Electricity is generated by the combined reactions of hydrogen oxidation and oxygen reduction which occur on the Pt/C catalyst surface. There have been lots of researches to make high performance catalysts which can reduce Pt utilization. However, most of catalysts are synthesized by wet-processes and a significant amount of chemicals are emitted during Pt/C synthesis. In this study, Pt/C catalyst was produced by arc plasma deposition process in which Pt nano-particles are directly deposited on carbon black surfaces. During the process, islands of Pt nano-particles were produced and they were very fine and well-distributed on carbon black surface. Compared with a commercialized Pt/C catalyst (Johnson & Matthey), finer particle size, narrower size distribution, and uniform distribution of APD Pt/C resulted in higher electrochemical active surface area even at the less Pt content.

In this study, SAP (Sliding Arc Plasma) was applied to remove ammonia, an odor causing substance under various conditions. From the study, it was found that the SAP angle is related with the plasma radius. As the angle became narrower, the radius became shorter while the plasma became stronger. Results within 30° angle of the electrode and the electrode length of 10 cm or more and the electrode spacing shows high efficiency at 2mm. In short, it was empirically proved that the ammonia removal efficiency increased at the limited plasma range.

MAO(Micro-Arc Oxidation) method was used to make surface on 6063 Al specimen. This study was focused on an influence of voltage, density of electrolyte and a period of treatment on the change of surface microstructure by using SEM(Scanning Electron Microscope), EDS(Energy Dispersive X-ray Spectroscopy). The microstructure shows higher roughness and thicker oxidized layer with increase of voltage and maintaining period of treatment. The density of electrolyte affected a formation of more dense surface and increase of a oxidized layer.

Carbon nanotubes are unique tubular structures of nanometer diameter and large length/diameter ratio. The nanotubes may consist of one up to tens and hundreds of concentric shells of carbons with adjacent shells separation of ~0.34 nm. Multiwalled carbon nanotubes were synthesized by arc-discharge technique. MWCNTs were formed at the cathode deposit along with other carbonaceous materials like amorphous carbon, graphite etc. However, to get the best advantage of carbon nanotubes in various advanced applications, these undesired carbonaceous materials to be removed which is a challenging task. In the present study, various techniques were tried out for purifying MWCNTs such as physical filtration, chemical treatment and thermal annealing. SEM, FTIR, TGA and BET techniques were used to characterize the CNTs at various stages. Results shows that suitable chemical treatment followed by thermal annealing under controlled flow of oxygen gives the better route for purification of carbon nanotubes.

Inconel 718 alloy has excellent mechanical properties at room temperature, high temperature and cryogenic conditions. UTS of base metal is about 900MPa at room temperature; this is increased up to 1300MPa after heat treatment & aging-hardening. Mechanical properties of Inconel 718 Alloy were similar to those shown in the the results for tensile test; mechanical properties of Inconel 718 alloy's GTAW were similar to those of base metal's properties at room temperature. Mechanical properties at cryogenic conditions were better than those at room temperature. Heat-treated Inconel 718, non- filler metal GTAW on Inconel 718 and GTAW used filler metal on Inconel 718's UTS was 1400MPa at cryogenic condition. As a result, the excellent mechanical properties of Inconel 718 alloy under cryogenic conditions was proved through tensile tests under cryogenic conditions. In addition, weldability of Inconel 718 alloy under cryogenic conditions was superior to that of its base-metal. In this case, UTS of hybrid joint (IS-G) at -100˚C was 900MPa. Consequently, UTS of Inconel 718 alloy is estimated to increase from -100˚C to a specific temperature below -100˚C. Therefore, Inconel 718 alloy is considered a pertinent material for the production of Lox Pipe under cryogenic conditions.

The Yongdong basin developed during Early Cretaceous in the central part of the Korean Peninsula and bounded on the northwest and southeast by northeast trending mega-scale strike-slip Yongdong Fault. An 8 km thick succession of exclusively terrigeneous sediments can be grouped into two mega-sequences. In concert with the migration of depocenter, the upper sequence overlaps the lower and occupies northern part of the basin during basin evolution. Alluvial and lacustrine environments were predominantly formed from early to late stage of the basin formation. Several lines of evidence support that the basin was formed within intra-arc tectonic environments and destroyed by polyphase tectonic force. Schematic evolutionary diagram of the basin is proposed.

