Various carbon aerogels (CAs) were prepared from polymerization of resorcinol and formaldehyde and applied as the electrode materials of an electric double layer capacitor (EDLC) with the aim of controlling the textural and electrochemical properties of CAs by the type of base catalyst and the ratio of resorcinol to catalyst (R/C). The CAs from NaHCO3 and KHCO3 with H+ ions had higher specific surface areas but exhibited lower electrochemical properties than those from K2CO3 and Na2CO3, which had more uniform pore size distributions. The electrochemical properties of Na2CO3 were superior to those of K2CO3 probably because the polarizing power of Na+ ions was higher than K+ ions. With an increasing R/C ratio, the pore sizes of CA showed a tendency to increase but the uniformity of the pore size distribution got worse. For the four base catalysts, the highest electrochemical property was obtained at the R/C ratio of 500.

Fe3O4/Fe/graphene nanocomposite powder is synthesized by electrical wire explosion of Fe wire and dispersed graphene in deionized water at room temperature. The structural and electrochemical characteristics of the powder are characterized by the field-emission scanning electron microscopy, X-ray diffraction, Raman spectroscopy, field-emission transmission electron microscopy, cyclic voltammetry, and galvanometric discharge-charge method. For comparison, Fe3O4/Fe nanocomposites are fabricated under the same conditions. The Fe3O4/Fe nanocomposite particles, around 15-30 nm in size, are highly encapsulated in a graphene matrix. The Fe3O4/Fe/graphene nanocomposite powder exhibits a high initial charge specific capacity of 878 mA/g and a high capacity retention of 91% (798 mA/g) after 50 cycles. The good electrochemical performance of the Fe3O4/Fe/graphene nanocomposite powder is clearly established by comparison of the results with those obtained for Fe3O4/Fe nanocomposite powder and is attributed to alleviation of volume change, good distribution of electrode active materials, and improved electrical conductivity upon the addition of graphene.

Silicon alloys are considered promising anode active materials to replace Li-ion batteries by graphite powder, because they have a relatively high capacity of up to 4200 mAh/g, and are environmentally friendly and inexpensive ECO-materials. However, its poor charge/discharge properties, induced by cracking during cycles, constitute their most serious problem as anode electrode. In order to solve these problems, Si-Ge-Al alloys with porous structure are designed as anode alloy powders, to improve cycling stability. The alloys are melt-spun to obtain the rapidly solidified ribbons, and then ball-milled to make fine powders. The powders are etched using 1 M HCl solution, which gives the powders a porous structure by removing the element Al. Subsequently, in this study, the microstructures and the characteristics of the etched powders are evaluated for application as anode materials. As a result, the etched porous powder shows better electrochemical properties than as-milled Si-Ge-Al powder.

Tin is one of the most promising anode materials for next-generation lithium-ion batteries with a high energy density. However, the commercialization of tin-based anodes is still hindered due to the large volume change (over 260%) upon lithiation/delithiation cycling. To solve the problem, many efforts have been focused on enhancing structural stability of tin particles in electrodes. In this work, we synthesize tin nano-powders with an amorphous carbon layer on the surface and surroundings of the powder by electrical wire explosion in alcohol-based liquid media at room temperature. The morphology and microstructures of the powders are characterized by scanning electron microscopy, Xray diffraction, Raman spectroscopy, and transmission electron microscopy. The electrochemical properties of the powder for use as an anode material for lithium-ion battery are evaluated by cyclic voltammetry and a galvanometric dischargecharge method. It is shown that the carbon-coated tin nano-powders prepared in hexanol media exhibit a high initial charge specific capacity of 902 mAh/g and a high capacity retention of 89% after 50 cycles.

Fluorine-doped tin oxide (FTO) nanoparticles have been successfully synthesized using ultrasonic spray pyrolysis. The morphologies, crystal structures, chemical bonding states, and electrochemical properties of the nanoparticles are investigated. The FTO nanoparticles show uniform morphology and size distribution in the range of 6-10 nm. The FTO nanoparticles exhibit excellent electrochemical performance with high discharge specific capacity and good cycling stability (620mA h g−1 capacity retention up to 50 cycles), as well as excellent high-rate performance (250 mA h g−1 at 700mAg−1) compared to that of commercial SnO2. The improved electrochemical performance can be explained by two main effects. First, the excellent cycling stability with high discharge capacity is attributed to the nano-sized FTO particles, which are related to the increased electrochemical active area between the electrode and electrolyte. Second, the superb high-rate performance and the excellent cycling stability are ascribed to the increased electrical conductivity, which results from the introduction of fluorine doping in SnO2. This noble electrode structure can provide powerful potential anode materials for high-performance lithiumion batteries.

