In this study, high temperature wetting analysis and AZ80/Ti interfacial structure observation are performed for the mixture of AZ80 and Ti, and the effect of Al on wetting in Mg alloy is examined. Both molten AZ80 and pure Mg have excellent wettability because the wet angle between molten droplets and the Ti substrate is about 10° from initial contact. Wetting angle decreases with time, and wetting phenomenon continues between droplets and substrate; the change in wetting angle does not show a significant difference when comparing AZ80-Ti and Mg-Ti. As a result of XRD of the lower surface of the AZ80-Ti sample, in addition to the Ti peak of the substrate, the peak of TiAl3, which is a Ti-Al intermetallic compound, is confirmed, and TiAl3 is generated in the Al enrichment region of the Ti substrate surface. EDS analysis is performed on the droplet tip portion of the sample section in which pure Mg droplets are dropped on the Ti substrate. Concentration of oxygen by the natural oxide film is not confirmed on the Ti surface, but oxygen is distributed at the tip of the droplet on the Mg side. Molten AZ80 and Ti-based compound phases are produced by thickening of Al in the vicinity of Ti after wetting is completed, and Al in the Mg alloy does not affect the wetting. The driving force of wetting progression is a thermite reaction that occurs between Mg and TiO2, and then Al in AZ80 thickens on the Ti substrate interface to form an intermetallic compound.

Angelica gigas Nakai (A. gigas) easily changes its color during storage, and appropriate thermal treatment can improve storage stability through inactivation of enzymes such as polyphenol oxidase. Therefore, this study was performed to determine quality characteristics of dried A. gigas in response to high-temperature-short-time (HTST) treatment during storage. Dried A. gigas were treated at 120-180℃ for 10 min, the samples were stored at 4℃ and 50℃ for 10 weeks, and used for the analysis of qualities. Concerning the color values, the sample treated at 120℃ was similar to the control, and the color change was large when treated above 180℃. However, color difference (△E* ab) was lower in treated samples than in control. Browning index was similar for all the samples except for the sample treated at 180℃. Functional qualities (phenolics content, antioxidant activities, and level of major components) showed a slight difference according to storage periods in all samples without control, and nodakenin content was observed in control. The results of this study showed that HTST treatment improved storage stability such as stability of colors and browning index in dried A. gigas during storage, and the appropriate treatment temperature was 120℃ in terms of stability in color and browning index.

SiC is a material with excellent strength, heat resistance, and corrosion resistance. It is generally used as a material for SiC invertors, semiconductor susceptors, edge rings, MOCVD susceptors, and mechanical bearings. Recently, SiC single crystals for LED are expected to be a new market application. In addition, SiC is also used as a heating element applied directly to electrical energy. Research in this study has focused on the manufacture of heating elements that can raise the temperature in a short time by irradiating SiC-I2 with microwaves with polarization difference, instead of applying electric energy directly to increase the convenience and efficiency. In this experiment, Polydimethylsilane (PDMS) with 1,2 wt% of iodine is synthesized under high temperature and pressure using an autoclave. The synthesized Polycarbosilane (PCS) is heat treated in an argon gas atmosphere after curing process. The experimental results obtain resonance peaks using FT-IR and UV-Visible, and the crystal structure is measured by XRD. Also, the heat-generating characteristics are determined in the frequency band of 2.45 GHz after heat treatment in an air atmosphere furnace.

기후변화에 대비하여 고온성 양송이 백색 품종을 육성한 결과는 다음과 같다. 모본은 KMCC00540, KMCC00591, KMCC00643을 선발하였고, ISSR과 SSR마커로 각각 동 핵균주를 선발하여 교잡하였다. 선발 교잡주를 고온 20~25 o C, 습도 80% 이상에서 3반복으로 재배하여 농업적 형질과 자실체 특성의 변이가 가장 적은 것은 Abs4-2016- 121 계통이었다. 이 계통은 KMCC00000와 KMCC0000를 교잡한 계통이며, 경주와 부여 농가에서 현장실증시험결과 Abs4-2016-121 계통이 자실체 경도가 높으며 고온에서 갓 개열이 지연되어 고온성 품종 ‘하담’으로 육성하였다.

