This paper analyzed structural behaviors of the staggered truss system, typically used in low seismicity regions, resisting the lateral loads such as wind and seismic load. A comparative study of cost and efficiency was carried out by analysing and designing the 10- and 20-story buildings with various types of truss, including pratt, howe, warren, K-, and vierendeel, which may typically be used in staggered truss system. In design, column and truss members are selected in group, and the efficiency of the member design was judged by average demand capacity ratio of the all members in same group. And economic analysis of the system was investigated by the quantity of the structural members. As a result, staggered truss system with the pratt truss and warren truss showed the most economical and efficient performance for 10-story building, and 20-story building, respectively.

In the present study, the structural and fatigue analysis on the shape change of an automatic press are investigated for prediction of operation safety and reliability of the automatic press along the thickness(t) and length(L) of head, and corner shapes(case 1, 2, 3). The equivalent stress and deformation characteristics of the automatic press were studied by computerized analysis method for the bushing production of the seat frame. An external stress of 14.0 MPa was applied to predict the operation stability and the fatigue limit of the structure. As the thickness of the header increased and the length of the header decreased, the load stability applied by the piston improved and the maximum stress and deformation were reduced. In addition, due to the change in shape of the corners, the load applied at the cross-sectional area of the corners decreases, and then the maximum stress and deformation appearing in the header are reduced. That is, the change of corner shapes affects the equivalent stress and deformation. That is the change of corner shapes affects the equivalent stress and deformation. From the fatigue and vibration analysis, fatigue failure does not occur even when the number of alternating operation of the automatic press increases, and the natural frequency is predicted for dynamic characteristics.

Shape analysis ought to be emphasized in the teaching of Chinese characters. The primary methods to analyze the form of Chinese characters are incarnated in ShuoWenJieZi includeing analysis on component function, analysis on form variation and analysis on isomorphic part, all of which afford us as references that merit academic attention in modern teaching of Chinese characters. The paper introduces the method of structure analysis from ShuoWenJieZi, focusing on how to draw lessons from these approaches in the teaching of Chinese characters and illustrating key points in practical application as well as effects that may achieve.

As the size of the wind power becomes larger, the development of the assembly type wind power which is advantageous in transportation and installation is active. This advantage comes from the economic point of view, and the stiffener is applied to the inner side, so that the safety is high. Large wind power require door openings for maintenance. The door opening has an irregular cross-section, and an excessive stress active due to the door opening. In this paper, the stresses occurring around the door opening was analyzed. As a result, small stress values were appeared in the tower, as the number of stiffeners were increased. Also, stress values were decreased a little in the tower as the opening shape become to ellipse was closer.

The object of research in Based on 1.5MW wind turbine blade. This paper has carried out the aerodynamic shape optimization design of wind turbine blade. Based on the aerodynamic basic theory of wind turbine blade design and combined with particle swarm optimization algorithm, the design optimization model of the aerodynamic shape of blade is established. The calculation programs are written by use of MATLAB and calculate chord length and torsion angle of the blade. Then the shape of wind turbine blade is obtained. As research we can know that the chord length is decreased after optimization design of wind turbine blade, The optimized blade not only meets the actual manufacturing requirement, but also has the largest wind energy utilization coefficient.

A press which has a 20 percent share in machine tools is one of the production facilities. Recently hydraulic press is used to reinforce competitiveness of the manufacturing industry. The press by using metal powder makes products without additional process while conventional processing machine makes products after removing unnecessary parts. In this way, large quantity of products can be produced in a short time. Researches to manufacture products by the press have been proceeding after 1970. In this study, structure and displacement analysis for shape parameters for punch used as the component for hydraulic press was investigated and structural stability was identified based on the results.

Carbon fiber reinforced plastics are typical examples of carbon fiber, which retain high strength and high strength at high temperatures. Also, it is applied to various fields, such as the structure of the aircraft, automobile, and the core industries. CFRP machining methods include machining tools such as cutting machining and laser machining. In this thesis, a tool dynamometer and tool microscope were used to measure the cutting characteristics of various cutting conditions and tool wear and tool wear. As a result, the cutting force of the new shape drill (lower shape drill) was measured higher than other tools, the amount of tool wear was the lowest, and it was found that a good machined surface was obtained.

We synthesized potassium hexatitanate, (K2Ti6O13, PT6), with a non-fibrous shape, by acid leaching and subsequent thermal treatment of potassium tetratitanate (K2Ti4O9, PT4), with layered crystal structure. By controlling nucleation and growth of PT4 crystals, we obtained splinter-type crystals of PT6 with increased width and reduced thickness. The optimal holding temperature for the layered PT4 was found to be ~920 oC. The length and width of the PT4 crystals were increased when the nucleation and growth time were increased. After a proton exchange reaction using aqueous 0.3 M HCl solution, and subsequent heat treatment at 850 oC, the PT4 crystal transformed into splinter-type PT6 crystals. The frictional characteristics of the friction materials show that as the particle size of PT6 increases, the coefficient of friction (COF) and wear amounts of both the friction materials and counter disc increase.

