℃) 상대적으로 낮은 탄성 고무 층의 인장 특성을 개선할 수 있는 가능성을 제시하였다. 보강재로 폴리머 합성 섬유인 Polypropylene(PP), Polyester(PET), Nylon(NY)을 1%까지 혼입하는 경우 재생 SBR이 가진 충격 흡수 능력은 그대로 유지하면서, 인장강도를 향상시킬 수 있음을 확인하였다.

In this study, we report the microstructural evolution and shear strength of an Sn-Sb alloy, used for die attach process as a solder layer of backside metal (BSM). The Sb content in the binary system was less than 1 at%. A chip with the Sn-Sb BSM was attached to a Ag plated Cu lead frame. The microstructure evolution was investigated after die bonding at 330 °C, die bonding and isothermal heat treatment at 330 °C for 5 min and wire bonding at 260 °C, respectively. At the interface between the chip and lead frame, Ni3Sn4 and Ag3Sn intermetallic compounds (IMCs) layers and pure Sn regions were confirmed after die bonding. When the isothermal heat treatment is conducted, pure Sn regions disappear at the interface because the Sn is consumed to form Ni3Sn4 and Ag3Sn IMCs. After the wire bonding process, the interface is composed of Ni3Sn4, Ag3Sn and (Ag,Cu)3Sn IMCs. The Sn-Sb BSM had a high maximum shear strength of 78.2 MPa, which is higher than the required specification of 6.2 MPa. In addition, it showed good wetting flow.

This study divided the area capable of producing domestic forage into grazing pasture, hay production area, and silage crop area, calculated the required area according to the forage production volume, and examined whether self-sufficiency in forage leads to cost savings. When the self-sufficiency rate of forage for dairy cows and Hanwoo is 80%, the improvement in profitability per heaf ranges from 3% to 9%, typically around 5%, which is considered a significant benefit for both corporate and individual businesses. The average profit per ranch is expected to increase about KRW 50 million per year, and the country as a whole is expected to reduce forage costs by KRW 0.9 trillion per year. Recently, efforts are being made by the government and local authorities to cultivate summer forage at the rice fields for improving self-sufficiency in forage feed to stabilize rice supply and demand. Furthermore, it is also necessary to conduct research on reducing the cost of concentrated feed and TMR (Total mixed ration).

본 연구에서는 국내 아스팔트 도로 현장에서 발생한 동절기 도로융기 현상의 발생 원인을 현장 규명하고 동결융해 피해를 보수하고 자 현장조사, 현장 LFWD실험 및 포장 코어채취, 지하수위 측정, 기상데이터 및 설계자료 분석 등을 실시하였다. 본 연구의 동상 원인 분석은 추후 동결융해 피해 재발방지를 위한 적정한 보수보강공법을 선정하기 위해 수행하였다. 분석과정은 지하수위 상승에 의한 동 상피해 가능성, 동결깊이 과소설계에 의한 동결융해 가능성, 포장면 표면수 유입에 의한 동결융해 가능성, 도로 외측 비포장면을 통한 수분유입과 이에 의한 동결융해 가능성으로 조사하여 동상 원인을 파악하였다. 또한 현장에서 소형충격 재하시험 LFWD(Falling Weight Deflctometer)시험을 하여 포장의 구조적 지지력을 측정하여 얻은 처짐값을 통해 포장체 구조적 능력을 분석함과 동시에 도로융기와의 연관성을 파악하여 균열분석 결과를 함께 분석하고 보수방법을 제안하였다.