신품종 감자 ‘아리랑1호’는 농촌진흥청 국립식량과학원 고령지농업연구소에서 2018년도 육성되었다. ‘아리랑1호’는 ‘Frontier’ 품종을 모본으로 하고 ‘대관1-117호’ 계통을 부본으로 2011년 교배하여, 장일 고온 조건에서 식물체 생육 및 괴경의 형성과 비대가 양호하여 다수확 할 수 있는 계통으로 선발되었다. 중앙아시아(여름재배)와 국내 평난지(강릉, 봄재배) 및 고랭지(대관령, 여름재배)에서 2014~2015년 생산력 검정을 통해 ‘대관1-150호’로 계통명을 부여하고, 2016~2018년 지역 적응성검정 시험을 거쳐 ‘아리랑1호’로 명명하였다. ‘아리랑1 호’의 초형은 반직립형으로서 초세가 강하고 왕성하다. 괴경모 양은 짧은 계란형이며, 괴경 색깔은 표피와 육질부 모두 황색이다. ‘아리랑1호’의 경장은 67.1 cm로 대조품종인 ‘수미’, ‘산테’보다 긴 반면, 경수는 3개 내외로 대조품종과 유사하다. 주당 괴경수는 9.0개로 ‘수미’(5.4개) 보다 많은 반면, ‘산테’ (14.1개)보다 적다. 괴경당 평균 무게와 포기당 총 괴경중은 각 각 96.1 g 및 865 g으로서 대조품종보다 무겁다. 겹둥근무늬병 과 역병에 대하여 중도저항성이며, 바이러스병과 더뎅이병에 있어서는 감수성을 나타낸다. 건조에 대한 저항성은 ‘산테’나 ‘수미’보다 강한 중도저항성으로 평가되었다. 비중과 건물율은 ‘수미’보다 높고 ‘대서’와 유사하며, 감자칩 품질은 ‘대서’와 같이 우수한 것으로 평가된다. ‘아리랑1호’의 단위면적당 상서수량은 국내의 경우 3,360 kg·10a-1으로 ‘수미’ 보다 57% 더 많 고, 중앙아시아에서는 3,070 kg·10a-1으로 ‘산테’ 보다 약 55% 더 많았다. 신품종 감자 ‘아리랑1호’는 장일 고온 건조한 지역에서 기형, 이차생장 등이 적고 다수성을 나타내어 중앙아시아 등 해외 진출에 유망한 품종으로 판단된다.

The high-temperature stability of YSZ specimens fabricated by die pressure and cold isostatic press (CIP) is investigated in CaCl2-CaF2-CaO molten salt at 1,150 °C. The experimental results are as follows: green density 46.7 % and 50.9 %; sintering density 93.3 % and 99.3 % for die press and CIP, respectively. YSZ foremd by CIP exhibits higher stability than YSZ formed by die press due to denseness dependency after high-temperature stability test. YSZ shows peaks mainly attributed to CaZrO3, with a small t-ZrO2 peak, unlike the high-intensity tetragonal-ZrO2 (t-ZrO2) peak observed for the asreceived specimen. The t-ZrO2 phase of YSZ is likely stabilized by Y2O3, and the leaching of Y2O3 results in phase transformation from t-ZrO2 to m-ZrO2. CaZrO3 likely forms from the reaction between CaO and m-ZrO2. As the exposure time increases, more CaZrO3 is observed in the internal region of YSZ, which could be attributed to the inward diffusion of molten salt and outward diffusion of the stabilizer (Y2O3) through the pores. This results in greater susceptibility to phase transformation and CaZrO3 formation. To use SOM anodes for the electroreduction of various metals, YSZ stability must be improved by adjusting the high-density in the forming process.

A gasketed plate heat exchanger(GPHE) requires a much smaller installation space than a shell & tube heat exchanger because of its compact and good thermal performances. However, GPHEs have a disadvantage of being relatively vulnerable to high temperature and pressure due to rubber gaskets. To overcome a GPHEs’ disadvantage, Welded Block type Plate Heat Exchangers(WBPHE) have been developed. The flow pattern and heat transfer principle of WBPHE are very similar to GPHEs, so they are very compact and can be applied to high temperature and pressure. In this study, the structure and characteristics of WBPHE are briefly introduced, and its thermal performances were conducted experimentally using hot and cold water in the Reynolds number’s range from 5,500 to 10,000. Test results were compared with the experimental correlations of other researchers, which shows that significant deviations were noticed in the heat transfer coefficient predictions with a deviation range from 31% to 85%. The previous friction factor correlations also predicted the current results with big errors from 25% to 45%. These deviations are expected to be due to different chevron angles between previous studies and the current study, and also the end-plate effect is expected to be one of the potential causes that led to these deviations.

