In this study, the performance evaluation of the RC frame specimen (RV2) which was strengthened by a steel frame and a steel damper with the lateral deformation prevention details proceeded. The comparison objects are bare frame specimen (BF), RV2 and AWD, where AWD is a specimen reinforced with steel damper and aramid fiber sheets. In the evaluation of envelope curve, stiffness degradation, and energy dissipation capacity, RV2 was evaluated to have excellent capacity as a whole. To evaluate the strengthening effect of the steel frame based on the maximum strength and energy dissipation capacity, it was evaluated to have a 38% of the RV2’s capacity.

In this paper, seismic performance evaluation was carried out for eight circular reinforced concrete columns designed seismically by KRTA[1]and KCI[8]. Primary design parameters for such columns included many longitudinal reinforcements, yield strength of reinforcements, the vertical spacing of spirals, aspect ratio, and axial force ratio. The test results showed that all the columns exhibited stable hysteretic and inelastic responses. Based on the test results, drift ratios corresponding to each damage state, such as initial yielding, initial cover spalling, initial core concrete crushing, buckling, and fracture of longitudinal reinforcement and final spalled region, were evaluated. Then, those ratios were compared with widely accepted damage limit states. The comparison revealed that the existing damage states were considerably conservative. This implies that additional research is required for the damage limit states of such columns designed seismically by current Korean design codes.

강진은 적절한 내진 설계 기술이 적용되지 않으면 건물 붕괴로 인하여 극심한 피해가 발생할 수 있다. 이를 해결할 수 있는 면진 기술은 구조물과 지반 사이에 베어링 장치를 적용하여 지진 에너지를 흡수하고 건물에 전달되는 진동을 감쇠한 다. 본 연구는 고무 마찰 베어링 장치의 구조물 적용성을 검증하고 지진으로부터 안전성을 확보하기 위하여 고무 마찰 베어링 프레임 구조물에 대한 수치해석을 수행하였다. 수치해석 결과로써 최대 지붕 가속도와 총 밑면 전단력이 감소되어 내진 성능을 확인하였다. 또한, 최대 층간 변위 및 최대 잔류 층간 변위에 대한 분석 결과로 프레임 구조물을 경제적 복구 수준의 결과를 도 출하여 고무 마찰 베어링 장치의 우수한 내진 성능을 확인하였다.

Sensory evaluation of shucking pressure, pressure holding time, seeding method, difference in full shucking rate in the aquaculture area and shucking oyster was performed using an ultra-high pressure oyster shucking machine. The reaching time for each target pressure is 2.2-2.4 MPa/sec in the range of 180 MPa to 240 MPa. had a rate of pressure rise. There was a difference of 0.5-1.7℃ in the range of 24-27℃ in the seawater temperature before and after the pressure treatment inside the pressure vessel, but there was no specific increase or decrease in seawater temperature. When only the shucking pressure is increased without the pressure holding time, the critical shucking pressure at which the oyster shell is opened and the flesh is peeled in the range of 200 to 220 MPa. When the critical shucking pressure is reached, the oyster sample in the closed vessel is expected to be shucked by about 40%. If there is no pressure holding time when judged only by full shucking, an increase in pressure of about 1.5 MPa is required to further shuck 3% of the oyster population. The oyster samples cultivated in the south coast of Korea were subject to full shucking under the conditions of 220 MPa shucking pressure and two minutes (120 seconds) of pressure holding time, and the difference in the pressure of the oysters according to the oyster seeding method and the farming area was minute. Finally, the condition of 220 MPa of shucking pressure and three minutes of pressure holding time was the best at 1.52 when the result of the sensory evaluation performed manually was set to 1.0. Next was 1.4 under the conditions of 220 MPa of shucking pressure and one minute of pressure holding time (60 seconds), and 1.3 under the condition of 220 MPa and two minutes of pressure holding time (120 seconds). Therefore, it is considered that the most desirable shucking conditions, considering the efficiency and sensory evaluation results, are the conditions of 220 MPa shucking pressure and two to three minutes of pressure holding time.

In the anchovy boat seine fishing boat, it is necessary to select other aquatic organisms other than live anchovies, which are the target species of catch. By making a rotating roller sorter using hydraulic pressure, the anchovy sorting amount was compared and the sorting accuracy of the rotary roller sorter, and the discharge speed of butter fish and jerry fish according to the number of roller revolutions were analyzed. The rotating roller sorter increases the weight of the sorted raw anchovy by 54%, 74% and 91.5% compared to the round bar fixed type, so it can reduce the required time by an average of 73.2%. As a result of converting the sorting accuracy to the weight of pure anchovies excluding the catch weight, the round bar fixed type was 89%; however, the average of the rotating roller sorter was 97.7%. Thus, the sorting accuracy of the rotary roller sorter was further improved by about 8.7%. The roller speed moved 7% at 300 rpm, 7.5% at 600 rpm, and 16% at 900 rpm, so butter fish were discharged overboard 10% faster than jelly fish on average. In addition, the average feed speed of butter fish and jelly fish is 1,400 mm/s when the roller rotation speed is 300 rpm, 1,480 mm/s at 600 rpm, and 1,850 mm/s at 900 rpm. A Φ58 mm roller rotates once it moved about 1.23 mm. In the future, a follow-up study of quantitative evaluation is needed targeting more non-target fish species of anchovy boat seine.