Numerical analysis using k-ε model of unsteady state was performed to decide the optimal shape of power auxiliary apparatus in automotive engine. In order to obtain auxiliary electric power using coolant in automotive engine, shapes of 3 Types were compared. Furthermore to achieve the confidence of numerical analysis, the results of numerical analysis was compared with those of experiment. As the results, it showed that accuracy of numerical analysis was about 85~98%. Further the optimal shape, in this study, was Type-1, which had outer rounding R32.5, among 3 Types.

In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here it was compared with the pipe type and labyrinth type orifice cross-section. The second study is for optimized piston structure development by comparison pipe orifice and labyrinth orifice. Consequently, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. The result of optimized piston structure development through experiment is fixed orifice specification as labyrinth orifice because pipe orifice is founded slip up/down phenomenon of the Ø0.4~1.0 orifice and the labyrinth orifice is not founded that of the Ø0.4~0.6 orifice both tests on 300 mm intervals.

본 연구에서는 케이블교량에 사용되는 보강거더의 형식 중에서 2에지거더를 대상으로 거더형상의 변화에 따른 정/동적 풍응 답특성을 풍동실험을 통하여 고찰하였다. 하부거더의 단면형상은 I형, 사다리꼴 2종류, 5각형 2종류 및 원형(I)으로 총 6종류를 채택하 였고 변장비는 1:5로 하였다. 본 연구에서 얻어진 결과로서, 정적설계에 사용되는 항력계수의 경우 원형단면과 5각형단면이 다른 단면에 비하여 유리한 것으로 나타났다. 대상단면의 동적안정성은 모두 비틀림 플러터가 지배적이고 플러터 한계풍속은 영각증가에 따라 급격히 감소하는 경향을 나타냈으며, I형 단면과 비교할 때 5각형단면과 원형단면의 한계풍속은 증가하는 것으로 확인되었다. 와류진 동의 최대진폭은 전반적으로 (+)영각범위에서는 영각증가와 함께 증가하였으나 (-)영각범위에서는 증감폭이 두드려지지 않는 경향을 보였으며 단면형상변화에 대해서는 사다리꼴 > 5각형 > 원형의 순으로 진폭이 감소하였다. 소정의 평균풍속에 대한 정적변위를 조사 하였으며 연직변위의 경우 모든 단면에서 영각증가에 따라 증가하였고 비틀림변위는 (-)영각범위에서는 큰 변화가 없으나 (+)영각범위 에서는 영각증가와 함께 정적변위가 감소하였고 5각형단면인 P2가 가장 작은 값을 보였다. 본 연구에서 수행된 정/동적 응답실험결과 를 비교분석한 결과, 5각형단면인 P2단면과 원형단면의 내풍성이 우수한 것으로 나타났다.

예부선이 항행할 경우 부선의 회두운동으로 인하여 예선은 조종성능에 제한을 받기 때문에 부선의 회두운동을 감소시켜야 안전한 예항업무를 이행할 수 있다. 본 연구에서는 부선의 침로안정성을 향상시키기 위한 방안으로 부선의 회두운동에 영향을 미치는 항목들을 조사하기 위하여 수조실험을 실행하였다. 선수 형상에 따라 회두운동 특성이 다르게 나타나기 때문에 서로 다른 선수 형상을 지닌 부선 모델을 대상으로 스케그의 영향, 예인선속의 영향, 예인삭 길이의 영향, 브라이들의 영향에 대하여 종합적으로 분석하였다. 실험결과 스케그의 설치 위치에 의한 효과는 선수형상에 따라서 다르게 나타나고 있는 모습을 보여주고 있다. 부선의 회두운동은 부선에 연결된 예인삭의 길이가 길수록 부선의 회두가 작아짐을 알 수 있었다. 또한 예인삭만 연결한 상태보다 예인삭에 브라이들을 연결하는 것이 부선의 회두가 작아지며, 브라이들의 길이가 길어질수록 부선의 회두운동이 크게 작아짐을 알 수 있었다.

