Asphalt concrete(Ascon) is used to repair potholes and cracks. Special truck-mounted cargo boxes transport 200℃ asphalt concrete to repair potholes and cracks. However, long working and transportation hours to repair wide roads decrease the temperature of the asphalt concrete inside the cargo boxes. If the asphalt concrete temperature drops below 170℃, the adhesion with roads that need repair decreases. Therefore, the temperature of the asphalt concrete needs to be maintained for a long time. Conventional asphalt concrete cargo boxes are mostly burner-type models using hot air to prevent the temperature of the asphalt concrete from dropping. However, there are significant temperature differences between the asphalt concrete near and far away from the hot air, so the temperature decreases over time and leads to the disposal of large amounts of asphalt concrete. This causes waste of resources and environmental pollution. Therefore, this study proposed a heat dissipation cut-off type cargo box model to solve this problem and demonstrated its performance over conventional burner-type models through tests and analysis.

Double slug interaction in downward-facing nucleate boiling was studied to investigate its effect on boiling performance. Two heating surfaces were individually controlled to apply heat flux while their boiling performance were measured. A slug generated from upper heater affect on lower heater to make convectional flow by suction following departure of slug. Moreover, it showed to reduce hovering time of slug bubble on lower heater because it could help bubble departure on lower heater. Meanwhile, a slug generated from lower heater affected on upper heater to make convectional flow by sweeping. However, it showed to increase hovering time of slug bubble on upper heater, because they collapsed to each other. So, the slugs from lower heater enhanced the boiling performance of upper heater with low heat flux condition, but reduced the performance of it with high heat flux condition.

In the powder bed fusion (PBF) process, a 3D shape is formed by the continuous stacking of very fine powder layers using computer-aided design (CAD) modeling data, following which laser irradiation can be used to fuse the layers forming the desired product. In this method, the main process parameters for manufacturing the desired 3D products are laser power, laser speed, powder form, powder size, laminated thickness, and laser diameter. Stainless steel (STS) 316L exhibits excellent strength at high temperatures, and is also corrosion resistant. Due to this, it is widely used in various additive manufacturing processes, and in the production of corrosion-resistant components with complicated shapes. In this study, rectangular specimens have been manufactured using STS 316L powder via the PBF process. Further, the effect of heat treatment at 800 °C on the microstructure and hardness has been investigated.

PURPOSES : Steel deck bridges are the preferred structural type for reducing dead load, and the use of thin-layer asphalt concrete with excellent adhesion to the steel deck and excellent deformation followability is increasing for bridge pavements. However, because these materials are constructed at a high temperature of 240 °C or higher to maintain high fluidity during construction, excessive thermal deformation and stress may be temporarily induced in the steel deck. Therefore, the stability of the structure must be assessed by considering the environmental conditions of the site during pavement construction. Herein, a method is presented for estimating the heat source equation, in which conduction and convection effects are removed using temperature measurement data, for modeling U-rib using plate elements. The validity of the study is assessed by deriving the equivalent heat source equation using the temperature data measured from the underside of the steel deck while constructing a 40-mm-thick goose asphalt concrete pavement layer on a 12-mm-thick steel deck. In addition, the practicality is verified by performing heat transfer and thermal stress analyses. METHODS : By comparing the temperature data measured during the construction of high-fluidity asphalt concrete with the results of repeated heat transfer numerical analysis, heat source data without field conduction and convection conditions are obtained. Subsequently, a heat source equation suitable for the heat source data is derived using the least-squares method. RESULTS : The results of the heat transfer analysis using the equivalent heat source equation calculated using the presented method are almost consistent with the measured temperature data. In addition, the behavioral characteristics of the structure that matches the behavior of the actual structure can be derived through thermal stress analysis, which considers heat conduction and convection to adjacent members. CONCLUSIONS : Even when the steel deck and U-rib member are modeled as plate elements, thermal effect analysis can be performed reasonably while considering field conditions.