억새와 같은 초본계 바이오매스로부터 cellulose, hemicellulose, lignin 등 주요성분을 추출하기 위해서는 알칼리 전처리가 효율적이며, 본 연구에서는 수산화칼륨(KOH)을 이용한 전처리 조건을 최적화하였다. 전처리 변수의 최적화는 반응표면분석법(RSM)을 적용하였다. RSM의 변수는 3개였으며, 변수범위는 각각 KOH 0.2∼0.8M, 반응온도 110∼190℃ 및 반응시간 10∼90min 이었다. 억새의 알칼리 전처리를 위한 최적조건은 KOH 농도 0.47M, 반응온도 134℃ 및 반응시간 65min 이었다. 최적 전 처리 조건에 따라 전처리를 수행한 후 고형물의 cellulose 함량은 66.1±1.1% 이었으며, hemicellulose 및 lignin 함량은 각각 26.4±0.4%, 3.7±0.1% 이었다. RMS 모델식에 따라 계산된 예측값은 실제값 대비 95% 범위 내에서 유효하였다. 최종적으로 전처리물을 동시당화발효를 통해 검증한 결과 에탄올 생산 수율은 96% 이었다.

This study was performed to investigate the effect of heat-stressed environment on rumen microbial diversity in Holstein cows. Rectal temperature and respiration rate were measured and rumen fluid was collected under normal environment (NE; Temperature humidity index (THI)=64.6) and heat-stressed environment (HE; THI=87.2) from 10 Holstein cows (60±17.7 months, 717±64.4 kg) fed on the basis of dairy feeding management in National Institute of Animal Science. The rumen bacteria diversity was analyzed by using the Illumina HiSeq™ 4000 platform. The rectal temperature and respiratory rate were increased by 1.5ﾟC and 53 breaths/min in HE compared to that in NE, respectively. In this study, HE exposure induced significant changes of ruminal microbe. At phylum level, Fibrobacteres were increased in HE. At genus level, Ruminococcaceae bacterium P7 and YAD3003, Butyrivibrio sp. AE2032, Erysipelotrichaceae bacterium NK3D112, Bifidobacterium pseudolongum, Lachnospiraceae bacterium FE2018, XBB2008, and AC2029, Eubacterium celulosolvens, Clostridium hathewayi, and Butyrivibrio hungatei were decreased in HE, while Choristoneura murinana nucleopolyhedrovirus, Calothrix parasitica, Nostoc sp. KVJ20, Anabaena sp. ATCC 33047, Fibrobacter sp. UWB13 and sp. UWB5, Lachnospiraceae bacterium G41, and Xanthomonas arboricola were increased in HE. In conclusion, HE might have an effect to change the rumen microbial community in Holstein cows.

3D 프린팅의 적층제조를 위한 시멘트 모르타르의 이용은 시멘트의 유동 특성을 개질하기 위한 시멘트 혼화용 폴리 머의 혼입이 필수적이다. 시멘트 모르타르는 점성이 높고 수축이 크기 때문에 적층제조를 위해서는 유동성, 경화속도, 시공성 및 적층특성의 개선이 필요하다. 시멘트 혼화용 폴리머 디스퍼젼을 혼입한 시멘트 모르타르는 시멘트 수화물과 공극 사이에 폴 리머 필름이 상호 형성되어 인장강도와 취성이 개선되며 우수한 접착성, 기밀성, 내약품성을 보인다. 최근, 사용편리성이 우수한 Ethylene-vinyl acetate 재유화형 분말수지가 널리 사용된다. 하지만 화재와 같은 고온에서는 재유화형 분말수지를 혼입한 경우에 는 성능저하가 더 크다. 재유화형 분말수지가 시멘트 수화물과 공극에 폴리머 필름을 형성하고 충전하지만 고온에 의해 열분해 되기 때문이다. 본 연구에서는 3D 프린팅의 적층제조를 위해 내열성이 개선된 Ethylene-vinyl chloride 재유화형 분말수지의 혼입률을 달리하여 고온에서의 특성과 열분해에 따른 공극특성을 검토하였다. 연구결과, EVCL 재유화형 분말수지를 혼입한 경우 고온에서 약간의 성능개선을 보였지만 열분해하여 공극률이 커지며, 밀도, 강도가 감소한다. 따라서, 사용조건에 적합한 배합조절 등이 필요하다.

