In the development of eco-friendly vehicles such as electric vehicles, weight reduction has become a very important design target. Seat weight reduction is very important in vehicle weight reduction. In this study, the energy absorption characteristics of Almag material, an alloy of aluminum and magnesium, and mild steel SAFH440, SAFH590, SAFC780, and SAFH980 were analyzed to obtain a true stress versus true strain curve that was correlated with the test. By performing the seat frame structure analysis using the obtained analysis material property, it was possible to compare the deformation between lightweight material, Almag and mild steel materials. In addition, it was confirmed that the weight reduction effect was 25.8% when applying Almag, an equivalent lightweight material that gives the same maximum deformation as SAFH980, a high-strength mild steel.

Steel plate shear walls (SPSWs) have been recognized as an effective seismic-force resisting systems due to their excellent strength and stiffness characteristics. The infill steel plate in a SPSW is constrained by a boundary frame consisting of vertical and horizontal structural members. The main purpose of this study was to investigate deformation modes and hysteretic characteristics of steel plate shear walls (SPSWs) to consider the effects of their aspect ratios and width-to-thicness ratios. The finite element model (FEM) was establish in order to simulate cyclic responses of SPSWs which have the two-side clamped boundary condition and made of conventional steel grade. The stress distribution obtained from the FEA results demonstrated that the principal stresses on steel plate with large thickness-to-width ratio were more uniformly distributed along its horizontal cross section due to the formation of multiple struts.

The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray,  becomes a sin function. Since  cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.

In this study, controlling pattern gap was induced by deformation of the stretchable substrate. The pre-fabricated pattern was made by depositing an Au(gold) on the Si substrate, and PDMS(Polydimethylsiloxane) was used for the stretchable substrate in consideration of surface energy, formability, and viscoelastic characteristics. For uniform deformation of PDMS, it is manufactured in the form of a tensile specimen using a molding method. An external force is applied to the deformable substrate in the uni-axial direction using a self-manufactured JIG, and the Au thin film pattern is transferred to the substrate under tensile state. After that, the external force is removed, and the PDMS specimen is recovered to its initial state. At this time, it can be seen that the pre-fabricated pattern gap is shortened from the initial size due to the viscoelastic properties of the PDMS. As a result, it was characterized to deformation rate of the pattern gap according to elongation rate of PDMS.

(Bi1/2Na1/2)TiO3 (BNT)-based ceramics are considered promising candidates for actuator application owing to their excellent electromechanical strain properties However, to obtain large strain properties, there remain several issues such as thermal stability and high operating fields. Therefore, this study investigates a reduction of operating field in (0.98-x)Bi1/2Na1/ 2TiO3-0.02 BiAlO3-xSrTiO3 (BNT-2BA-100xST, x = 0.20, 0.21, 0.22, 0.23, and 0.24) via analyses of the microstructure, crystal structure, dielectric, polarization, ferroelectric and electromechanical strain properties. The average grain size of BNT-2BA- 100xST ceramics decreases with increasing ST content. Results of polarization and electromechanical strain properties indicate that a ferroelectric to relaxor state transition is induced by ST modification. As a consequence, a large electromechanical strain of 592 pm/V is obtained at a relatively low electric field of 4 kV/mm in 22 mol% ST-modified BNT-2BA ceramics. We believe that the materials synthesized in this study are promising candidates for actuator applications.

This study deals with the yielding behavior and strain aging properties of three bake hardening steels with dualphase microstructure, fabricated by varying the annealing temperature. Bake hardening and aging tests are performed to examine the correlation of martensite volume fraction with yielding behavior and strain aging properties of the bake hardening steels with dual-phase microstructure. The volume fraction of martensite increases with increasing annealing temperature. Roomtemperature tensile test results show that the yielding behavior changes from discontinuous-type to continuous-type with increasing volume fraction of martensite due to higher mobile dislocation density. According to the bake hardening and aging tests, the specimen with the highest fraction of martensite exhibited high bake hardening with low aging index because solute carbon atoms in ferrite and martensite effectively diffuse to dislocations during the bake hardening test, while in the aging test they diffuse at only ferrite due to lower aging temperature.

