Recently, the demand for shape memory alloys in the biomedical industry is increasing. Nitinol alloy, which accounts for most of the shape memory alloy market, occupies most of the biomedical field. Nitinol for biomaterials requires a clean surface without sub-micron surface integrity and surface defects in order to be used more safely in a living body. Among them, new technologies such as polishing using MR fluid are being studied, but there is a disadvantage in that it takes a long time for processing due to a low material removal rate. In this study, material removal studies were conducted for effective polishing, and excellent polishing properties of MR fluid were confirmed.

PURPOSES : Traffic volume, an important basic data in the field of road traffic, is collected from traffic survey equipment installed at certain locations, which sometimes results in missing traffic volume data and abnormal detection. Therefore, this study presents various missing correction techniques using traffic characteristic analysis to obtain accurate traffic volume statistics. METHODS : The fundamental premise behind the development of a traffic volume correction and prediction model is to set the corrected data as the reference value, and the traffic volume correction and prediction process for the outliers and missing values in the raw data were performed based on the set values. RESULTS : The simulation results confirmed that the algorithm combining seasonal composition, quantile AD, and aggregation techniques showed a detection performance of more than 91% compared with actual values. CONCLUSIONS : Raw data collected due to difficulties faced by traffic survey equipment will result in missing traffic volume data and abnormal detection. If these abnormal data are used without appropriate corrections, it is difficult to accurately predict traffic demand. Therefore, it is necessary to improve the accuracy of demand prediction through characteristic analysis and the correction of missing data or outliers in the traffic data.

Titanium, which has excellent strength and toughness characteristics, is increasingly used in the aerospace field. Among the titanium alloys used for body parts, more than 80 % are Ti-6Al-4V alloys with a tensile strength of 931 MPa. The spark plasma sintering (SPS) method is used for solidification molding of powder manufactured by the mechanical milling (MM) method, by sintering at low temperature for a short time. This sintering method avoids coarsening of the fine crystal grains or dispersed particles of the MM powder. To improve the mechanical properties of pure titanium without adding alloying elements, stearic acid was added to pure titanium powder as a process control agent (PCA), and MM treatment was performed. The properties of the MM powder and SPS material produced by solidifying the powder were investigated by hardness measurement, X-ray diffraction, density measurement and structure observation. The processing deformation of the pure titanium powder depends on the amount of stearic acid added and the MM treatment time. TiN was also generated in powder treated by MM 8 h with 0.50 g of added stearic acid, and the hardness of the powder was higher than that of Ti-6Al-4V alloy when treated with MM for 8 h. When the MM-treated powder was solidified in the SPS equipment, TiC was formed by the solid phase reaction. The SPS material prepared as a powder treated with MM 8 h by adding 0.50 g of stearic acid also formed TiN and exhibited the highest hardness of Hv1253.

The purpose of this study was to investigate the flavor characteristics of Gondre (Cirsium setidens Nakai) essential oil. The essential oil was isolated from the aerial parts of the plant by the hydrodistillation extraction method and analyzed by gas chromatography (GC) and GC-mass spectroscopy (MS). Seventy-eight (90.28%) volatile flavor components were identified in the essential oil from Gondre harvested in May. The major compounds were hexadecanoic acid (44.84%), phytol (15.57%), 6,10,14-trimethyl-2- pentadecanone (5.62%), and tertadecanoic acid (4.77%). Seventy (90.72%) volatile flavor components were identified in the essential oil from Gondre harvested in September. The major compounds were phytol (24.18%), 6,10,14-trimethyl-2-pentadecanone (15.59%), tetracosane (8.87%), 2-methyl eicosane (3.55%), 6,10,14-trimethyl-5,9,13-pentadecatrien-2-one (3.12%), dibuthyl phthalate (2.35%), and viridiflorol (2.33%). The flavor components of the essential oil from Gondre harvested in May and September were characterized by higher proportions of aliphatic fatty acids and terpene compounds, respectively.

본 연구는 부도덕한 행동 이후에 발생하는 정화행동에 대한 도덕적 평가가 행위자의 자원 가용성에 따라 달라지는지를 검증했다. 이를 위해 행위자 특성(사회경제적 수준, 신체건강 수준)을 달리하여 도덕적 정화방법(기부, 봉사)에 따른 자원 가용성을 조작했으며, 참가자들은 도덕적 정화행동에 따른 고통, 위선의 정도, 그리고 용서 가능성을 평정했다. 연구 1에서는 사회경제적 수준이 높거나 낮은 사람이 기부 혹은 봉사를 통해 도덕적 정화행동을 하는 시나리오를 제시했다. 그 결과 참가자들은 부유한 사람의 기부는 고통스럽지 않았을 것이며, 위선적이고 용서하기 어렵다고 판단했다. 연구 2에서는 신체가 건강하거나 병약한 사람이 기부 혹은 봉사를 통해 잘못을 정화하는 내용을 제시했다. 그 결과 병약한 사람의 봉사활동은 고통스러웠을 것이며, 덜 위선적이며 (다른 조건에 비해) 용서 가능성을 높게 평가했다. 매개분석 결과 연구 1, 2 모두에서 정화행동의 고통이 클수록 위선을 약하게 판단하며, 이는 용서 가능성을 높이는 매개효과가 나타났다. 이 결과들은 동일한 정화행위라도 행위자의 자원 가용성에 따라 도덕적 판단이 달라짐을 보여준다. 즉, 사람들은 도덕적 정화행동은 고통을 수반해야 하며 그렇지 않은 경우 그 행위는 위선적이며 용서하기 어렵다고 평가함을 알수 있다.