상업적으로 이용되는 폴리스티렌계 이온교환막은 제조 공정이 쉽고 간단하지만 막이 가지는 취성 때문에 내구성이 약하다는 단점을 가지고 있다. 이를 보완하기 위하여 친수성 그룹인 poly(ethylene glycol)을 곁사슬로 가지고 있는 poly(ethylene glycol)methyl ether methacrylate를 공중합시켜 음이온 교환막을 합성하였다. 지지체로는 내화학성 및 기계적 강도가 우수한 다 공성 PE 지지체를 사용하였고, 여기에 다양한 조성의 vinylbenzyl chloride, styrene, poly(ethylene glycol)methyl ether methacrylate, divinylbenzene, benzoyl peroxide를 녹인 단량체 용액을 지지체 기공에 채운 뒤 열중합 가교시켜 trimethylamine을 이 용하여 음이온 교환기를 도입해 세공충전 음이온 교환막을 합성하였다. 또한 poly(ethylene glycol)methyl ether methacrylate의 곁사슬 길이와 각 단량체가 차지하는 비율의 변화가 음이온 교환막의 전기화학적 특성에 미치는 영향을 알아보았다.

The present work reports a systematic study of using carboxymethylated cellulose (CMC) as water-bornebinder to produce Li4Ti5O12-based anodes for manufacture of high rate performance lithium ion batteries. When theLTO-to-CB-to-CMC mass ratio is carefully optimized to be 8:1:0.57, the special capacity of the resulting electrodes is144 mAh·g−1 at 10 C and their capacity retention was 97.7% after 1000 cycles at 1C and 98.5% after 500 cycles at5C, respectively. This rate performance is comparable or even better than that of the electrolytes produced using con-ventional, organic, polyvinylidene fluoride binder.

음이온 교환막의 치환체 특성을 파악하기 위하여 탄화수소의 분자구조가 다른 세 종류의 음이온 교환기를 vinyl benzyl chloride (VBC) base 막에 도입하였다. 지방족계로 trimethylamine (TMA), 고리형계로 N-methylpiperidine (MP), 방향족계로 pyridine (Py)은 아민화 반응을 통하여 도입되었다. 각각의 반응속도는 막저항(MER)과 이온교환능력(IEC) 변화의 관측으로부터 Py < MP < TMA의 순서로 반응하고 있음을 보여주었다. 한편 SEM image에서는 Py 치환체 막이 가장 균일하고 치밀한 구조를 보여주었으며, 전기화학적 특성에서도 Py이 상용막(AMX)과 비슷한 막저항(5.0 Ω·cm2 >, in 0.5 mol/L NaCl)을 나타내었다. 이 모든 결과로부터 치환체의 공명구조는 균질한 이온교환막의 제조에 기여하고 있음을 알 수 있었다.

폴리스티렌계 음이온교환막은 제조가 쉽고 공정이 간단한 장점을 갖고 있으나 막의 취성이 높아 내구성이 떨어지 는 단점을 가지고 있다. 이를 보완하여 유연하고 우수한 내구성을 갖는 막을 만들기 위해 acrylonitrile-butadiene rubber를 첨 가제로 사용하여 음이온교환막을 제조하였다. 다양한 조성의 vinylbenzylchloride와 styrene, divinylbenzene, acrylonitrile- butadiene rubber 그리고 benzoyl peroxide로 이루어진 단량체 용액을 지지체인 직물 형태의 지지체인 poly(propylene)위 에 캐스팅 후 열중합 가교시킨 다음 trimethylamine과 acetone을 이용하여 음이온 교환기(-N+(CH3)3)를 함유하는 복합막을 제 조하였다. 음이온 교환막 제조시 첨가제의 함량에 따른 막의 성능을 평가하여 최적화 비율을 찾고, 단량체의 함량을 변화하여 함수율, 이온교환용량(IEC) 및 전기저항 값을 측정하였다. 그 결과 최적화 비율로 제조된 막들은 아스톰사의 상용화 음이온 교환막(AMX)보다 높은 IEC와 낮은 전기저항 값을 나타내는 동시에 유연성과 내구성이 우수한 막이 만들어진 것을 확인할 수 있었다.

포화지방산과 인지질(DMPC)혼합 LB막에 대한 전기화학적 특성을 조사하였다. 포화지방산과 DMPC 혼합 단분자 LB막은 ITO glass에 Langmuir-Blodgett법을 사용하여 제막하였다. 전기화학적 특 성은 NaClO4 용액에서 3 전극 시스템 (Ag/AgCl 기준전극, 백금선 카운터 전극 및 LB 필름이 코팅된 ITO 작업 전극)으로 순환전압전류법을 사용하여 측정하였다. 그 결과 포화지방산과 인지질(DMPC)의 LB막은 순환전압전류도표로부터 산화전류로 인한 비가역공정으로 나타났다. 포화지방산과 인지질 (DMPC)혼합(몰비 1:1) LB막(C14, C16, C18, C20)에서 확산계수(D)는 0.05 N NaClO4에서 각각 1.2x10-3, 2.1x10-3, 1.4x10-4 및 1.1x10-3 cm2/s로 산출되었다.