본 연구에서는 우라늄 폐촉매 처리 공정에서 발생하는 우라늄 함유 폐기물 대상으로 유리-세라믹 매질 구조의 대형 디스크 소결체 형태로 제작 시, 최종 제작된 소결체의 비등방향 수축 특성 및 변형율 변화를 연구하였다. 본 연구에서는 최대 직경 40 cm를 갖는 다양한 크기 원형 디스크 형태와 원형 디스크의 1/4 크기의 부채꼴 형 소결체를 제작하여 이들의 비등방성 수축 특성을 평가하였다. 60 MPa 압력하에서 만들어지는 성형체는 소결 시 성형체의 크기 및 형태에 관계없이 높은 등방성 수축하였다. 제조된 전체 소결체에 대한 비등방성율은 평균 1.6%이었고 이때 평균 부피 감용율은 37.4% 이었다. 이러한 결과 로부터 국내에서 발생한 우라늄 폐촉매를 처리하기 위한 공정에서 발생하는 우라늄 함유 폐기물은 대형 디스크 형태의 유리-세라믹 매질 형태로 고형화함으로써 높은 안정성과 부피감용 효과를 가지며 200 L 드럼에 포장될 수 있음이 확인되었다.

In this study, the flat glass and adsorption pad were modeled using SolidWorks Simulation, to understand the deformation characteristics of the vertical flat glass by the adsorption pressure during vertical transport of LCD. The horizontal and vertical displacements and equivalent stresses of the flat glass were investigated by the structural analysis. From the displacement and stress visualization according to the adsorption pressure, the higher the adsorption pressure, the larger the glass surface protruded. The horizontal deformation of flat glass increased with increasing thickness and the vertical deformation increased with decreasing thickness. In addition, the maximum equivalent stress applied to the flat glass increased significantly as the adsorption pressure increased and the thickness decreased. As a result of the structural analysis, the thinner the thickness of the plate glass, the greater the effect on the adsorption pressure. Especially, the effect of the adsorption pressure was clearly observed at the thickness of 0.5mm.

This study deals with the effect of microstructure factors on the strain aging properties of API X70 pipeline steels with different microstructure fractions and grain sizes. The grain size and microstructure fraction of the API pipeline steels are analyzed by optical and scanning electron microscopy and electron backscatter diffraction analysis. Tensile tests before and after 1% pre-strain and thermal aging treatment are conducted to simulate pipe forming and coating processes. All the steels are composed mostly of polygonal ferrite, acicular ferrite, granular bainite, and bainitic ferrite. After 1% pre-strain and thermal aging treatment, the tensile test results reveal that yield strength, tensile strength and yield ratio increase, while uniform elongation decreases with an increasing thermal aging temperature. The increment of yield and tensile strengths are affected by the fraction of bainitic ferrite with high dislocation density because the mobility of dislocations is inhibited by interaction between interstitial atoms and dislocations in bainitic ferrite. On the other hand, the variation of yield ratio and uniform elongation is the smallest in the steel with the largest grain size because of the decrease in the grain boundary area for dislocation pile-ups and the presence of many dislocations inside large grains after 1% pre-strain.

In this study, PAT protein of genetically modified maize was prepared from the recombinant E. coli strain BL21 (DE3), and mice were immunized with the recombinant PAT protein. After cell fusion and cloning, two hybridoma cells (PATmAb-7 and PATmAb-12) were chosen since the monoclonal antibodies (Mabs) produced by them were confirmed to be specific to PAT protein in the indirect enzyme-linked immunsorbent assay (ELISA) and western blot tests. There were no cross-reactions of either Mabs to other GM proteins or to the extracts of non-GM maize. The ELISA based on the PATmAb-7 can sensitively detect 0.3 ng/g PAT protein in corn. These results indicate that the developed Mabs can be used as bio-receptors in the development of immunosensors and biosensors for the rapid and simple detection of GM corn adulterated in foods.

