검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 51

        3.
        2023.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, when Butyl ether, a type of diether-based oxygenated fuel, is mixed in each volume ratio in a naturally aspirated direct injection diesel engine, the exhaust gas emission characteristics of the oxygenated component in the fuel affect each operating area of the engine I wanted to investigate the effect on. For comparative measurement of engine performance and exhaust emissions, commercial diesel and butyl ether mixed fuels were classified into 4 types according to the mixing ratio and tested. As the content of butyl ether in fuel increases, soot emission reduction increases, and when the maximum mixing amount of butyl ether (diesel 80vol-% + BE 20vol%) is applied, compared to the case of using only diesel as fuel, at 2500 rpm and no load, 39%, and about 32% of smoke reduction effect at full load was confirmed.
        4,000원
        5.
        2022.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Dimethoxymethane, also known as methylal, is an oxygenated additive that contains approximately 42% oxygen content and is soluble in diesel fuel. Experiments were conducted by using the five kinds of blended fuels with different volumetric percentage of DMM in a diesel fuel. The test engine was used four stroke, single cylinder, DI diesel engine. Also, data was collected at 24 kinds of various engine speed-load conditions. The aim of this study was to examine the effects of the addition of oxygenated additive to diesel fuel on the emissions and the performance. Smoke emissions of all DMM blended fuels were reduced substantially in comparison with diesel fuel. In addition, this study showed that simultaneous reduction of NOx and smoke emissions could be achieved by oxygenated additive and EGR method that was applied to decrease smoke emissions increasing with NOx emissions reduction.
        4,000원
        6.
        2022.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Diesel engine has the advantages of strong power, low fuel consumption and good durability, so it has been widely used in transportation, automobile, ship and other fields. However, the nitrogen oxides(NOx) and particulate matter(PM) emitted by diesel engines have become one of the main causes of air pollution. Especially during idling, the engine temperature is low, and there are more residual exhaust gases in the combustion chamber, resulting in the formation of more harmful emissions. In this study, performance of a single cylinder, four-stroke, direct injection (DI) diesel engine fueled with diesel–biodiesel mixtures has been experimentally investigated.
        4,000원
        8.
        2021.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the effects of fuel injection pressure changed from 45 to 65 MPa on combustion and emission characteristics were investigated in a common rail direct injection (CRDI) diesel engine fueled with diesel and palm oil biodiesel blends. The engine speed and engine load were controlled at constant 1700rpm and 100Nm, respectively. The tested fuel were PBD20 (20 vol.% palm oil biodiesel blended with 80 vol.% diesel fuel). The main and pilot injection timing was fixed at 3.5°CA BTDC and 27°CA BTDC (before top dead center), respectively. The experimental results show that the combustion pressure and heat release rate increased. In addition, the indicated mean effective pressure (IMEP) and maximum combustion pressure increased with an increase of the fuel injection pressure. Hydrocarbon (HC), smoke opacity and carbon monoxide (CO) decreased, but oxides of nitrogen (NOx) emissions increased as fuel injection pressure increased.
        4,000원
        9.
        2021.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, blending oils of diesel oil and butanol were used as fuel oil for diesel engine to measure combustion pressure, fuel consumption, air ratio and exhaust gas emission due to various operating conditions such as engine revolution and torque. Using these data, the results of analyzing the engine performance, combustion characteristics and exhaust emission characteristics such as NOx (nitrogen oxides), CO2 (carbon dioxide), CO (carbon monoxide) and soot were as follows. The fuel conversion efficiency at each load was highest when driven in the engine revolution determined by a fixed pitch propeller law. Except 30% butanol blending oil, fuel conversion efficiency of the other fuel oils increased as the load increased. Compared to diesel oil, using 10% and 20% butanol blending oil as fuel oil was advantageous in terms of thermal efficiency, but it did not have a significant impact on the reduction of exhaust gas emissions. On the other hand, future research is needed on the results of the 20% butanol blending oil showing lower or similar levels of smoke concentration and carbon monoxide emission rate other than those types of diesel oil.
        4,000원
        10.
        2020.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        High-performance vehicles with V6 or higher are designed with a dual exhaust system to satisfy both performance and quietness at the same time, and have a confluence geometry for the purpose of stably maintaining the back pressure inside the pipe. The exhaust system generates noise and vibration under the influence of the rotating engine. In particular, in a state such as idling, vibration occurs in a certain frequency range, which may affect the natural vibration of the exhaust system. Therefore, in this study, the optimal shape is proposed by comparing the ignition frequency calculated based on the vibration measurement result in the idle state and the numerical analysis result.
        4,000원
        13.
