The method of evaluating the forming limit of sheet metal is using the forming limit diagram(FLD), and the test method for measuring forming limit curve(FLC) is ISO standardized. On the other hand, in the case of metal bulk materials, it was confirmed that the forming limit was defined by using various predictive models based on the ductile fracture theory. However it did not show a constant forming limit (limit damage value) depending on the shape of the specimen. Therefore, a study was conducted on the derivation of the triaxial stress curve to predict the fracture of the material for various stress triaxiality, not the existing limit damage value.

Until recently, almost all ETFE film structures that have been erected is the cushion type because there are problems at lower allowable strength under elastic range and viscosity behaviour such as creep and relaxation of ETFE films under long-term stresses. But the number of tension type structures is currently increasing. This paper proposes the stretch fabrication of ETFE film to verify the applicability of ETFE films to tensile membrane structures. First of all, to investigate the possibility of application on tensile membrane structures, the stretch fabrication test is carried out, and it is verified that it is possible to increase the yield strength of the film membrane structures. After simulating the experiment also carries out an analytical investigation, and the effectiveness of the elasto-plastic analysis considering the viscous behavior of the film is investigated. Finally, post-aging tension measurement is conducted at the experimental facilities, and the viscosity behavior resulting from relaxation is investigated with respect to tensile membrane structures.

This paper is presented an experimental studies on bond stress between steel and concrete in concrete filled Rectangular steel tubes. In the actual building frames, vertical dead and live loads on beams are usually transferred to columns by beam-to-column connections. In case when concrete filled steel tubes are used as columns of an actual building frame which has a simple connection, shear forces in the beam ends are not directly transferred to the concrete core but directly to the steel tube. Provided that the bond effect between steel tube and concrete core should not be expected, none of the end shear in the beams would be transferred to the concrete core but only to the steel tube. Therefore, it is important to investigate the bond strength between steel tube and concrete core in the absence of shear connectors.

잔류응력을 측정하는 비파괴 방법중 Neutron diffraction technique의 발달로 인하여 기존의 X-ray diffraction technique에 비하여 잔류응력 측정가능 두께가 대부분의 물질에 있어서 훨씬 깊어졌다. 비파괴 방법으로 부품내의 잔류응력 분포가 측정되어진 경우, 부품의 가공시 잔류응력의 재분포로 인한 형상의 변화를 정량적으로 예측할 수 있는 방법에 대해 어떠한 경우도 논의된 바 없다. 본 연구에서는 축 방향의 잔류응력이 내재하는 strip의 층 가공시 일어나는 strip의 곡율변화를 정량적으로 예측할 수 있는 수식을 제시하였다. 간단히 컴퓨터 프로그램화 할 수 있는 수식을 전개하므로 써 현장에서 유용하게 이용할 수 있게 하였다.

This research presents a uniaxial static stress estimation method for concrete structures by using digital image correlation (DIC) and finite element method. DIC is employed to measure the displacement field, which is induced by drilling a small hole on the concrete surface. The initial static stress level can be estimated by comparing the measured displacement field to that from the corresponding finite element model. A series of experiments in the laboratory environment is conducted to validate the proposed method.

Effect of confining pressure on the shear strength of ultra-high-performance fiber-reinforced concrete (UHPFRCs) was investigated using a new shear test setup. Different confining pressures were applied and maintained to the specimens prior to shear testing. The shear strength of UHPFRCs was obviously sensitive to the confining pressure: the higher confining pressure produced higher shear strength. The confined shear strength could be expressed as a function of unconfined shear strength, confining pressure, and tensile strength.

In this study, axial-stress distribution of enlarged concrete column according to degree of composite is analysed. The analysis showed that axial-stress on existing concrete and new concrete was concentrated to edge in case of lower degree of composite. On the other hand, axial-stress was evenly distributed in case of higher degree of composite.

The hollowed precast concrete (PC) column supports beams during construction so that local compression acts on the column. At that time, the stress distribution from the beams to the column varies if hollow size varies. After the hollow is filled with grout concrete, the column has two layer, outer and inner elements with different compressive strength each other. Therefore, hollow size affect axial capacity of column after filling the hollow. Based on the above background, this paper performed a finite element (FE) analysis with parameter of hollow size to find the stress distribution of hollowed PC column during construction as well as after construction. As an analysis result, the wider the hollow size is, the less local compress strength is during construction. Also, the axial compressive resistance of column decreased when the hollow size is wider.