국내 건설현장에서 장스팬 구조물이 증가함에 따라 콘크리트와 강재를 조합한 충전형합성보의 적용이 증가하고 있 다. 충전형합성보는 경제적이며 시공성이 향상되고 콘크리트 축열효과에 따라 내화성도 우수하다. 충전형합성보 내부에 휨성능 을 향상시키기 위해 Re-bar로 보강하여 사용한다. 이는 콘크리트 균열에 의해 부식 되어 내력저하를 유발한다. CFRP Re-bar는 경량이며 내부식성이 우수하다. 그러나 임계온도가 250℃로 낮기 때문에 화재에 취약으로 적절한 내화피복재를 적용해야된다. 따라서 열전달해석을 통해 내부 CFRP Re-bar가 보강된 충전형합성보의 온도분포를 확인하였다. 온도 상승에 따른 휨내력을 산 정하여 피복두께를 제안하고자 한다. 해석결과 단면크기에 상관없이 콘크리트 피복두께 40mm와 뿜칠내화피복재 20mm를 적용 하면 표준화재에서 3시간 내화성능을 확보하는 것으로 평가되었다.

경주 및 포항 지진으로 인한 수도관의 파열 및 누수로 배관 시스템용 신축이음부의 내진 안전성 확보가 강조되고 있 다. 일반적으로 금속 벨로우즈에 스테인리스강을 이용한 금속 벨로우즈가 사용되며 목적에 따라 다양한 주름 형상과 단층 및 다층 형태로 제작된다. 그러나 벨로우즈의 불규칙한 산의 형상에 대한 휨 거동 및 피로 파괴에 대한 연구는 미비하다. 본 연구 에서는 벨로우즈의 불규칙한 산의 형상을 고려한 휨 거동을 검토하기 위하여 단조시험, 준정적 반복재하시험 및 피로시험을 수 행하였다. 시험을 위해 제작된 벨로우즈는 단층(1ply)과 다층(3ply)으로 제작되었다. 다층 벨로우즈의 최대하중과 최대변형이 단 층 벨로우즈보다 크게 평가되었다. 단층 벨로우즈는 산과 산 사이에서 파괴가 되었으며, 다층 벨로우즈의 경우에는 산에서 파괴 가 발생하였다. 주름의 높이와 전체 두께가 다른 벨로우즈의 휨 파괴 거동을 평가하였으며, 단층의 초기 피로 균열은 고정 플랜 지와 첫 번째 산의 곡률에서 관찰되었다. 다층의 경우에는 첫 번째 산과 두 번째 산 사이의 곡률에서 관찰되었다.

PURPOSES : Unlike European standards, domestic performance assessment standards for truck mounted attenuators (TMAs) was first stipulated in 2014 using the NCHRP Report 350 of 1993 as the standard instead of the 2009 MASH of the United States. The purpose of this study is to present an improvement in the domestic performance evaluation criteria for TMAs.. METHODS : Considering the latest TMA performance evaluation standards in the U.S. and Europe, domestic performance evaluation criteria must improve stipulations related to impact speeds, impact conditions, impact cars, and support trucks. The performance change in the TMAs according to the variation in the impact speed, impact condition, impact vehicle, and support vehicle was investigated using finite element analysis (FEA). RESULTS : The TMA for an impact speed of 100 km/h showed a limit to the safety of the occupants of the collision vehicle and workers on the road for a collision speed of 120 km/h. The safety of the workers on the road was also not guaranteed for the collision of the remaining 73.8% of vehicles that exceeds the maximum impact car weight of 1,300 kg, the lower 26.2% of the total mass composition of domestic passenger cars. In addition, a TMA that satisfied only the conditions under which the vehicle was hit head-on to the center of the TMA did not reduce the risk of a secondary collision of the impact vehicle. Furthermore, the safety of workers on the road was not guaranteed when a travel distance of a support truck of 10 tons or more was applied to a work vehicle of less than 10 tons. CONCLUSIONS : To improve the safety of road traffic, a performance level corresponding to an impact speed of 120 km/h was added to the domestic TMA performance evaluation standard, and the eccentricity and oblique collision conditions were mandatory. Furthermore, the maximum impact vehicle weight of 1300 kg was raised to 2000 kg, and the test requester had to present support trucks of lower and upper weights such that TMA mounting trucks of various weights could be used.