속도와 안전은 밀접한 관련이 있으며, 현재 국내에서는 속도 관리를 위해 제한속도를 설정하고 제한속도 기준에 맞춰 차량의 주행 속도를 단속하는 방식에 초점을 두고 있다. 하지만 도시부 보행자 안전 확보를 위해 차량이 제한속도 기준 외에 도로 구간에 따라 안 전하고 적절한 속도로 주행하도록 하는 안전속도의 모니터링이 필요한 상황이다. 본 연구에서는 이러한 안전속도의 범위 제시를 위해 사고 빈도 모형을 개발하고, 사고 빈도 모형에서 사고 빈도가 급격하게 변화하는 변곡점을 찾아 안전수준을 판단할 수 있는 임곗값으 로 설정하였으며, 설정된 임곗값을 기준으로 제한속도가 다른 두 도로 집단의 안전속도 범위를 제시하였다. 이 과정에서 대전시의 개 별차량 주행궤적 데이터를 수집 및 가공하여 모형의 입력변수로 활용하기 위한 속도 관련 안전성 평가지표를 산정하였으며, Dynamic threshold method 기반의 새로운 평가지표를 제안하였다. 또한, 속도 관련 안전성 평가지표뿐만 아니라 대전시 T-GIS에서 수집한 도로 시설물 데이터를 모형의 독립변수로 활용하여 도로 시설물을 고려한 안전속도 범위를 산정하고자 하였다. 안전속도 범위 도출 결과, 교차로와 횡단보도의 존재는 누적 사고 수와 양의 상관관계를 가졌으며, 사고 빈도 예측에서도 평균 주행 속도가 30km/h 이하로 낮은 경우 사고 빈도가 높게 추정되어 교차로 등 차량이 정지하는 상황과 첨두시와 같이 혼잡한 교통류 상황에서 차량이 안전하고 적절한 속도로 주행할 수 있도록 하는 안전관리 전략 수립이 필요함을 도출하였다. 본 연구에서 개발한 안전속도 범위 결정 방법론과 안전속 도 범위를 참고하여 도시부 속도 관리를 위한 교통안전 관리전략을 수립할 수 있을 것으로 기대한다.

In this study, we investigated the microstructure and piezoelectric properties of 0.96(K0.456Na0.536)Nb0.95Sb0.05-0.04 Bi0.5(Na0.82K0.18)0.5ZrO3 (KNNS-BNKZ) ceramics based on one-step and two-step sintering processes. One-step sintering led to significant abnormal grain (AG) growth at temperatures above 1,085 °C. With increasing sintering temperature, piezoelectric and dielectric properties were enhanced, resulting in a high d33 = 506 pC/N for one-step specimen sintered at 1,100 °C (one-step 1,100 °C specimen). However, for one-step 1,115 °C specimen, a slight decrease in d33 was observed, emphasizing the importance of a high tetragonal (T) phase fraction for superior piezoelectric properties. Achieving a relative density above 84 % for samples sintered by the one-step sintering process was challenging. Conversely, two-step sintering significantly improved the relative density of KNNS-BNKZ ceramics up to 96 %, attributed to the control of AG nucleation in the first step and grain growth rate control in the second step. The quantity of AG nucleation was affected by the duration of the first step, determining the final microstructure. Despite having a lower T phase fraction than that of the one-step 1,100 °C specimen, the two-step specimen exhibited higher piezoelectric coefficients (d33 = 574 pC/N and kp = 0.5) than those of the one-step 1,100 °C specimen due to its higher relative density. Performance evaluation of magnetoelectric composite devices composed of one-step and twostep specimens showed that despite having a higher g33, the magnetoelectric composite with the one-step 1,100 °C specimen exhibited the lowest magnetoelectric voltage coefficient, due to its lowest kp. This study highlights the essential role of phase fraction and relative density in enhancing the performance of piezoelectric materials and devices, showcasing the effectiveness of the two-step sintering process for controlling the microstructure of ceramic materials containing volatile elements.

This study aimed to investigate the relationship between the nutrition quotient and the dietary intake of adolescents. A total of 393 adolescents were surveyed to evaluate their Nutrition Quotient for Korean Adolescents (NQ-A) scores and dietary intake. The average age of the survey subjects was 15 years and the average NQ-A score of the subjects was 49.11±13.35. There was no significant difference in the NQ-A scores according to gender and age. The average dietary diversity score was 3.77±0.85, and it was significantly higher in boys than in girls (p< .05) with the scores of 12-14-year-old students being significantly higher than those aged 15-18 years (p< .01). The results of comparing the percentage of recommended intake or adequate intake and the mean adequacy ratio (MAR) according to the NQ-A grade, showed that the ‘High’ grade had a significantly higher intake percentage of vitamin B1, B12, folate, phosphorus, iron and a significantly higher MAR (p< .05). From a long-term perspective, efforts to improve dietary habits are deemed necessary to meet an individual’s nutritional requirements. Adolescents themselves should develop proper eating behaviors and acquire suitable dietary management skills to enhance their nutritional status, ultimately contributing to an improvement in their quality of life.

