In this study, computer simulation of the drawbridge structure was performed to verify the validity of the design and to evaluate its safety. For this, the follower bracket was modeled, and the parts of the follower bracket were connected using 1D elements. The boundary condition applied moments to the rotation shaft of the girder gear in the clockwise and counterclockwise directions, and the connection between the upper parts was modeled using 1D elements to model the bolted connection. In case of rotational shaft deformation, an analysis was performed on the displacement occurring in the structure during the opening/closing operation. As a result of structural analysis of the follower bracket for various cases, the stress at the connection was lower than the tensile strength and yield strength, so it was evaluated as safe. Through this, we intend to use it as a data that can identify anomalies.

In this study, the design of fuel tanks for SUVs (sports utility vehicles) was dealt with through structural analysis. Fuel tank analysis was performed to evaluate safety, and improvement plans for weak areas were found and reflected in the design. In addition, strength analysis and pressure analysis were performed in parallel to solve the problem of oil leakage around the lower part of the fuel tank and the rear mounting that occurred during the endurance test, and the analysis results were reflected in the design. As a result of analysis through various design changes, it was possible to present an appropriate reinforcement flange shape. In addition, when the thickness of the fuel tank was changed from 1.0mm to 0.8mm, the stiffness of the fuel tank decreased by approximately 30%, and reinforcement was required.

The sub-frame is located on the lower body of a monocoque type vehicle and serves as an engine and suspension, and is an important object part that receives a lot of load. The existing press-type sub-frame has a large number of parts for assembling, which causes an increase in cost. Changing the machining form of this part from the existing press-type machining method to the hydro-forming machining method has the advantage of reducing the cost and weight at the same time due to the reduction of the process. Therefore, in this study, the purpose of this study is to change the design so that the sub-frame of the existing press type can be changed to the hydro-forming process method. To this end, we intend to present a design method by analyzing the effect on the rigidity of the sub-frame using the existing machining method through shape optimization analysis.

Hydro-forming technology is a technology that will replace the existing press-forming technology and is used in various industry range from automotive parts to electronic products. The advantage of this technology is that it has dramatically changed the existing processing method, and it can be said that the process reduction due to the reduction of parts, cost reduction, and high precision are mentioned. In this study, it is intended to present a design process using computer simulation by changing the sub-frame for automotive parts produced with the existing press forming technology to the hide-forming method. To this end, it is intended to use it as part design data by comparatively analyzing the cross-sectional shape and thickness reduction, which are the major factors necessary to determine the successful development of the developed parts.

In order to satisfy the strengthening automobile exhaust gas regulation and CO2 regulation, the development of eco-friendly vehicles is actively progressing. To cope with these regulations, research on alternative fuel vehicles is being actively conducted. Alternative fuels are one of the best ways to reduce dependence on fossil fuels and respond to emissions and CO2 regulations. Natural gas, one of many alternative fuels, contains methane (CH4) as a main component and has abundant reserves, so it is attracting attention as a fuel that can provide stable long-term supply by replacing fossil fuels. In addition, natural gas has a high octane number, so there is room for improvement in combustion characteristics when used in SI engines, and it has the advantage of reducing harmful emissions and carbon dioxide (CO2) compared to conventional fossil fuels. When using a low-pressure injector in a turbo engine, it is difficult to secure the flow rate of fuel because the pressure difference between the injector and the manifold is small. Therefore, it is necessary to develop a high-pressure injector to improve this. Natural gas is a gaseous fuel and should be developed in consideration of compressible flow, Although the use of a CNG high-pressure injector is required, it is difficult to stabilize the flow due to the Mach disk and shock wave interference caused by compressible flow. If the flow is not stabilized, it is difficult to precisely control the flow. Therefore, it is necessary to develop an injector in consideration of flow characteristics. In this paper, the flow analysis according to the shape change of the injector was conducted to improve the fuel flow rate injected from the 800 kPa high pressure CNG injector.

The efficiency of the purchasing and procurement logistics is important in automotive industry. The rationalization of production system is directly impact on productivity and quality. For this reason importance of logistics is high. Despite we are continuously making effort, our country are still below the level than developed country on logistics efficiency. Rising labor costs is an important factor in increasing logistics costs. So workforce reduction in logistics department is a large part. We deal with A-company inbound logistics, especially procurement logistics in automotive logistics as research object. So in this study we do research on work load balance about workers. We do research on 1,475 kinds of components in procurement process. We applied work load balance algorithm on chassis, final, sequence, trim warehouses workers. According to number of workers and average M/H, algorithm is applied in two ways. After applied work load balance algorithm we reduced numbers of workers from 28 to 20 and improved worker load balance rate from 47.1% to 93.7%

Korean automobile industrial is in a difficult situation because of more competitive global market and lower demand. Therefore, domestic as well as global automobile manufacturers are making greater efforts in cost reduction to strengthen the competitiveness. According to statistical data, logistics cost in domestic manufacturers is higher than advanced countries. In this study, we developed program to effectively manage standard time of procurement logistics, and confirm based on A-automobile factory data. For the purpose, we develop the system which is possible to manage standard time as well as calculate man-hour. Program is not just for calculating and managing standard man-hour, scenarios analysis function will be added to calculate benefit while introduce logistics automated equipment. In this study we propose scenario using AGV instead of electric motor while move component. In the scenario analysis, job constitution is changed，and then we use system to compare the result. We can confirm standard man-hour is reduced from 22.3M/H to 14.3M/H. In future research, it is necessary scenario analysis function, and develop algorithm with realistic constraint condition.

Members of the Vps (Vacuolar protein sorting) protein family involved in the formation of the retromer complex have been discovered in a variety of species such as yeast, mouse, and human. A mammalian retromer complex is composed of Vps26, Vps29, and Vps35 proteins and plays and important role in cation-independent mannose-6-phosphate receptor retrieval from the endosome to the trans-Golgi network. In this study, we have identified the full-length sequences of the retromer components of Vps26, Vps29, and Vps35 in micro pigs. The cDNA sequences of these retromer components have been determined and the result showed there is 99% homology among the component counterparts from mouse, micro pigs, and humans. In addition, the retromer complexes formed with hetero-components were found in the brain of micro pigs. Based on above results, we suggest mammalian Vps components are well conserved in micro pigs.