The present study focused on the synthesis of a bismuth-antimony-tellurium-based thermoelectric nanopowders using plasma arc discharge process. The chemical composition, phase structure, particle size of the synthesized powders under various synthesis conditions were analyzed using XRF, XRD and SEM. The powders as synthesized were sintered by the plasma activated sintering. The thermoelectric properties of sintered body were analyzed by measuring Seebeck coefficient, specific electric resistivity and thermal conductivity. The chemical composition of the synthesized Bi-Sb-Te-based powders approached that of the raw material with an increasing DC current of the are plasma. The synthesized Bi-Sb-Te-based powder consist of a mixed phase structure of the , and phases. This powder has homogeneous mixing state of two different particles in an average particle size; about 100nm and about 500nm. The figure of merit of the sintered body of the synthesized 18.75 wt.%Bi-24.68 wt.%Sb-56.57 wt.%Te nanopowder showed higher value than one of the sintered body of the mechanically milled 12.64 wt.%Bi-29.47 wt.%Sb-57.89 wt.%Te powder.

A simple method to deposit carbon nanotube films uniformly on large area substrates using an arc discharge method is reported in this paper. The arc discharge method was modified to deposit carbon nanotube films in situ on the substrates. The substrates were scanned several times over the arcing point for a uniform film thickness. Deposition was carried out under variable dc bias conditions at 600 torr of H2 gas. The thickness uniformity of the single-wall carbon nanotube films as characterized by a four-point probe was within 30% deviation. The morphology and crystal quality of the single-wall carbon nanotube film were also characterized by field emission scanning electron microscopy and Raman spectroscopy.

대공간 구조물은 3차원적인 힘의 흐름과 면내력에 의해 외부하중에 대한 저항 능력을 극대화 시킨 형태 저항 구조로서, 일반적인 골조와는 달리 부재에 대한 유한 변형을 동반 하므로 정적, 동적 해석에 관계없이 비선형 해석이 요구 된다. 대공간 구조물의 정확한 구조 해석을 수행하기 위해서는 기하학적 비선형 및 재료적 비선형 뿐 아니라 두 효과를 함께 고려한 비선형 해석이 필요하다. 기하학적 비선형 문제가 구조재료의 특성 및 위치에 따른 비선형을 고려하지 못하고, 구조재료의 비선형 문제가 기하학적 형상에 따른 비선형을 고려하지 못한다는 상호간의 단점을 해결하기 위하여, 본 논문에서는 유한요소법으로 기하학적 비선형을 고려한 비선형 평형방정식을 적용하고, 부재의 응력-변형률 관계를 이용하여 재료적 비선형성도 함께 고려하였다. 사용된 수치해석 기법은 불안정 경로의 해를 찾아갈 수 있는 호장법을 적용하여 하중-변위 곡선을 추적하였다. 본 연구의 수치 해석결과 제시한 평면 트러스의 비탄성 비선형 거동을 정확하고 효율적으로 예측 가능한 것으로 나타났다.

The present study was focused on the synthesis of a zirconium-based alloyed nanopowder by the plasma arc discharge process. The chemical composition, phase structure, particle size and hydrogen sorption property of the synthesized powders under various synthesis conditions were analyzed using XRF, XRD, SEM, XPS and the ASTM-F798 method. The chemical composition of the synthesized Zr-V-Fe-based powders approached that of the raw material with an increasing hydrogen fraction in the powder synthesis atmosphere. The synthesized powder consist of a mixed phase structure of the phases. This powder has an average particle size of about 20 nm. The synthesized nanopowder showed getter characteristics, even though it had a lower hydrogen sorption speed than the getter powder. However, the synthesized Zr nanopowder with an average particle size of 20 nm showed higher hydrogen sorption speed than the getter powder.

