Due to their fascinating properties, there is a rise in the critical consideration of carbon-based nanomaterials in a plethora of applications. Carbon nanomaterials, such as nanotubes, graphene, fullerenes, and nanodiamonds, have broad applicability and potential research prospects. In the past few years, the developments and consumption of still smaller nanomaterials, namely graphene quantum dots and carbon nanodots or carbon dots (CDs) have been explored. Since carbon as a component exhibits insignificant cytotoxicity and remarkable biocompatibility, CDs have found a wide scope of potential applications. Owing to their fascinating aspects, such as small size, biocompatibility, low toxic nature, environment-friendliness, costeffectiveness, ease of chemical functionalization, derivatization and surface modification, and photoluminescence tenability, CDs have been widely acknowledged. CDs have found major prospects in the areas of catalysis, sensors, and optical and bio-related applications. CDs are generally synthesized by employing techniques of pyrolysis, laser ablation, arc discharge, electrochemical method; hydrothermal and solvothermal techniques; and microwave and ultrasonic irradiations. This review article presents a brief account of the major properties of CDs, and applications, with particular emphasis on the green and environment-friendly synthesis methodologies. An overview of the microwave and ultrasound irradiation-induced syntheses for the preparation of CDs is presented in the light of green chemistry principles. In addition, some of the green and environmentally benign precursors for the production of CDs are outlined. The most recent work on CDs is included in this review article.

In this study, we report a controlled one-pot green synthesis of multiwalled carbon nanotubes (MWCNTs) via pyrolysis of sustainable agriculture waste (chickpea peel) at 400 °C in aqueous medium. These MWCNTs demonstrated 7.0 nm diameter, 0.28 nm graphitic spacing with carbonyl, hydroxyl, and carboxylic acid functionality. The D band (presence of sp3 defects) and G band ( E2g mode of graphite) at 1350 cm−1 and 1580 cm−1 originated in Raman spectrum, respectively. The prepared MWCNTs showed blue fluorescence with 10% fluorescence quantum yield in aqueous medium. The MWCNTs showed triple exponential decay characteristics with an average fluorescence lifetime of 4.7 ns. The synthesized MWCNTs revealed a consistent fluorescence in the cytoplasm of 22RV1 human prostate carcinoma cell line without exerting any sign of cytotoxicity. The MWCNTs also exhibited remarkable cytocompatibility in human immortalized prostate epithelial RWPE1 cells.

The aim of this paper is to give insights on the role and persuasive power of metaphor in political communication. The current paper imbibes the study of conceptual metaphors in two different forms which are the lifeline of politics, that is: election campaigns and projection of Prime Minister and the nation to a global audience. For analysing the role of metaphor, while addressing an international audience, we have picked up some famous speeches of Indian PM Modi which he pitched at several national and international forums immediately after being elected as Prime Minister. For studying election campaign communication we have examined the text of newspaper articles and the trending social media updates. We have analyzed the text using Lakoff and Johnson’s Conceptual Metaphor Theory. Some famous conceptual metaphors are analysed, such as war, nature, nation as person/body/family and the world as a community. In a valuation of public speeches, we found that speech which addressed general public has double the metaphors than those addressing limited audiences. Metaphors allow the worldwide public to grasp the meanings of political events and feel a part of the performance. They are also effective because of their ability to resonate with latent symbolic representations residing at the unconscious level.

Isroaniso matrix precursor synthesized from commercially available petroleum pitch was stabilized in air. The influence of oxygen mass gain during stabilization on the yield of matrix precursor was studied. Additionally, the influence of pressure on the yield of the stabilized matrix precursor in a real system was studied. The fourier transform infrared spectrometry (FTIR), thermogravimetric analysis (TGA), yield, yield rate, and yield impact were used to check the effect of stabilization and pressure on the yield of the matrix precursor and the end properties of the composite thereafter. The results showed that the yield increased with stabilization duration up to 20 h whereas it decreased for stabilization duration beyond 20 h. Further results showed that the stabilized matrix precursor for a duration of 5 h could withstand almost two-fold greater hot-pressing pressure without resulting in exudation as compared to that of a 1 h stabilized matrix precursor. The enhanced hot-pressing pressure significantly improved the yield of the matrix precursor. As a consequence, the densification and mechanical properties were increased significantly. Further, the matrix precursor stabilized for a duration of 20 h or more failed to provide proper and uniform binding of the reinforcement.

Ground Level Enhancements (GLEs) in cosmic ray intensity observed during the period of 1997-2012 have been studied with energetic solar features and disturbances in solar wind plasma parameters and it is seen that all the GLEs have been found to be associated with coronal mass ejections, hard X-ray solar ares and solar radio bursts. All the GLEs have also been found to be associated with sudden jumps in solar proton ux of energy of ≥ 60 Mev. A positive correlation with correlation coefficient of 0.48 has been found between the maximum percentage intensity (Imax%) of Ground Level Enhancements and the peak value of solar proton ux of energy (≥ 60Mev). All the Ground Level Enhancements have been found to be associated with jumps in solar wind plasma velocity (JSWV) events. A positive correlation with correlation coefficient of 0.43 has been found between the maximum percentage intensity (Imax %) of Ground Level Enhancements and the peak value of solar wind plasma velocity of associated (JSWV) events. All the Ground Level Enhancements have been found to be associated with jumps in solar wind plasma pressure (JSWP) events. A positive correlation with correlation coefficient of 0.67 has been found between the maximum percentage intensity (Imax %) of Ground Level Enhancements and the peak value of solar wind plasma pressure of associated (JSWP) events and of 0.68 between the maximum percentage intensity (Imax %) of Ground Level Enhancements and the magnitude of the jump in solar wind plasma pressure of associated (JSWP) events.

In all conventional sintered PM products, the pores present are of two types, primary and secondary. Primary pores forming during compaction and latter during sintering, due to penetration of formed liquid through the matrix grain boundary. Effect of carbon addition on diffusion of Cu in SH737-2Cu system was investigated. After compaction and transient liquid phase sintering at and , samples were characterized for densification, showing rise in sintering density and reduction in swelling on carbon addition. Quantitative microstructural characterization (shape factor and pore size) revealed bimodal distribution for 0% carbon, more rounded pores for 0.9% carbon and higher sintering temperature, and pore coarsening at higher sintering temperature.

The study examines hardness pattern of SH737-2Cu-.9C samples transient liquid phase sintered at different temperatures viz. , and , heat treated by various methods and then tempered at different temperatures. Sintered samples were characterized for density and densification parameter, and austenitized at , subsequently cooled by four different methods viz. annealing, normalizing, oil and brine quenching. Hardness pattern was found minimum for air cooled and maximum for brine quenched, and samples sintered at had relatively higher hardness. The O.Q and B.Q samples were then tempered at , , and . Hardness pattern typically showed secondary hardness taking place, with maximum around .

Influence of temperature, relative humidity, spore washing and spore drying on conidial germination of Alternaria porri(Ell.) Cif. was studied. Maximum conidial germination occurred at 100% relative humidity prevailing for 6 hours or more at . Conidial germination decreased with increase in number of spore washings. Drying of conidia for more than half an hour caused significant decrease in germination. In all the experiments, conidial germinatio increased with increase in incubation period.