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at −196 oC due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at −196 oC showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

The effect of strain aging on the tensile properties of API X70 linepipe steel was investigated in this study. The API X70 linepipe steel was fabricated by controlled rolling and accelerated cooling processes, and the microstructure was analyzed using optical and scanning electron microscopes and electron backscatter diffraction. Strain aging tests consisting of 1% pre-strain and thermal aging at 200 oC and 250 oC were conducted to simulate U-forming, O-forming, Expansion(UOE) pipe forming and anti-corrosion coating processes. The API X70 linepipe steel was composed of polygonal ferrite, acicular ferrite, granular bainite, and bainitic ferrite whose volume fraction was dependent on the chemical composition and process conditions. As the thermal aging temperature increased, the steel specimens showed more clearly discontinuous type yielding behavior in the tensile stress-strain curve due to the formation of a Cottrell atmosphere. After pre-strain and thermal aging, the yield and tensile strengths increased and the yield-to-tensile strength ratio decreased because yielding and aging behaviors significantly affected work hardening. On the other hand, uniform and total elongations decreased after pre-strain and thermal aging since dislocation gliding was restricted by increased dislocation density after a 1% pre-strain.

본 연구는 도로함몰과 관련된 연구 중 위험도 등급에 따른 소성변형 특성을 파악하기 위해 수행되었다. 도로함몰 위험도 등급 A, B에 해당하는 지표면으로부터 60cm, 90cm 하부에 모의 동공(얼음)을 설치하였으며, 동공의 크기는 그림 1과 같이 너비와 높이는 50cm, 길이는 100cm, 200cm로 각각 설계하였다. 또한, 배수층을 20cm 설치하여 배수가 가능하도록 설계하였다. 포장가속시험은 4ton의 축하중으로 10km/h의 속도로 운영하였으며, 1,000회, 2,000회, 6,000회, 10,000회 운행 시 마다 소성변형량 변화를 측정하였다. 그 결과 동공의 크기보다는 동공의 깊이가 소성변형에 영향을 크게 미치는 것으로 파악되었다. 그림 1의 1,3번 동공은 폭과 높이는 유사하지만 길이가 각각 1m, 2m로 위험도 등급에서 B, A이다. 하지만, 소성변형량을 비교했을 때 각 횟수마다 비슷한 경향을 보이며 증가하는 추세를 볼 수 있었다. 또한, 2번 동공의 경우 포장층에 가깝게 동공이 형성되어 1,3번 동공과 달리 소성변형량 증가 추세가 다른 동공들에 비해 월등히 빨랐으며, 6,000회 이상 포장가속시험을 수행하기 어려울 정도로 소성변형이 심하게 나타났다. 포장가속시험 수행 결과 동공 생성 초기에 소성변형량 변화폭이 가장 크며, 동공 길이보다는 심도에 포장층이 영향을 크게 받는 것으로 나타났다.

PURPOSES: This study is primarily focused on evaluating the effects of the non-linear stress-strain behavior of RAP concrete on structural response characteristics as is applicable to concrete pavement. METHODS : A 3D FE model was developed by incorporating the actual stress-strain behavior of RAP concrete obtained via flexural strength testing as a material property model to evaluate the effects of the non-linear stress-strain behavior to failure on the maximum stresses in the concrete slab and potential performance prediction results. In addition, a typical linear elastic model was employed to analyze the structural responses for comparison purposes. The analytical results from the FE model incorporating the actual stress-strain behavior of RAP concrete were compared to the corresponding results from the linear elastic FE model. RESULTS : The results indicate that the linear elastic model tends to yield higher predicted maximum stresses in the concrete as compared to those obtained via the actual stress-strain model. Consequently, these higher predicted stresses lead to a difference in potential performance of the concrete pavement containing RAP. CONCLUSIONS : Analysis of the concrete pavement containing RAP demonstrated that an appropriate analytical model using the actual stress-strain characteristics should be employed to calculate the structural responses of RAP concrete pavement instead of simply assuming the concrete to be a linear elastic material.