Wastewater management is increasingly emphasizing economic and environmental sustainability. Traditional methods in sewage treatment plants have significant implications for the environment and the economy due to power and chemical consumption, and sludge generation. To address these challenges, a study was conducted to develop the Intermittent Cycle Extended Aeration System (ICEAS). This approach was implemented as the primary technique in a full-scale wastewater treatment facility, utilizing key operational factors within the standard Sequencing Batch Reactor (SBR) process. The optimal operational approach, identified in this study, was put into practice at the research facility from January 2020 to December 2022. By implementing management strategies within the biological reactor, it was shown that maintaining and reducing chemical quantities, sludge generation, power consumption, and related costs could yield economic benefits. Moreover, adapting operations to influent characteristics and seasonal conditions allowed for efficient blower operation, reducing unnecessary electricity consumption and ensuring proper dissolved oxygen levels. Despite annual increases in influent flow rate and concentration, this study demonstrated the ability to maintain and reduce sludge production, electricity consumption, and chemical usage. Additionally, systematic responses to emergencies and abnormal situations significantly contributed to economic, technical, and environmental benefits.

This study investigated the effect of Lactiplantibacillus plantarum JSA22-fermented rice drinks on dextran sodium sulfate (DSS)-induced colitis in mice. Twenty-four mice were randomly assigned; No colitis (Con), colitis with tap water (DSS-only), colitis with unfermented rice (DSS-UFR), and colitis with fermented rice (DSS-FR). After inducing colitis with 2% DSS for 5 days, they were given Tap water, UFR drink, or FR drink for an additional 6 days. The DSS-FR group had significantly lower Disease Activity Index (DAI) scores compared to the DSS-only group, but no significant difference with the DSS-UFR group. Colon length was reduced in the DSS-only group. The DSS-only group had significantly higher IL-6 mRNA levels compared to the Con group, while the DSS-FR groups showed significantly lower IL-6 mRNA levels compared to the DSS-only group. These results suggest that rice drinks fermented with Lactiplantibacillus Plantarum JSA22 ameliorate the severity of DSS-colitis, by potentially reducing proinflammatory cytokines.

Recently, in newly constructed apartment buildings, the exterior wall structures have been characterized by thinness, having various openings, and a significantly low reinforcement ratio. In this study, a nonlinear finite element analysis was performed to investigate the crack damage characteristics of the exterior wall structure. The limited analysis models for a 10-story exterior wall were constructed based on the prototype apartment building, and nonlinear static analysis (push-over analysis) was performed. Based on the finite element (FE) analysis model, the parametric study was conducted to investigate the effects of various design parameters on the strength and crack width of the exterior walls. As the parameters, the vertical reinforcement ratio and horizontal reinforcement ratio of the wall, as well as the uniformly distributed longitudinal reinforcement ratio and shear reinforcement ratio of the connection beam, were addressed. The analysis results showed that the strength and deformation capacity of the prototype exterior walls were limited by the failure of the connection beam prior to the flexural yielding of the walls. Thus, the increase of wall reinforcement limitedly affected the failure modes, peak strengths, and crack damages. On the other hand, when the reinforcement ratio of the connection beams was increased, the peak strength was increased due to the increase in the load-carrying capacity of the connection beams. Further, the crack damage index decreased as the reinforcement ratio of the connection beam increased. In particular, it was more effective to increase the uniformly distributed longitudinal reinforcement ratio in the connection beams to decrease the crack damage of the coupling beams, regardless of the type of the prototype exterior walls.