Correlations between in-flight particle, splat and coating microstructure of thermally sprayed Ni20Cr were investigated. Flame spray and arc spray systems were employed for spraying Ni20Cr powder and Ni20Cr wire, respectively. The results showed that the arc spray process produced a broader size distribution for both in-flight particles and splats compared to flame process. Flower-like splat morphology was obtained from the arc spray whereas a pancake-like splat was obtained by flame spray. Ni20Cr coating sprayed by arc process had a denser microstructure, lower porosity and better adhesion at the interface.

In the present study, ultrafined Zr-V-Fe based alloy powder prepared by a plasma arc discharge process with changing process parameters. The chemical composition of synthesized powder was strongly influenced by the process parameters, especially the hydrogen volume fraction in the powder synthesis atmosphere. The synthesized powder had an average particle size of 50 nm. The synthesized Zr-V-Fe based particles had a shell-core structure composed of metal in the core and oxidse in the shell.

The nano-sized Fe powders were prepared by plasma arc discharge process using pure Fe rod. The microstructure and the sintering behavior of the prepared nanopowders were evaluated. The prepared Fe nanopowders had nearly spherical shapes and consisted of metallic core and oxide shell structures. The higher volume shrinkage at low sintering temperature was observed due to the reduction of surface oxide. The nanopowders showed 6 times higher densification rate and more significant isotropic shrinkage behavior than those of micron sized Fe powders.

A ball-shape alumina arc-tube for low-wattage lamp was developed by the PIM process. An ultra high purity translucentgrade alumina powder was used. In injection molding process, a hot-runner type mold was developed. The translucent-grade alumina powder was extremely sensitive to contamination so that the injection molding condition and atmosphere control in the furnace should be taken care of with extreme caution. Contamination sources were pinpointed with EPMA. The arc-tube was molded in half and two halves were bonded in the middle by a new bonding technique at room temperature developed in this study.

한국원자력연구소 내의 연구용 원자로(TRIGA II, III) 해체 시 발생한 방사성 알루미늄 해체 폐기물의 감용 및 제염 특성을 평가하기 위해 아크로에서 알루미늄의 용융 특성 및 방사성 핵종의 분배 특성에 대한 연구를 수행하였다. 알루미늄 폐기물은 흑연전극(graphite electrode)을 이용한 전기아크로에서 4가지 종류의 플럭스를 함께 첨가하여 용융시켰다. 또한 알루미늄의 용융 시 방사성 핵종의 분배 특성을 고찰하기 위해 알루미늄 시편에 방사성 모의 핵종인 코발트, 세슘, 스트론튬의 화합물을 오염시킨 후 혹연도가니에 넣어 알루미늄 용융실험을 수행하였다. 전기아크로에서 알루미늄의 용융실험을 수행한 결과 플럭스의 종류에 따라 다소 차이는 있으나 플럭스의 첨가에 의해 알루미늄 용융체의 유동성이 증가됨을 확인할 수 있었다. 아크 용융에 의해 생성된 슬래그의 발생량은 플럭스 A와 B를 첨가한 알루미늄 용융실험에 비해 플럭스 C와 D를 첨가한 실험에서 상대적으로 많은 양이 생성됨을 알 수 있었으며, 첨가된 플럭스의 양이 증가할수록 이에 비례하여 슬래그의 발생량이 증가함을 알 수 있었다. 슬래그(slag)의 XRD 분석을 통해 방사성 핵종이 주괴에서 슬래그 상으로 이동한 후 슬래그를 구성하고 있는 산화알루미늄과 결합하여 안정한 화합물로 슬래그 상에 포집됨을 알 수 있었다. 알루미늄 폐기물의 용융시 Co의 분배율은 플럭스를 첨가한 경우에 보다 높은 제염계수를 나타냈으며, 모든 플럭스에서 40% 이상의 제염 효과를 나타내었다. 반면에 휘발성 핵종인 Cs과 Sr은 주괴로부터 98% 이상이 제거되어 대부분이 슬래그상과 분진으로 이동되는 특성을 확인할 수 있었다.