The electrochemical properties of cells assembled with the LiNiO2 (LNO) recycled from cathode materialsof waste lithium secondary batteries (Li[Ni,Co,Mn]O2), were evaluated in this study. The leaching, neutralization andsolvent extraction process were applied to produce high-purity NiSO4 solution from waste lithium secondary batteries.High-purity NiO powder was then fabricated by the heat-treatment and mixing of the NiSO4 solution and H2C2O4.Finally, LiNiO2 as a cathode material for lithium ion secondary batteries was synthesized by heat treatment and mixingof the NiO and Li2CO3 powders. We assembled the cells using the LiNiO2 powders and evaluated the electrochemicalproperties. Subsequently, we evaluated the recycling possibility of the cathode materials for waste lithium secondary bat-tery using the processes applied in this work.

Carbazole과 diketopyrrolopyrrole를 기본 골격으로 한 2,5-bis-(2-butyl-octyl)-3,6-bis-[5-(4-carbazol-9-ylphenyl)-thiophen-2-yl] -2,5-dihydro-pyrrolo[3,4-c]pyrrole-1,4-dione (PCTDPP12)을 스즈키 커플링 반응을 이용하여 합성하였다. UV-Visible 분광법으로 확인 한 결과 PCTDPP의 용액과 필름의 최대 흡수 피크는 각각 643 nm와 671 nm이며, PCTDPP12의 광학적 밴드갭은 각각 1.84 eV이다. 열처리에 의해 PCTDPP12의 UV-visible 흡광도 및 최대 흡수 파장이 변화된는 것을 관찰 하였다. 그리고 순환 전압 전류법에 의해 조사한 PCTDPP12의 HOMO 및 LUMO 에너지 준위는 –5.34 eV와 -3.54 eV 이다.

순환전압전류법에 의한 인지질(sphingomyelin, SP)과 polyamic acid(PAA) 혼합물의 농도(몰비 1:1, 2:1 및 3:1)를 변화시켜 혼합단분자 LB막에 대한 전기화학적 특성을 조사하였다. SP과 PAA 혼합물의 단분자 LB막은 ITO glass에 LB법을 사용하여 제막하였다. 전기화학적 특성은 KClO₄ 용액에서 3 전극 시스템으로 측정하였다. 측정 범위는 연속적으로 1650 mV로 산화시키고, 초기 전위인 -1350 mV로 환원시켰다. 주사속도는 각각 50∼250 mV/s로 설정하였다. 그 결과 SP와 PAA 혼합물의 LB막은 순환전압전류도표로부터 환원전류로 인한 비가역공정으로 나타났다. 혼합물 LB막의 혼합(SP:PAA) 몰비가 1:1, 2:1 및 3:1에서 확산계수(D)는 각각 2.670×10-5, 3.562×10-5 및 1.005×10-5 cm²s-¹을 얻었다.

The electrochemical performance for the corrosion of zinc anodes according to particle size and shape as anode in Zn/air batteries was study. We prepared five samples of Zn powder with different particle size and morphol- ogy. For analysis the particle size of theme, we measured particle size analysis (PSA). As the result, sample (e) had smaller particle size with 10.334 µm than others. For measuring the electrochemical performance of them, we measured the cyclic voltammetry and linear polarization in three electrode system (half-cell). For measuring the morphology change of them before and after cyclic voltammetry, we measured Field Emission Scanning Electron Microscope (FE- SEM). From the cyclic voltammetry, as the zinc powder had small size, we knew that it had large diffusion coefficient. From the linear polarization, as the zinc powder had small size, it was a good state with high polarization resistance as anode in Zn/air batteries. From the SEM images, the particle size had increased due to the dendrite formation after cyclic voltammetry. Therefore, the sample (e) with small size would have the best electrochemical performance between these samples.