Single crystals, which have complexed composition, are fabricated by solid state grain growth. However, it is hard to achieve stable properties in a single crystal due to trapped pores. Aerosol deposition (AD) is suitable for fabrication of single crystals with stable properties because this process can make a high density coating layer. Because of their unique features (nano sized grains, stress inner site), it is hard to fabricate single crystals, and so studies of grain growth behavior of AD film are essential. In this study, a BaTiO3 coating layer with ~ 9 μm thickness is fabricated using an aerosol deposition method on (100) and (110) cut SrTiO3 single crystal substrates, which are adopted as seeds for grain growth. Each specimen is heat-treated at various conditions (900, 1,100, and 1,300℃ for 5 h). BaTiO3 layer shows different growth behavior and X-ray diffraction depending on cutting direction of SrTiO3 seed. Rectangular pillars at SrTiO3 (100) and laminating thin plates at SrTiO3 (110), respectively, are observed.

In order to analyze the effect of hot asymmetric rolling on the microstructure and texture of aluminum alloy and to investigate the effect of the texture on the formability and plastic anisotropy of aluminum alloy, aluminum 6061 alloy is asymmetrically rolled at room temperature, 200 ℃, 350 ℃, and 500 ℃, and the results are compared with symmetrically rolled results. In the case of asymmetric rolling, the equivalent strain (εeq) is greatest in the upper roll part where the rotational speed of the roll is high and increases with increasing rolling temperature. The increase rate of the mean misorientation angle with increasing temperature is larger than that during symmetrical rolling, and dynamic recrystallization occurs the most when asymmetrical rolling is performed at 500 ℃. In the case of hot symmetric rolling, the {001}<110> rotated cube orientation mainly develops, but in the case of hot asymmetric rolling, the {111}<110> orientation develops along with the {001}<100> cube orientation. The hot asymmetric rolling improves the formability (r) of the aluminum 6061 alloy to 0.9 and reduces the plastic anisotropy (Δr) to near zero due to the {111}<110> shear orientation that develops by asymmetric rolling.

본 실험은 벼 육묘장에 설비된 시설과 장비를 이용하 여 어린잎채소 재배 가능성을 검토하면서 층위에 따른 적합한 품종을 선발하기 위해 수행하였다. 공시 작물은 국화과 3종(‘진빨롤라’, ‘로메인화이트’, 왕고들빼기), 배추과 2종(다채, 적다채) 및 아마란스이며, 고온기에 벼육 묘판(L60×W30×H2cm)에서 재배하였다. 파종된 벼육묘판은 벼 다단재배상(L120×W60×H195cm, 10층)의 저층 (지면으로부터 15cm, 1층), 중간층(지면 115cm, 4층), 고 층(지면 175cm, 7층)에 임의 배치하였다. 관수는 자동 관수시스템을 이용하여 하루 2~3회 스프레이 관수하였고, 생육조사는 어린잎채소 적정 크기에(초장 10cm 이내) 도달하는 시점에 수확하여 생육과 색도를 조사하였다. 재배 기간 동안(2016년 6월 30일~7월 31일) 주간 온도는 27.4~28.1oC로 층위 간 차이가 없었으나, 고층 일사량은 저층, 중간층보다 약 37%, 22% 높았다. 공시 작물의 엽장, 엽폭, 엽수는 중, 고층에서 높은 경향을 보였으나 품종별 생체중은 층위에 따라 차이를 보였다. 누적 광량에 따른 생육 상관성을 분석한 결과 아마란스는 모든 생육 요소가 누적 광량과 높은 상관성을 보인 반면, 나머지 품종들은 생육 요소에 따라 차이를 보였다. 엽생육, 생체중 및 엽색도를 분석한 결과 벼 다단 재배 상의 층위에 따른 어린잎채소의 적정 층위로 고층에서는 아마란스와 적다채, 왕고들빼기와 다채는 중간층과 고층에서, ‘로메인화이트’는 중간층 재배가 적합하였다. ‘진 빨롤라’는 저층에서 엽장과 생체중이 가장 좋았으나, 적 색 발현이 낮아 고층 재배가 적합하였다.

