The microstructural evolution and modulation of mechanical properties were investigated for a Ti65Fe35 hypereutectic alloy by addition of Bi53In47 eutectic alloys. The microstructure of these alloys changed with the additional Bi- In elements from a typical dendrite-eutectic composite to a bimodal eutectic structure with primary dendrite phases. In particular, the primary dendrite phase changed from a TiFe intermetallic compound into a β-Ti solid solution despite their higher Fe content. Compressive tests at room temperature demonstrated that the yield strength slightly decreased but the plasticity evidently increased with an increasing Bi-In content, which led to the formation of a bimodal eutectic structure (β-Ti/TiFe + β- Ti/BiIn containing phase). Furthermore, the (Ti65Fe35)95(Bi53In47)5 alloy exhibited optimized mechanical properties with high strength (1319MPa) and reasonable plasticity (14.2%). The results of this study indicate that the transition of the eutectic structure, the type of primary phases and the supersaturation in the β-Ti phase are crucial factors for controlling the mechanical properties of the ultrafine dendrite-eutectic composites.

This present study deals with the effect of micro-alloying elements and transformation temperature on the correlation of microstructure and tensile properties of low-carbon steels with ferrite-pearlite microstructure. Six kinds of lowcarbon steel specimens were fabricated by adding micro-alloying elements of Nb, Ti and V, and by varying isothermal transformation temperature. Ferrite grain size of the specimens containing mirco-alloying elements was smaller than that of the Base specimens because of pinning effect by the precipitates of carbonitrides at austenite grain boundaries. The pearlite interlamellar spacing and cementite thickness decreased with decreasing transformation temperature, while the pearlite volume fraction was hardly affected by micro-alloying elements and transformation temperature. The room-temperature tensile test results showed that the yield strength increased mostly with decreasing ferrite grain size and elongation was slightly improved as the ferrite grain size and pearlite interlamellar spacing decreased. All the specimens exhibited a discontinuous yielding behavior and the yield point elongation of the Nb4 and TiNbV specimens containing micro-alloying elements was larger than that of the Base specimens, presumably due to repetitive pinning and release of dislocation by the fine precipitates of carbonitrides.

In order to reconstruct a benthic foodweb structure and assess the role of benthic microalgaes as a diet source for benthos, we analyzed the carbon and nitrogen stable isotopes of diverse benthos (bivalves, crustaceans, gastropods and fishes) and potential diets (particulate organic matter, sedimentary organic matter, benthic microalgae, seagrass, and macroalgaes) in the intertidal mudflat surrounding Yeongheung Island. The δ13C values of the diets indicated wide ranges (- 26.5‰ to - 8.4‰) while benthos showed a small range of δ13C values (-12.1‰ to - 17.8‰), although they were in the same range. Except for green algaes among the macroalgaes as well as sedimentary organic matter, δ15N values of the diet candidates (5.7±1.0‰) were lighter in comparison to those of the benthos (11.8±1.9‰). Based on the δ13C and δ15N data, the benthos were classified into 3 groups, indicating a different diet and trophic position. But benthic microalgae is the most important diet source for all three benthos groups based on their stable isotope ratios, suggesting benthic microalgae should be a main diet to the intertidal ecosystem. Hence this study highlights that the biomass of benthic microalgae as biological resource should be evaluated for the management of the intertidal ecosystem of Yeongheung Island.

In this study, to confirm the effect of alloying elements on the phase transformation and conditions of the friction stir process, we processed two materials, SS400 and SM45C steels, by a friction stir process (FSP) under various conditions. We analyzed the mechanical properties and microstructure of the friction stir processed zone of SS400 and SM45C steels processed under 400RPM - 100mm/min conditions. We detected no macro (tunnel defect) or micro (void, micro crack) defects in the specimens. The grain refinement in the specimens occurred by dynamic recrystallization and stirring. The microstructure at the friction stir processed zone of the SS400 specimen consisted of an α-phase. On the other hand, the microstructure at the friction stir processed zone of the SM45 specimen consisted of an α-phase, Fe3C and martensite due to a high cooling rate and high carbon content. Furthermore, the hardness and impact absorption energy of the friction stir processed zone were higher than those of base metals. The hardness and impact absorption energy of FSPed SM45C were higher than that of FSPed SS400. Our results confirmed the effect of alloying elements on the phase transformation and mechanical properties of the friction stir processed zone.