The purpose of this study is to develop the protection of passengers in the event of a side collision with a school bus for children. Rub-rail is installed in the United States and other countries to protect the side of school buses for children to some extent. However, in the case of Korea, there are no safety devices to protect the side of school buses for children. Therefore, the FE model was analyzed to see if there is a difference depending on whether or not Rub-rail installed on school buses in the United States is applied, and whether it affects the damage to the human body. As a result, the maximum amount of intrusion at the point of collision differs depending on whether Rub-Rail is installed. It is expected that the evaluation results of IIHS for Rub-Rail may vary depending on the degree of intrusion.

In alignment with South Korea's “3020 Renewable Energy Expansion Plan,” this study focuses on the developing large-scale floating wind turbines. It addresses the challenges of increased size and cost in floating structures for wind turbines over 10MW. This paper details the preliminary design of a novel floating substructure utilizing composite materials(ie, EVA). Structural analysis was performed using ABAQUS, accounting for both typical and extreme wind conditions. Results from the analysis validate that the substructure design is adequately feasible for implementation.

이 연구의 목적은 내면화된 수치심이 정서표현 양가성과 자기자비의 조 절된 매개효과를 통해서 부부관계 진솔성에 영향을 미친다는 가설을 경험 적으로 검증하는 것이었다. 이를 위해, 기혼상태의 남녀 609명의 자기보고 자료를 수집하고 위계적 회귀분석 방법으로 검토하였다. 연구 결과, 내면화 된 수치심은 정서표현 양가성과는 통계적으로 유의미한 정적 상관을 보였 고, 자기자비 및 부부관계 진솔성과는 통계적으로 유의미한 부적 상관을 보였다. 또한 내면화된 수치심과 부부관계 진솔성의 관계를 정서표현 양가 성이 부분적으로 매개할 것이라는 가설 및 그 관계를 자기자비 수준이 조 절할 것이라는 가설이 모두 검증되었다. 이것은 내면화된 수치심과 부부관 계 진솔성의 관계에서 정서표현 양가성의 매개효과가 자기자비의 수준에 따라서 체계적인 차이를 보인다는 것을 시사하는 결과였다. 마지막으로 이 러한 발견의 임상적 시사점과 방법적 한계점을 논의하였다.

To understand the spatiotemporal distribution pattern of zooplankton and the environmental factors influencing zooplankton abundance in Gomso Bay, major harvesting area of Manila clam (Venerupis philippinarum) in South Korea, zooplankton sampling was conducted four times in autumn (October 2022), winter (January 2023), early spring (March 2023), and spring (May 2023). Among the environmental factors of Gomso Bay, water temperature, chlorophyll a concentration (Chl-a), dissolved oxygen (DO), and pH observed different patterns, while salinity and suspended particulate matter (SPM) showed no significant statistical differences between the survey periods. The zooplankton in Gomso Bay occurred 33, 29, 27, and 29 taxonomic groups during each respective survey period. In October 2022 and May 2023, arthropod plankton were dominated, while in January and March 2023, protozoa were primarily dominant. Among the Arthropods, copepods including Acartia hongi, Paracalanus parvus s. l., Corycaeus spp., and Oithona spp. commonly found along Korean coastal areas of the Yellow Sea, were dominated. Cluster analysis based on zooplankton abundance indicated a single community (stable condition) in each season, attributed to low dissimilarity distances, while three distinct clusters (autumn, winter-early spring, spring) between seasons indicated a highly seasonal environment in Gomso Bay.

This research aimed to examine the effects of grapefruit seed extract (GSE) at various concentrations on the microbial safety and physicochemical characteristics of onion puree (0.01~0.1%). The onion puree was kept at 4℃ for 14 days. The results of the study indicated that the addition of GSE did not cause any significant changes in the sample’s brix degree and viscosity in onion puree (p<0.05). However, as the concentration of GSE increased, the pH level decreased. On the other hand, as GSE was added, the lightness of the onion puree increased, while the redness and yellowness decreased. Compared to pure onion puree, the GSE-incorporated onion puree had higher levels of total flavonoid and total polyphenol content, indicating that it helps to maintain antioxidant activities. Based on the microbial safety test, aerobic bacteria, yeast, and mold were absent until day 14 of storage. In conclusion, the study suggests that the addition of GSE to onion puree increases its antioxidant activity and shelf-life.