우리는 순환전압전류법에 의한 인지질(sphingomyelin)과 polyamic acid 혼합물의 단분자 LB막에 대한 전기화학적 특성을 조사하였다. Sphingomyelin과 polyamic acid 혼합물의 단분자 LB막은 ITO glass에 LB법을 사용하여 제막하였다. 전기화학적 특성은 KClO4 용액에서 3 전극 시스템으로 측정하였다. 측정 범위는 연속적으로 1650 mV로 산화시키고, 초기 전위인 -1350 mV로 환원시켰다. 주사속도는 각각 50, 100, 150, 200 및 250 mV/s로 설정하였다. 그 결과 sphingomyelin과 polyamic acid 혼합물의 LB막은 순환전압전류도표로부터 환원전류로 인한 비가역공정으로 나타났다. Sphingomyelin과 polyamic acid 혼합물 LB막에서 전해질농도가 0.1N과 0.2N에서 확산계수(D)는 각각 2.67cm2s-1×105과 5.23cm2s-1×106을 얻었다.

우리는 순환전압전류법에 의한 폴리이미드와 인지질혼합 나노LB 필름에 대한 전기화학적 특성을 조사하였다. polyamic acid와 인지질 단분자 LB막은 ITO glass에 Langmuir-Blodgett법을 사용하여 제막하였다. 전기화학적 특성은 KClO4 용액에서 3 전극 시스템 (Ag/AgCl 기준전극, 백금선 카운터 전극 및 LB 필름이 코팅된 ITO 작업 전극)으로 순환전압전류법을 사용하여 측정하였다. 측정 범위는 연속적으로 1650 mV로 산화시키고, 초기전위인 -1350 mV로 환원시켰다. 주사속도는 각각 50, 100, 150, 200 및 250 mV/s였다. 그 결과 polyamic acid와 인지질 혼합물의 LB 필름은 순환전압전류도표로부터 환원전류로 인한 비가역공정으로 나타났다. Polyamic acid와 인지질혼합 LB막에서 확산계수(D)효과는 LAPC를 사용한 경우가 LLPC를 사용한 것 보다 확산계수 값이 적었다.

Thin film electrode consisting purely of porous anodic tin oxide with well-defined nano-channeled structure was fabricated for the first time and its electrochemical properties were investigated for application to an anode in a rechargeable lithium battery. To prepare the thin film electrode, first, a bi-layer of porous anodic tin oxides with well-defined nano-channels and discrete nano-channels with lots of lateral micro-cracks was prepared by pulsed and continuous anodization processes, respectively. Subsequent to the Cu coating on the layer, well-defined nano-channeled tin oxide was mechanically separated from the specimen, leading to an electrode comprised of porous tin oxide and a Cu current collector. The porous tin oxide nearly maintained its initial nano-structured character in spite of there being a series of fabrication steps. The resulting tin oxide film electrode reacted reversibly with lithium as an anode in a rechargeable lithium battery. Moreover, the tin oxide showed far more enhanced cycling stability than that of powders obtained from anodic tin oxides, strongly indicating that this thin film electrode is mechanically more stable against cycling-induced internal stress. In spite of the enhanced cycling stability, however, the reduction in the initial irreversible capacity and additional improvement of cycling stability are still needed to allow for practical use.

Carbon-based electric double-layer capacitors are being evaluated as potential energy-storage devices in an expanding number of applications. In this study, samples of carbon black (CB) treated at different temperatures ranging from 650℃ to 1100℃ were used as electrodes to improve the efficiency of a capacitor. The surface properties of the heat-treated CB samples were characterized by X-ray photoelectron spectroscopy and X-ray diffraction. The effect of the heat-treatment temperature on the electrochemical behaviors was investigated by cyclic voltammetry and in galvanostatic charge-discharge experiments. The experimental results showed that the crystallinity of the CBs increased as the heat-treatment temperature increased. In addition, the specific capacitance of the CBs was found to increase with the increase in the heat-treatment temperature. The maximum specific capacitance was 165 F·g-1 for the CB sample treated at 1000℃.

WCl6-EtAlCl2 촉매계를 이용하여 비교적 큰 분자량을 갖는 폴리(페닐아세틸렌)을 합성하였다. 중합반응이 잘 진행되었으며 중합수율은 81%였다. 합성한 폴리(페닐아세틸렌) 분자구조를 NMR(1H-,13C-), IR, UV-visible, 원소분석 등으로 분석한 결과 페닐 치환기를 갖는 공액구조 고분자가 합성되었음을 확인할 수 있었다. 아울러 332 nm의 빛으로 여기시킬 경우 PL 최대 peak는 424 nm에서 관찰되었는데, 이는 2.93 eV의 광 에너지에 해당한다. 이 고분자의 순환 전압전류 그림은 도핑과 탈도핑사이에서 비가역적인 전기화학적 거동을 보여주었다. 이 고분자의 전기화학적 과정이 매우 안정하였으며, 스캔속도에 따른 산화전류 밀도 실험으로부터 이 고분자의 산화-환언 과정은 확산-제어과정에 따르는 것으로 분석되었다.