PURPOSES : This study describes the experimental findings on the mechanical properties of calcium aluminate cement (CAC)-based repair mortars with or without natural cellulose fiber (NCF). Additionally, the effect of adding NCF to the reduction of fugitive dust in the CAC powder was examined. METHODS : To produce mortar, four different levels of NCF (0.0.5, 1.0, and 2.0% by binder weight) were adopted, and the water-binder ratio was fixed at 0.485. The flow, strength characteristics, absorption, and surface electrical resistivity of the mortars were measured at predetermined periods. Additionally, SEM observations were performed to examine the microstructural changes and hydrates formed on the 28 day-mortar samples. RESULTS : The addition of NCF led to a decrease in fugitive dust. Regarding the mechanical properties of the mortars, that with 0.5% NCF exhibited a better performance in terms of strength development and surface electric resistivity compared to those of other mortars. However, the addition of NCF was less effective in the enhancement of the absorption of mortars. Further, we discovered that the microstructures of the mortars with additional NCF were comparatively dense compared to those without NCF. CONCLUSIONS : The appropriate addition of NCF can enhance the performance of CAC-based repair materials. However, further studies on the durability of CAC with the addition of NCF are needed to determine the optimal mixture.

In order to develop greenhouse cooling and water saving technologies suitable for desert climate, the performance evaluation of the cooling packages and condensate water recovery from cooling fan coil unit. As a result of the application for tomato greenhouse in summer, the root zone temperature of root zone cooling+duct cooling case and root zone cooling case was 25℃ during the day and 20℃ at night, which was suitable for tomato growth. When the nutrient solution tank was cooled, the temperature of the nutrient solution was maintained at 20 degrees, but otherwise, the temperature exceeded 30℃, causing the root zone temperature to rise. Condensate water recovery per fan coil unit was 93L on average per day in August, and was proportional to relative humidity in greenhouse and temperature difference between dew point temperature and the surface temperature of heat exchanger. Tomato growth was found to be improved in the order of root zone cooling+duct cooling, root zone cooling, duct cooling and control. It was analyzed that the yield of root zone cooling+duct cooling, root zone cooling and duct cooling increased by 35%, 28% and 11%, respectively, compared to the control.

지구 대기에 영향을 주는 거의 모든 인간활동과 자연현상을 수치적으로 담아내는 지구시스템모델은 기후 위기 의 시대에 활용될 가장 진보한 과학적 도구이다. 특히 우리나라 기상청이 도입한 지구시스템모델인 Unified Model (UM)은 지구 대기 연구의 과학적 도구로써 매우 활용성이 높다. 하지만 UM은 수치 적분과 자료 저장에 방대한 자원 이 필요하여 개별 연구자들은 최근까지도 기상청 슈퍼컴퓨터에만 UM을 가동하는 상황이다. 외부와 차단된 기상청 슈 퍼컴퓨터만을 이용하여 모델 연구를 수행하는 것은 UM을 이용한 모형 개선과 수치 실험의 원활한 수행에 있어 효율성이 떨어진다. 본 연구는 이러한 한계점을 극복할 수 있도록 개별 연구자가 보유한 고성능 병렬 컴퓨터(리눅스 클러스터) 에서 최신 버전 UM을 원활하게 설치하여 활용할 수 있도록 UM 시스템 환경 구축 과정과 UM 모델 설치 과정을 구 체적으로 제시하였다. 또한 UM이 성공적으로 설치된 리눅스 클러스터 상에서 N96L85과 N48L70의 두 가지 모형 해 상도에 대하여 UM 가동 성능을 평가하였다. 256코어를 사용하였을 때, 수평으로 1.875o ×1.25o(위도×경도)와 수직으로 약 85 km까지 85층 해상도를 가진 N96L85 해상도에 대한 UM의 AMIP과 CMIP 타입 한 달 적분 실험은 각각 169분 과 205분이 소요되었다. 저해상도인 3.75o ×2.5o와 70층 N48L70 해상도에 대해 AMIP 한달 적분은 252코어를 사용하여 33분이 소요되는 적분 성능을 보였다. 또한 적분을 위해 사용된 코어의 개수에 비례하여 적분 성능이 향상되었다. 성능 평가 외에 29년 간의 장기 적분을 수행하여 과거 지상 2-m 온도와 강수 강도를 ERA5 재분석자료와 비교하였고, 해상 도에 따른 차이도 정성적으로 살펴보았다. 재분석자료와 비교할 때, 공간 분포가 유사하였고, 해상도와 대기-해양 접합 에 따라 모의 결과에서 차이가 나타났다. 본 연구를 통해 슈퍼컴퓨터가 아닌 개별 연구자의 고성능 리눅스 클러스터 상에서도 UM이 성공적으로 구동됨을 확인하였다.