        2020.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, we investigated the effects of diesel-palm oil biodiesel-ethanol blends on combustion and emission characteristics in a 4-cylinder common rail direct injection (CRDI) diesel engine at low idling operations. The engine speed and engine load was 750 rpm and 40 Nm, while the main and pilot injection timing was respectively fixed at 2 °CA before top dead center (BTDC) and 20 °CA BTDC. The experimental results showed that the cylinder pressure increased with the increasing of palm oil biodiesel ratio from 20% to 100%. In addition, the peak value of cylinder pressure increased by 4.35% compared with pure diesel fuel when 5 vol.% ethanol oil added to diesel oil. Because the palm oil biodiesel and ethanol are the oxygenated fuel, the oxygen content played an important role in improving combustion. Based on the high oxygen content of biodiesel and ethanol, their mixing with diesel fuel effectively reduced PM emissions but increased NOx slightly, while CO and HC had no significant changes.
        4,000원
        14.
        2020.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the effect of various pilot injection timings on combustion and emission characteristics were investigated in a common-rail direct injection (CRDI) diesle engine fueled with diesel-ethanol blends. The engine speed and engine load were controlled at constant 1500rpm and 70Nm, respectively. The tested fuels were DE0 (pure diesel fuel), DE5 (5 vol.% ethanol blended with 95 vol.% diesel oil), DE10 (10 vol.% ethanol blended with 90 vol.% diesel oil) and DE15 (15 vol.% ethanol blended with 85 vol.% diesel oil). The main injection timing was fixed at 0°CA TDC (top dead center), while various pilot injection timings including 25°CA BTDC (before top dead center), 20°CA BTDC and 10°CA BTDC were selected as the experimental variable. The experimental results showed that various pilot injection timings had little effect on the peak value of cylinder pressure, but had great influence on the start of combustion. The peak value of heat release rate (HHR) increased with the increase of ethanol content. However, the peak value of HRR reduced as the pilot injection is delayed. The diesel fuel containing 10% ethanol had a highest peak value of combustion pressure compared with the others, while the pilot injection timing occurred at 25°CA BTDC. On the other hand, the exhaust emissions of DE10 was also the lowest compared with the others. In addition, with the increase of ethanol content in diesel the PM and NOx emissions reduced.
        4,000원
        17.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        최근 지구의 기후변화는 온실가스가 원인으로 전 세계적 대기환경문제로 크게 부각되고 있다. 국내에서도 기후변화에 적극 대응하기 위한 기술개발이 꾸준히 진행되고 있다. 날씨의 이상고온으로 인한 환경에 미치는 영향과 갑작스런 집중호우가 환경에 미치는 영향을 대상으로 하였다. 우리생활 주변 대기온도가 상승하였을 때 온도변화에 의한 대기오염발생에 미치는 영향을 연구하고자 한다. 본 연구의 실험조건은 선박 디젤기관에서 회전수 1400 rpm, 1600 rpm 그리고 1800 rpm, 부하는 0 %에서 25 %씩 100 %까지 하였고, 흡기 온도변화 는 20℃에서 50℃까지 구분하여 연구하였다. 연구한 결과 흡기온도가 증가함에 따라 일산화탄소 및 탄화수소는 약간 감소하였으나 연료 소비율, 질소산화물, PM은 약간 증가하였다. 또한 연소온도는 큰 변화가 없었다.
        4,000원
        19.
        2019.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The purposes of improving air pollution and suggesting energy resources have intensified research on various alternative energy for diesel combustion engines to solve severe environmental influences caused by air pollution. In this study, the applicable possibility of biodiesel and oxygenates (EGBE) was investigated as a cuspy method on decreasing the smoke emission. The smoke emission of blending fuel (biodiesel and EGBE) was reduced in comparison with commercial diesel fuel and it was reduced almost 63% at 2000 rpm, full load. But torque and brake specific energy fuel consumption rate didn't have any large changes. Also, the effectiveness of exhaust gas recirculation (EGR) for the reduction of NOx emission has been investigated. It was shown that simultaneous reduction of NOx and smoke emission was achieved with biodiesel(90%), oxygenates (10%) and cooled EGR rates (10%) in an IDI diesel engine.
        4,000원
        20.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, effects of reducing white smoke at a heat exchange system for white smoke reduction were studied in the winter season. For this purpose, the heat transfer processes on the exhaust air were investigated by Solidworks. Five wave heat exchangers of air-to-air and air-to-water type were applied for the exhaust air heat recovery. The analytical condition of the exhaust air was fixed and the computational analysis was performed according to the change of SA(supply air) inlet velocities. In order to evaluate the performance of the heat exchange system for white smoke reduction, W(water)/SA recovered capacities and the temperature/ absolute humidity reduction rate were calculated. As SA inlet velocity increased, the exit temperature and absolute humidity of the mixing zone were reduced by up to about 40℃ and 0.12kg/kg respectively. Also, W/SA recovered capacities increased linearly up to about 35%.
        4,000원
        1 2 3