AI-Mg-합금의 용융산화에 의해 생성되는 AlO2O3-복합재료의 미세구조에 미치는 합금원소의 영향을 연구하였다. AI-1Mg 합금과 AI-3Mg 합금을 기본으로하여 Si, Zn, Sn, Cu, Ni, Ca, Ce를 1, 3, 5 %를 무게비로 첨가하였다. 각 합금을 1473K에서 20시간 유지하여 산화시킨 후 산화층의 거시적 형상과 미세구조를 광학현미경으로 관찰하였다. 각 미세구조의 상분율을 상분석기로 측정하였다. 산화층의 최첨단면은 SEM과 EDX로 관찰하고 분석하였다. Cu나 Ni를 첨가한 합금으로부터 성장한 산화층의 미세구조가 가장 치밀하였다. Zn이 포함된 합금으로부터 성장한 산화층 최첨단 성장면에는 ZnO가 관찰되었다. Zn이 포함되지 않은 다른 합금의 성장 전면에는 항상 MgAi2O4상이 관찰되었다.

The effects of Mn and Co additions up to 0.6 and 2.0 wt% respectively and the amount of cold-rolled reduction on the thermal expansion coefficient (TEC) of powder rolled Fe-Ni Invar strips were investigated. The compacted strips were sintered, homogenized and cold-rolled to the final thickness of 0.8 mm, 0.65 mm and 0.4 mm. All the strips reached full density except the case of 0.8 mm sample which has a very few porosities. The interstitials which are well known to increase TEC were minimized to the level of 10 rpm C,5 and N,0 by the processing. TEC was found to decrease by increasing the cold reduction. The Mn content had little effect on the TEC. But in Fe-Ni-Co system, TEC decreased with Co content up to 0.4 wt% and then increased, yielding the minimum value of at 0.4 wt% Co. This value is much lower than that of commercial Invar product. Such effect of Co is considered to be related with the maxiumum spontaneous- magnetostriction effect.

과공정 Al-18wt%Si합금의 초정 Si입자의 미세화에 미치는 첨가원소의 영향에 관하여 조사하였다. 초정 Si입자의 크기는 P량이 증가함에 따라 미세해졌으며 적정 P량은 40ppm이었다. 최적주입온도는 AlCuP, CuP 경우 각각 750˚C, 800˚C이었으며 미세화 처리 후 10분 이상 경과되어도 초정 Si입자의 크기는 변화가 없었다. 또한 WDS분석 결과 초정 Si내에 AIP가 핵생성 site로 존재함을 알 수 있었다.

From November 2013 to December 2016, ambient fine particulate matter (PM2.5) was sampled in the downtown area of Jeju City, South Korea, which has seen rapid urbanization. The atmospheric concentrations of elements were measured in the PM2.5 samples. This study focused on Cd, Cr, Cu, Mn, Ni, Pb, As, Sb, Sn, V, and Zn. The concentrations of Al, Na, K, Fe, Ca, Mg, Sr, and La were also obtained for reference. The objectives of this study were to examine the contributions of these elements to PM2.5 concentrations in downtown Jeju City, and to investigate the inter-element relationships and the elemental sources by using enrichment factors and principal components analysis (PCA). A composition analysis showed that the 19 elements constituted 6.65 % of the PM2.5 mass, and Na, K, Al, Fe, Ca, Mg, and Zn constituted 98 % of the total ion mass. Seasonal trend analysis for the sampling period indicated that the concentrations of the elements increased from November to April. However, no substantial seasonal variations were found in the concentrations of the elements. The composition ratios of some elements (Cu/Zn, Cu/Cd, Cu/Pb, V/Ni, and V/La) were found to be out of range when compared to the literature from other urban areas. The ratios between the elements and the PCA results showed that local contaminant sources in Jeju City rarely influence the composition of PM2.5. This suggests that the major sources of PM2.5 in Jeju City may include long-range transport of fine particulate matter produced in other areas.

금강초롱꽃과 근연분류군 4속 9분류군에 대한 표피 및 화분의 미세구조, 동위효소 분석을 통하여 금강초롱꽃속(屬)이 특산속으로서 구분이 가능한가를 알아보았다. 표피는 미세구조에서는 잎이 표면과 이면세포의 모양, 화피의 세포형태, 종피의 미세구조 등이 속과 종을 구분하는데 유용한 형질로 나타났으며, 화분학적 형질에서는 표면무늬와 전체 형태에 많은 변이가 있어 속내 분류군들의 유집 및 분류가 불가능하였다. 동위효소 분석에서는 분류군에 따라 지역, 집단간 변이가 매우 심하게 나타났지만 금강초롱꽃과 가장 유사한 분류군은 초롱꽃과 섬초롱꽃으로 유집되어 나타났다. 이상의 결과에서 금강초롱꽃속(屬)은 근연 분류군과 표피의 형질, 동위효소 분석등에서 근연 분류군과 뚜렷한 차이가 있어 특산속으로서 잘 구분되었다.