Magnetostrictive actuator is fabricated with powder nano bonding method instead of sputtering method. Fabrication process and experimental measurement method for magneto-mechanical characteristics is proposed. For the design of highly flexible magnetostrictive actuator, TbDyFe nano powder bonding with Teflon substrate is adopted. The fabrication process for Teflon substrate and nano powder bonding is suggested and magnetostrictive behaviors are investigated. Variable magnetic field is applied to measure the magnetostrictive characteristics and magnetostriction is measured with different waves and different magnitude of magnetic field.

In the present study, the tensile properties and dynamic strain aging of an Fe-24.5Mn-4Cr-0.45C alloy were investigated in terms of strain rate. During tensile testing at room temperature, all the stress-strain curves exhibited serrated plastic flows related to dynamic strain aging, regardless of the strain rate. Serration appeared right after yield stress at lower strain rates, while it was hardly observed at high strain rates. On the other hand, strain-rate sensitivity, indicating a general relationship between flow stress and strain rate at constant strain and temperature, changed from positive to negative as the strain increased. The negative strain-rate sensitivity can be explained by the Portevin Le Chatelier effect, which is associated with dynamic strain aging and is dependent on the strain rate because it is very likely that the dynamic strain aging phenomenon in high-manganese steels is involved in the interaction between moving dislocations and point-defect complexes.

Background: It is necessary to find and develop the effective way of intervention for patients with neck pain, since the neck pain is becoming increasingly common throughout the world. To identify the altered motor control in patient with neck pain would be informative to find and develop the effective way of intervention. Objects: The aim of this study was to review literature regarding the altered motor control in patients with neck pain, measured by using surface electromyography (sEMG), ultrasonography, and functional magnetic resonance imaging (fMRI), and to suggest prospective research work on neck pain. Methods: Case-control (neck pain/healthy) studies published between 2004 and 2015 that investigated neck muscle activation, thickness, cross-sectional area, and fat infiltrate were searched in Scopus, PubMed, and ScienceDirect. Twenty-eight articles were included in this study. Results: sEMG, ultrasonography, and fMRI were used complementarily to investigate the altered superficial and deep neck muscle activation, thickness, cross-sectional area, and fat infiltrate in patients with neck pain. They showed the following altered motor control when compared retrospectively with healthy subjects or during specific functional tasks: (1) increased superficial muscle activation, (2) lesser deep muscle thickness, (3) smaller cross-sectional area of the deep muscle, and (4) greater fat infiltrate in deep muscles. In particular, among the women, the office workers showed higher muscle activation of superficial neck muscles during functional tasks, although they did not have neck pain, than those who were not office workers. Conclusion: Studies revealed that patients with neck pain showed an altered motor control when compared with healthy subjects by using various assessment modalities. Understanding this phenomenon would help researchers design an effective intervention for alleviating neck pain or to evaluate the effectiveness of the intervention. In addition, we recommend that female office workers take measures to care for their necks before developing neck pain.

In this study, analysis on the stiffness of the headrest, the stiffness of front-rear load and the torsion of cushion frame was performed using finite element method in order to investigate the properties of the stress-deformation by material characteristics according to the test requirements of FMVSS (Federal Motor Vehicle Safety Standard). The results are shown that AZ31 (Mg alloy) and A365 (Al alloy) with low modulus of elasticity and density have higher strain rate than steel in terms of stress-deformation and meet the standards for safety within 108 mm of the maximum amount of deformation. Considering it’s safety and durability, however, the selection of AZ31 for light weight seems difficult to gain the reliability because it causes an excessive deformation, and therefore it is not expected to be used for recliner where stress is concentrated and also the bracket linking rail and cushion frame.

This study shows the role of waves, tide, storm surge and river discharge which impact on water level variation in Suyeong bay. Suyeong bay has a narrow inlet channel where is flood dominance caused by rainfall. The effect of typhoons which make a serious