This study investigated quality characteristics and antioxidant activity of beetroots after blanching. Beetroots were blanched in distilled water, 2% NaCl water, and 2% citric acid water at 100°C for 3 minutes (the blanched group). The moisture content was highest in the control (CON) at 91.30% (p<0.05), and cooking loss was lowest in the water-blanched beetroot (BW) at 5.39% (p<0.01). Chromaticity decreased after blanching compared to CON (p<0.001). Total polyphenol contents (TPC) and total flavonoid contents (TFC) decreased after blanching, and as a result of comparing the True retention (TR) of the blanching treatment group, BW had the highest with TPC TR 91.22% and TFC TR 70.51%. DPPH and ABTS+ radical scavenging activities were highest in the CON, and in the blanching group BW was highest scavenging activity. The total number of microorganisms in the CON group was 2.97 log CFU/g, whereas no microorganisms were detected in the blanched groups. Therefore, this study, blanching in water without additives is the most appropriate method for preserving physiologically active substances and nutrients in beetroots and inhibiting microbial growth.

This study investigated quality characteristics and functionality of rose sparkling wine that were manufactured by secondary fermentation after inoculation of yeast strains. The pH of the samples ranged from 3.96 to 4.05 and total acidity ranged from 0.23 to 0.32%. The alcohol contents of wines ranged from 6.4 to 6.6% and the CO2 pressure ranged from 2.0 to 2.6 bar. The brightness of rose wines ranged from 84.72 to 87.36, the redness from 9.28 to 14.15, and the yellowness from 9.50 to 19.20. The hue value of wines ranged from 1.137 to 1.513 and color intensity ranged from 0.724 to 0.882. Aroma analysis identified 14 alcohols, 22 esters, 4 ketones, 4 acids, and 17 miscellaneous compounds. The total tannin contents and total polyphenol contents of wines were 11.28~12.43 mg% and 24.79~28.20 mg%, respectively. The DPPH radical scavenging activity of wines ranged 63.33 to 67.89% and the ABTS radical scavenging activity of wines 82.16~86.06%. The results of this study provide a basis for establishing the brewing process of rose sparkling wines yeast strains.

This study was undertaken to provide basic data to aid product development and marketing by identifying purchasing behaviors and performing Important Performance Analysis (IPA) according to the consumption values of rice cakes. This study was conducted on 426 consumers who purchased rice cakes. Analysis was performed to determine general characteristics, consumption behaviors, preference for rice cakes, material preferences for rice cake development, need for rice cake development, and importance and satisfaction when selecting rice cakes. Cluster analysis classified consumption values into three clusters. The high and middle consumption value groups contained the greatest proportions of consumers aged over fifty. The high and medium consumption value groups preferred rice cakes more than the low consumption value group. Higher rice cake consumption value was positively associated with the greater preference for rice cakes. Furthermore, the perceived need to develop rice cakes was greatest in the high consumption value group. In addition, importance and satisfaction were positively associated with consumption value. IPA analysis showed that the attributes that require continuous attention because of their contributions to importance and satisfaction were taste, quantity, and hygiene. Different rice cake marketing and product development strategies are required for different consumption values.

To investigate the impact of forestry projects on the carbon stocks of forests, we estimated the carbon stock change of above-ground and soil before and after forestry projects using forest type maps, forestry project information, and soil information. First, we selected six map sheet with large areas and declining age class based on forest type map information. Then, we collected data such as forest type maps, growth coefficients, soil organic matter content, and soil bulk density of the estimated areas to calculate forest carbon storage. As a result, forest carbon stocks decreased by about 34.1~70.0% after forestry projects at all sites. In addition, compared to reference studies, domestic forest soils store less carbon than the above-ground, so it is judged that domestic forest soils have great potential to store more carbon and strategies to increase carbon storage are needed. It was estimated that the amount of carbon stored before forestry projects is about 1.5 times more than after forestry projects. The study estimated that it takes about 27 years for forests to recover to their pre-thinning carbon stocks following forestry projects. Since it takes a long time for forests to recover to their original carbon stocks once their carbon stocks are reduced by physical damage, it is necessary to plan to preserve them as much as possible, especially for highly conservative forests, so that they can maintain their carbon storage function.