디젤엔진에서는 2차 분사 시스템은 다양한 배기 시스템에 적용이 가능하고, 엔진 제어와 관계없이 독립적으로 제어가 가능하기 때문에 환원제 희석 면에서도 후분사 또는 다른 농후한 환원제 분위기 형성 방법 등에 비해 장점이 많다. 2차 분사 시스템에서는 환원제의 공급 방법에 따라서 촉매의 효율은 달라질 수밖에 없다. 환원제는 일정압력 이상으로 유지 및 최적화가 필요하고, 인젝터의 위치 및 각도의 선정은 매우 중요한 인자이다. 본 논문에서는 2차 분사 조건을 변화시켜 환원제의 농도와 양을 변화시켰다. De-NOx 촉매 시스템에서 최대의 NOx 정화 효율에 적합한 환원제 분사 조건들의 선정이 필요하고, 분무 도달거리, 분무 평균 입경, 분무각, 분사량 등의 분무 특성과 환원제의 균일 분포를 잘 파악하여야 한다. 이와 같은 목적을 위하여 2차 분사에서 충돌판 형상에 의한 분무 및 거동 특성은 가시화 방법과 디지털 화상 처리 기법을 사용하여 분석하였으며, 충돌판 형상의 영향성과 각 형상에 대한 최적 각도 범위를 도출하였다.

Early-type galaxies (ETGs) are supposed to follow the virial relation M = ke2 Re=G, with M being the mass,  being the stellar velocity dispersion, Re being the eective radius, G being Newton's constant, and ke being the virial factor, a geometry factor of order unity. Applying this relation to (a) the ATLAS3D sample of Cappellari et al. (2013) and (b) the sample of Saglia et al. (2016) gives ensemble- averaged factors hkei = 5:15  0:09 and hkei = 4:01  0:18, respectively, with the dierence arising from dierent denitions of eective velocity dispersions. The two datasets reveal a statistically signicant tilt of the empirical relation relative to the theoretical virial relation such that M / (2 Re)0:92. This tilt disappears when replacing Re with the semi-major axis of the projected half-light ellipse, a. All best-t scaling relations show zero intrinsic scatter, implying that the mass plane of ETGs is fully determined by the virial relation. Whenever a comparison is possible, my results are consistent with, and conrm, the results by Cappellari et al. (2013). The difference between the relations using either a or Re arises from a known lack of highly elliptical high-mass galaxies; this leads to a scaling (1-) / M0:12, with  being the ellipticity and Re = a p 1 - . Accordingly, a, not Re, is the correct proxy for the scale radius of ETGs. By geometry, this implies that early-type galaxies are axisymmetric and oblate in general, in agreement with published results from modeling based on kinematics and light distributions.

In women’s clothing the shoulders are distorted and exaggerated. Consequently, the wearers’ bodies are transformed and interpreted according to modern standards. We therefore refer to this aspect of women’s clothing as the power shoulder. This study aims to analyze the differences in sensibility images on variations in the shoulder shape of power shoulder jackets. Nine samples were examined that involved combinations of three variations of the shoulder height and three variations of the shoulder width. The data was evaluated by 123 fashion design majors. Four factors were selected: attractiveness, personality, activity, and self-respect. Among these factors, attractiveness is the most important. The study results indicated that changes in shoulder height acted as a major effect that had an independent influence on all four factors. In contrast, changes in shoulder width acted as a major effect that had an independent influence on attractiveness, personality, and activity but not on self-respect. It also had an influence on the interaction effect of attractiveness, personality, activity, and self-respect. We anticipate that this study will help individual customers select clothing that is suitable for their preference and body shape because it is now possible for them to estimate images of power shoulder jackets.

본 논문에서는 Co-Rotational plane beam transient analysis EDISON program(CR-보)를 이용한 에어포일 단면형상 변화 에 따른 진동특성 연구를 수행하였다. Co-Rotational 평면 보 해석은 대 회전과 작은 변형률을 갖는 보 해석에 적합하다. 항 공기의 날개를 외팔보로 가정하여, VABS를 통한 단면해석과 Fourier 변환을 통해 각 단면형상 변화에 따른 에어포일의 고 유진동수를 비교하였다. VABS를 사용하여 단면의 형상과 재료의 적층 정보를 고려한 단면에서의 유한요소 해석을 수행하 였다. 에어포일의 재질, spar 유무, 단일 등방성 재료·복합재료, 에어포일 최대두께의 변화에 따라 에어포일의 끝단 진폭과 고유진동수가 변화함을 확인할 수 있었다. 이를 바탕으로 에어포일 고유진동수 변화는 2차 관성모멘트/단면적, 밀도, 영률의 변화에 상당한 영향을 받음을 알 수 있었다.

본 연구에서 개발된 자동천공기는 콩의 재식밀도를 고려한 비닐 천공능력이 작업주행속도 0.18- 0.28m/s 조건에서 콩의 주간거리 0.20m, 0.25m, 0.30m에 대해 각각 320-500m2/h, 260-400m2/h, 210-330m2/h의 범위로 나타났다. 천공율은 칼날과 지면간 30mm 거리에서 비닐이 100% 천공되었으 며, 50mm 거리에서 원형칼날 16.7-25.2%, 사각칼날 33.0-42.3%, 육각칼날 54.5-100.0% 범위에서 천공되었다. 또한, 육각칼날 60°에서 비닐 절단면이 매끄럽고 부드러워 절단품질이 가장 우수하였다.