PURPOSES : This study provides fundamental information on the temperature variations in tunnel structures during severe fire events. A fire event in a tunnel can drastically increase the internal temperature, which can significantly affect its structural safety. METHODS : Numerical simulations that consider various fire conditions are more efficient than experimental tests. The fire dynamic simulator (FDS) software, based on computational fluid dynamics (CFD) and developed by the National Institute of Standards and Technology, was used for the simulations. The variables included single and multiple accidents involving heavy goods vehicles carrying 27,000 liters of diesel fuel. Additionally, the concrete material characteristics of heat conductivity and specific heat were included in the analysis. The temperatures of concrete were investigated at various locations, surfaces, and inside the concrete at different depths. The obtained temperatures were verified to determine whether they reached the limits provided by the Fire Resistance Design for Road Tunnel (MOLIT 2021). RESULTS : For a fire caused by 27,000 liters of diesel, the fire intensity, expressed as the heat release rate, was approximately 160 MW. The increase in the carrying capacity of the fire source did not significantly affect the fire intensity; however, it affected the duration of the fire. The maximum temperature of concrete surface in the tunnel was approximately 1400 ℃ at some distance away in a longitudinal direction from the location of fire (not directly above). The temperature inside the concrete was successfully analyzed using FDS. The temperature inside the concrete decreased as the conductivity decreased and the specific heat increased. According to the Fire Resistance Design for Road Tunnel (MOLIT 2021), the internal temperatures should be within 380 ℃ and 250 ℃ for concrete and reinforcing steel, respectively. The temperatures were found to be approximately 380 ℃ and 100 ℃ in mist cases at depths of 5 cm and 10 cm, respectively, inside the concrete. CONCLUSIONS : The fire simulation studies indicated that the location of the maximum temperature was not directly above the fire, possibly because of fire-frame movements. During the final stage of the fire, the location of the highest temperature was immediately above the fire. During the fire in a tunnel with 27,000 liters of diesel, the maximum fire intensity was approximately 160 MW. The capacity of the fire source did not significantly affect the fire intensity, but affected the duration. Provided the concrete cover about 6 cm and 10 cm, both concrete and reinforcing steel can meet the required temperature limits of the Fire Resistance Design for Road Tunnel (MOLIT 2021). However, the results from this study are based on a few assumptions. Therefore, further studies should be conducted to include more specific numerical simulations and experimental tests that consider other variables, including tunnel shapes, fire sources, and locations.

전 세계 대부분의 국가들은 탄소배출량을 줄이기 위한 노력을 지속하고 있다. RC구조물의 탄소배출량을 줄이기 위해 수십 년간 건설 분야의 많은 연구자들이 철근콘크리트 구조물에서 철근을 FRP보강근으로 대체하기 위한 연구를 수행하여 왔다. 북미지역을 비롯한 일부 지역에서는 해양구조물이나 도로 등에 CFRP보강근을 사용한 바 있다. 그러나 건축물에는 철근을 CFRP보강근으로 대체한 사례와 적용을 위한 연구는 거의 진행되지 않았다. 따라서 본 연구에서는 예제건물을 선정하여 철근콘 크리트구조로 설계한 후, 철근을 CFRP보강근으로 대체하여 설계함으로써, 철근콘크리트건물에서 철근을 CFRP보강근으로 대체 하였을 때 철근량을 비교하였다. 그 결과 슬래브의 철근비가 0.005미만으로서 CFRP의 사용량을 줄일 수 있을 뿐만 아니라 안전 율 측에서도 우수한 것으로 나타났다.

PURPOSES : The objectives of this study are to evaluate the condition of concrete bridge decks using the multi-channel ground penetrating radar (GPR) testing and compare the value of its dielectric constant value with actual concrete condition. METHODS : The reflection coefficient method was used to measure the dielectric properties of concrete bridge decks. Air-coupled step-frequency GPR testing was used to measure the time taken for reflection from the interfaces between the layers. Specimens of the asphalt mixture and concrete bridge-deck were collected by field coring. GPR testing was conducted on two bridges with different concrete bridge deck conditions on national highways. After the GPR tests, the actual conditions of the concrete bridge deck were investigated using specimen coring. RESULTS : GPR testing indicated that the dielectric constants of concrete bridge decks in good condition ranged from 8 to 10, whereas those corresponding to poor condition ranged from 4 to 6. The results of GPR testing can determine the actual condition and degree of distress of concrete bridge decks determined from the specimen coring data. Therefore, GPR testing is appropriate for nondestructively evaluating the condition of a concrete bridge deck. CONCLUSIONS : The analysis results of the dielectric constants of the concrete bridge deck obtained from multichannel GPR testing were consistent with the actual bridge deck conditions. In the near future, an additional verification process for this approach under different bridge conditions will be required to improve its precision and ensure reliability.

철근콘크리트는 가장 널리 사용되는 건축자재로 최근 노후 시설물이 증가하면서 노후 구조물에 대한 안전성 검토가 매우 중요한 문제로 대두되고 있다. 본 연구에서는 대표적인 열화 인자인 동결융해와 철근부식 그리고 동결융해와 철근부식의 복합적 열화에 따른 RC 휨 부재의 거동을 실험적으로 평가하였다. 4개의 철근콘크리트 휨 부재를 제작하였으며 각 열화 인자에 따른 RC 휨 부재의 거동을 평가하기 위해 4점 재하법을 이용하여 정적실험을 수행하였다. 동결융해는 총 300 사이클의 급속동 결융해실험을 수행하였으며, 부식은 전위차부식촉진실험을 수행하였다. 실험 결과, 동결융해로 인해 콘크리트의 압축강도가 12% 감소하였으며 RC 보 부재의 상부 압축부의 파쇄 범위가 증가하였고 최대강도가 6% 감소하였다. 철근부식으로 인해 RC 휨 부 재의 항복강도가 1.2%, 최대강도가 7% 감소하였으며, 복합열화로 인해 RC 휨 부재의 항복강도가 2.4%, 최대강도가 9% 감소하 였다.