Lonicera caerulea (Honey berry, HB) has been used in medical treatment in Russia, Japan, China and Korea. It has high level of vitamin C and polyphenolics. Polyphenolics can improve anti-inflammatory effect and prevent cancer, diabetes mellitus type 2. Also, Vitamin C is a representative anti-oxidant. however, it is still unknown what effect it will have on the oxidation stress of the reproductive system. In previous studies, ROS can be produced when it is exposed to heat stress and has negative effect on sperm’s maturation, capacitation, hyperactivation, acrosome reaction and fusion of egg and sperm. Therefore, the purpose of this study is to investigate the antioxidant effects of L. Caerulea on the sperm and mice. At first, it conducted using ICR mouse (n = 20) for 4 weeks. There are four groups of mice (n = 5 per group). Also, L. Caerulea was taken by oral gavage. Group I (control) kept at 23℃-27℃ and administer D.W (0.5 mL/day), Likewise, Group II (HB) kept at room temperature but gave HB (250 mg/kg, 0.5 mL/day), Group III (HB + HS) received heat stress (40℃) using hyperthermia induction chamber and gave HB at same dose. and Group IV (HS) exposed heat stress only. Mainly, we showed degree of gene expression using Western blot in SOD, HSP 70, 17β-HSD and Real-time PCR. It can find correlation between intracellular activity like steroid hormone, apoptosis under ROS and antioxidant activity of L. Caerulea.

In this study the effect of vitamin C administration on pregnancy rates during summer heat stress in dairy cows was examined. A total of 80 Holstein-Friesian cows were divided into control and treatment groups (n = 40 each). Control group animals were given 10 mL isotonic normal saline, and treatment group, Vitamin C (4 mg/kg) on artificial insemination day (day 0) and 4th, 8th and 12th day post insemination. Pregnancy diagnosis was performed on 30th day post insemination by ultrasonography. Blood samples were randomly taken from 11 animals from each group. Serum P4, GSH, MDA and plasma 8-OHdG levels were determined by using ELISA method. Results showed that 8-OHdG levels were lower in treatment group on day 4, 8 and 12 (p < 0.05) compared with the control group. Similarly, pregnancy rate was higher in treatment group (32.5%) than control (22.5%), respectively. However, MDA, P4 and GSH levels were similar in both groups at 4th, 8th and 12th day. A gradual increase in P4, and MDA levels, and a strong positive correlation between 0, 4th (r = 0.54), 4, 8th (r = 0.59) and 8, 12th (r = 0.51) day was found. Similarly, GSH levels also showed positive correlation at days 0, 4th (r = 0.47) and 4, 8th (r = 0.56). However, a strong negative correlation (r = -0.56) between MDA day 0, and GSH day 8 was found. In conclusion, vitamin C application during insemination period in postpartum cows increases pregnancy rate, and reduces oxidative stress metabolite 8-OHdG levels.

In this paper, a heat exchange system using cooling dehumidification and mixing process was proposed as an experimental study for a white smoke reduction heat exchanger system under winter condition. The white smoke reduction heat exchange system is divided into an EA part, SA part, W part and mixing zone. For the operating conditions, three types (Cases 1, 2, and 3) were selected depending on whether EA fan, SA fan, and A-W heat exchanger were operated. In addition, in order to visualize the white smoke exhausted from the mixing zone, it was photographed using CCTV. In order to investigate the performance of the white smoke reduction heat exchange system, the temperature reduction rate and absolute humidity reduction rate of EA and the heat recovery rate of W were calculated. The temperature change of EA and SA according to operating conditions was most effective in Case 3, and the temperature and absolute humidity at the outlet of the mixing zone were greatly reduced. From the results of the white smoke visualization, it was confirmed that the white smoke generation mechanism was different depending on the operating conditions, and the amount of white smoke generation was greatly reduced.

This study presents a numerical modeling and a transient simulation of a desiccant coated heat exchanger (DCHE) that is employed for dehumidification in buildings. DCHE is fabricated by coating type RD silica gel on the fin surfaces of a fin tube heat exchanger. The latent cooling load, which is 25 to 45% of the total cooling load in most weather conditions is removed by adsorption of vapor using DCHE. The saturated adsorbent is then regenerated by using either low-temperature waste heat from industry and/or renewable energy such as solar energy and geothermal energy. A mathematical model is established and a transient simulation has been carried out so as to analyze its performance in terms of average humidity difference (AHD), moisture removal capacity (MRC), latent cooling capacity(QL), and COP. Comparison between the simulation results and the experimental data was carried out and showed good agreement and a similar trend with a maximum discrepancy of 5%. Key results revealed that MRC, AHD, QL, and COP are largely affected by both air dry-bulb temperate and air wet-bulb temperature while they are less affected by the frontal air velocity. Furthermore AHD, MRC and QL are largely improved by hot-water temperature while COP decreases as hot-water temperature increases due to high regeneration energy consumption.