베트남 메콩 델타 지역은 베트남에서도 쌀 생산이 활발히 이루어지는 지역으로 꼽히고 있으나 기후온난화에 따른 고온 현상 증가로 쌀생산량 감소의 우려가 증대되고 있다. 이에 고온에 따른 벼 피해발생 현황 및 대응 기술에 대한 정보를 제공하고자 한다. 베트남의 평균기온은 2060년 까지 약 2.7oC 증가, 35oC 이상의 폭염은 2030년까지 2달 이상 길어질 것으로 예측되고 있으며 기온상승에 따라 기온이 높은 작기의 벼 생산량이 감소되고 있다. 벼 개화기 온도가 33oC 이상으로 높을 시, 화분의 감수분열에 영향을 미쳐 화분의 활력이 저하되며 수술에서 약의 개열이 감소되어 화분의 방출이 감소될 뿐만 아니라 화분이 암술의 주두에 부착하여 발아 시 발아율을 낮추어 불임 발생이 증가하게 된다. 베트남의 벼 연구소는 고온에 대비하여 베트남 벼 생산의 안정화를 위해서 개화기에 내열성을 가지는 품종 육성 뿐만 아니라 이른 아침에 개화할 수 있는 품종을 육성하고 있다. 또한 재배 적인 측면에서 고온 피해를 줄일 수 있도록 벼 재배시기를 조절하여 기존 3기작에서 고온피해가 큰 시기의 재배를 제외한 2기작으로 재배하는 반면 파종 및 이앙시기를 조절하여 벼의 생육량을 충분히 확보하여 2기작에 따른 수량감소를 최소화하는 연구가 필요하다. 더불어 벼를 재배하지 못하는 무더운 계절에는 농업인의 소득보존을 위해 논을 이용한 물고기 양식 기술 도입하는 것도 필요하며, 시비 방법 등의 개선을 통한 벼 생육량 조절, 물관리 기술 개발을 통한 포장 미세기상변화 등의 연구가 필요할 것으로 판단된다.

We analyzed the anthocyanin accumulation, abscisic acid (ABA), gibberellic acid (GA) contents and metabolic genes expression in berry skins under high temperature (High T) at veraison, in order to investigate the cause of bad coloration of 'Kyoho' grape due to High T in summer season. The coloration of ‘Kyoho’ grapes was stopped by High T for 10 days from veraison, and the fruit quality was not affected except skin color. Total anthocyanin of skins was decreased by High T treatment and malvidin and peonidin were decreased compared to control. In berry skins, ABA content did not decrease by High T treatment, but it was rather higher than that of control. GA content was increased about two times compared to the control after 10 days of High T treatment, which caused decreased ratio of ABA/GA. Analysis of expression of anthocyanin biosynthetic genes showed that the early biosynthetic genes were not affected by High T and the expression of UFGT was decreased by temperature treatment. ABA biosynthetic gene expressions were not affected by High T and the expression of GA20ox1 and GA2ox1/2, which are known to regulate the biosynthesis and inactivation of GA, were increased and decreased by High T, respectively. Therefore, the bad coloration of ‘Kyoho’ grapes under the High T at veraison was due to inhibition of anthocyanin biosynthesis of skin, and it was suggested that the anthocyanin biosynthesis was controlled by the ratio of ABA and GA rather than ABA content.

To fabricate the 5182 aluminum-polymer sandwich panels, the strength of 5182 aluminum panels, which are the skin sheets that constitutes the sandwich composite panels, is changed according to the degree of heat treatment after rolling, and the characteristics of sandwich panel are also changed. In addition, in the stress-strain curves of the sandwich panel, the serration behavior observed in the 5182 aluminum alloy sheet is also observed. This serration behavior causes surface roughness during sheet forming, which is a serious problem in application to automotive body sheet. In this study, the tensile properties of the 5182 aluminum sandwich panels at room and elevated temperature were carefully investigated by tensile test. It can be found that when the aluminum surface sheets having insufficient heat treatment time is applied, the serration behavior does not completely disappear from the temperature of the room temperature to 160℃.