This paper considers the influence of internal heat exchanger and capillary tube on the efficiency of small refrigeration system using eco-friendly refrigerants such as R290, R600a, R1270, and R717. A refrigeration system using such internal heat exchanger and capillary tube may improve performance, but may degrade performance. Therefore, this paper used a mathematical model in a normal state to understand performance characteristics as to what change occurs when internal heat exchanger and capillary tube are attached to eco-friendly refrigerant based on R134a. In addition, the effects of operating conditions such as refrigerant flow rate, evaporation temperature, condensation temperature, subcooling degree internal heat exchanger length and capillary tube length were analyzed. The result showed that the evaporation temperature, condensation temperature, subcooling degree, internal heat exchanger length and capillary tube length had an effect on the refrigeration capacity and compression power. Therefore, it is necessary to design a refrigeration cycle using an eco-friendly refrigerant by grasping these effects in detail.

In order to study the drying performance of the dryer, the performance characteristics of the heat pump dryer applied a PF heat exchanger is applied were experimentally investigated. The capacity, COP, drain and SMER of the dryer were measured by the refrigerant charge and EEV opening. Heat pump dryers are refrigerant-air systems. For the dryer performance test, an air enthalpy calorimeter was used. From the experimental results, the heat exchanger performances according to the change in the refrigerant charge and EEV opening were the maximum at 0.5kg refrigerant and 30% EEV opening, respectively. In addition, SMER suggested a satisfactory level of drying performance. This shows that the refrigeration cycle of the dryer must be operated at an appropriate refrigerant amount and EEV opening degree to secure optimal drying performance. On the other hand, the time to reach the target setting temperature of the dryer was increased by about 2.5 times depending on with/without the sample.

본 연구는 중학생들이 온실 효과와 지구 온난화를 이해하고, 이를 지구 복사 평형 관점에서 설명할 수 있는지 심층적으로 살펴보고자 하였다. 이를 위해 ‘대기권과 날씨’ 대단원 수업을 완료한 중학교 3학년 118명의 학생을 대상으로, 복사 평형, 온실 효과, 지구 온난화에 대한 선택형 및 서답형으로 구성된 학생 이해 온라인 평가를 2021년 7월 13 일부터 7월 24일까지 실시하였다. 최종적으로 97명의 학생 응답을 수집하여 분석한 결과, 과반수(61.9%)가 넘는 학생들이 복사 평형의 의미를 옳게 기술하였으나 제시된 자료와 무관하게 사전 지식이나 구체적 사례를 들어 설명하는 경우가 많았다. 대부분의 학생들(92.8%)은 대기가 있는 지구에서 온실 효과가 나타나는 것을 알고 있었지만, 온실 효과를 복사 평형이 깨진 상태로 생각하는 경향이 높았으며(32.0%), 달과 지구 모두 복사 평형이 일어난다고 응답한 학생 (47.4%)은 절반에 미치지 못했다. 온실 효과의 원인으로 대기의 재복사를 찾아낸 학생은 다수(69.1%)였으나, 지구로 입사한 태양 복사량보다 방출한 지표 복사량이 더 크다고 응답한 학생은 소수(39.2%)에 불과하였다. 또한 절반 정도의 학생들(49.5%)이 온실 기체의 증가와 대기 흡수, 이로 인한 지표로의 재복사의 관계를 잘 이해하고 있었다. 그러나 온실 기체가 증가할 때, 지표 방출에 대해서는 증가(14.4%), 일정(9.3%), 감소(7.2%), 무응답(18.6%)으로 의견이 매우 다양하게 나타났다. 복사 평형, 온실 효과, 지구 온난화는 지구계의 균형과 상호작용이라는 빅 아이디어로 연결된 커다란 하나의 의미망이므로 학생들이 지구 온난화로 인한 기후 변화를 이해하고 적용하고 해석하는 개념 체계가 될 수 있다. 따라서 현재 인류에 닥친 기후 변화 위기와 관련해 학생들이 정확한 이해에 근거하여 과학적으로 사고하고 과학적 개념을 정립할 수 있도록, 정교한 프로그램 개발과 수업 경험을 제공하고 그 효과를 점검하는 후속 연구가 진행되어야 할 것이다.

This review summarizes the recent progress in iron-oxide-based heat generators. Cancer treatment using magnetic nanoparticles as a heat generator, termed magnetic fluid hyperthermia, is a promising noninvasive approach that has gained significant interest. Most previous studies on improving the hyperthermia effect have focused on the construction of dopant-containing iron oxides. However, their applications in a clinical application can be limited due to extra dopants, and pure iron oxide is the only inorganic material approved by the Food and Drug Administration (FDA). Several factors that influence the heat generation capability of iron-oxide-based nanoparticles are summarized by reviewing recent studies on hyperthermia agents. Thus, our paper will provide the guideline for developing pure iron oxide-based heat generators with high heat dissipation capabilities.

In this study, multilayered SnO nanoparticles are prepared using oleylamine as a surfactant at 165oC. The physical and chemical properties of the multilayered SnO nanoparticles are determined by transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Interestingly, when the multilayered SnO nanoparticles are heated at 400oC under argon for 2 h, they become more efficient anode materials, maintaining their morphology. Heat treatment of the multilayered SnO nanoparticles results in enhanced discharge capacities of up to 584 mAh/g in 70 cycles and cycle stability. These materials exhibit better coulombic efficiencies. Therefore, we believe that the heat treatment of multilayered SnO nanoparticles is a suitable approach to enable their application as anode materials for lithium-ion batteries.

The precipitation effect of Al-6%Si-0.4%Mg-0.9%Cu-(Ti) alloy (in wt.%) after various heat treatments was studied using a laser flash device (LFA) and differential scanning calorimetry (DSC). Solid solution treatment was performed at 535 oC for 6 h, followed by water cooling, and samples were artificially aged in air at 180 oC and 220 oC for 5 h. The titanium-free alloy Al-6%Si-0.4%Mg-0.9%Cu showed higher thermal diffusivity than did the Al-6%Si-0.4%Mg-0.9%Cu-0.2%Ti alloy over the entire temperature range. In the temperature ranges below 200 oC and above 300 oC, the value of thermal diffusivity decreased with increasing temperature. As the sample temperature increased between 200 oC and 400 oC, phase precipitation occurred. From the results of DSC analysis, the temperature dependence of the change in thermal diffusivity in the temperature range between 200 oC and 400 oC was strongly influenced by the precipitation of θ'-Al2Cu, β'-Mg2Si, and Si phases. The most important factor in the temperature dependence of thermal diffusivity was Si precipitation.

The effect of heat treatment and vacuum conditions on the textural properties and electrochemical performance of commercially available activated carbons (ACs) was investigated. The AC after post-heat treatment was characterized by nitrogen adsorption–desorption, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy measurements. The ACs treated under vacuum conditions exhibit a higher specific surface area and micropore surface area than those treated under nitrogen atmospheric pressure without significantly affecting the graphite structure of the AC. Under 800 °C temperature and vacuum conditions (AC-V800), the AC with the highest Brunauer– Emmett–Teller surface area of 1951.9 m2 g−1 (16.4% improvement relative to that of the original AC (1677.2 m2 g−1)) was obtained. This is attributed to the removal of oxygen-containing functional groups and volatile matters in the carbon by thermal treatment under vacuum conditions. Consequently, the electric double-layer capacitor using ACs treated under vacuum conditions (1 kPa) at 800 °C (AC-V800) shows considerably improved electrochemical performance in terms of higher specific capacitance and better cycling stability at a high working voltage (3.1 V), compared to the nitrogen-treated and commercial ACs.

본 연구에서는 CO2 가스 배출 저감 및 선박 폐열 회수 증대를 목적으로 선박 배기로 버려지는 폐열을 전기로 변환하는 ORC(Organic Rankine Cycle) 발전에 대해 시뮬레이션을 통한 냉매별 효율을 보여주고 있다. 상대적으로 고온인 배기가스의 폐열과 상대적으로 저온인 냉각해수를 이용하여 Aspen HYSYS 11을 이용하여 시뮬레이션을 수행하였다. 해수냉각 ORC 발전시스템의 시뮬레이션 결과, 작동유체 효율은 R717 냉매가 2.86 %로 가장 높았고, 다음 순으로 R152a, R134a, R143a, R125a로 나타났다.