A large amount of small and medium-sized metal waste is generated during the decommissioning of nuclear power plants (NPPs). Metal waste is mostly contaminated with low-level radioactive, so it needs decontamination for self-disposal and recycling. A large amount of Organic Decontamination Liquid Waste during decontamination will be generated. The generated organic liquid waste is low in concentration, so the decomposition efficiency is low in the decomposition process. A conditioning process is necessary to concentrate at a high concentration. For effective treatment for Organic Decontamination Liquid Waste, the composition of organic liquid waste and conditioning process were analyzed. Organic acids, metal ions, radioactive nuclides, surfactants, etc. are present in the Organic Decontamination Liquid Waste, and suspended solids are sometimes generated by various reactions. According to previous studies, the concentration of organic acids including surfactants obtained results from several tens of ppm to a maximum of 1,000 ppm, so the maximum value of 1,000 ppm was assumed. For the composition and total amount of metal ions, the average value (52.7wt% Fe, 16.3wt% Ni, 15.1wt% Cr, 15.9wt% Mn) of the distribution of metal species removed by the actual decontamination process is applied, and the total amount is 1,000 ppm was assumed. As for the radionuclides, only 60Co and 137Cs, which are expected to be mainly present, were considered, and 60Co was assumed to be 2,000 Bq/g and 137Cs to be 360 Bq/g by referring to the literature. The amounts of suspended solids were assumed to be 500 ppm by referring to the characteristics of the liquid waste generated in the decontamination process of the NPPs. Based on the estimated value, a reaction formula was established and a simulated Organic Decontamination Liquid Waste was prepared. As a result of measurement using an analysis device, the composition of the estimated and simulated Organic Decontamination Liquid Waste had similar values. The conditioning and treatment process largely consists of pretreatment, conditioning, decomposition processes. Organic Decontamination Liquid Waste goes through a pretreatment process to remove impurities with large particles. In the conditioning process, treated water that has passed through the UF/RO membrane system is discharged into the environment. At this time, Concentrated water goes through a decomposition process for processing the Organic Decontamination Liquid Waste, and is discharged to the environment through a secondary RO membrane system. The conditioning process is the low-concentration Organic Decontamination Liquid Waste in the UF membrane system is forming a micelles in an RO membrane system, concentrating it to a high concentration and then go through a recirculation process in the UF membrane system. An experiment was conducted to confirm whether the concentration of surfactants occurred during the conditioning process. As a result of the experiment confirmed that the highly concentrated surfactant formed micelles and was filtered out in the UF membrane system.

Integrity evaluation scheme for Spent Fuel (SF) dry storage has been developed under transportation failure modes. This method especially considered the degradation characteristics of Spent Fuel (SF) during dry storage such as radial and circumferential hydride content, hydride volume fraction, oxide thickness, etc. Hydride and zircaloy cladding are considered as material composite system, using correlation models related to material properties. Critical Strain Energy Density (CSED) is compared with Strain Energy Density (SED), to evaluate cladding integrity. CSED serves as material characteristics, while SED can be considered as boundary condition. To calculate the CSED of cladding in the lateral failure mode, circumferential hydride concentration is used. SED is calculated considering both the bending moment and axial load. On the other hand, in the longitudinal failure case, fuel rod temperature, internal pressure, hoop stress, radial hydride concentration is used to calculate CSED. And pinch force (contact) was considered to evaluate SED. Model validations were conducted by comparing hot cell SF test and existing validated evaluation results. To separately handle normal transportation conditions from hypothetical accident conditions, SED according to stress-strain analysis results was separated into elastic and plastic regions. As a result of applying this scheme for 14×14 SF, failure probability of normal condition was zero, which is the similar result with DOE and same with EPRI. Regarding accident condition, lateral case showed similar result, but longitudinal case showed different but reasonable result, which was due to the different analysis conditions. The proposed methodology which was indigenously developed through this study is named as K-method.

Black Soldier Fly Larvae (Hermetia illucens, BSFL) is an environmental purification insect utilized as an animal feed source due to its high protein content. BSFL need to be dried to preserve quality, and the optimal drying method should be cost-effective. In this study, various drying methods (hot air (HD), freeze (FD), vacuum (VD), and combined-drying (CD)) were applied to BSFL, and then BSFL powders were characterized. Crude protein content was highest in HD and lowest in CD, and there was no significant difference in crude fat content (p>0.05). In the measurement of the total amino acid content of BSFL, glutamic acid and aspartic acid were the highest regardless of the drying method. The total amino acid content was the highest in HD and the lowest in CD. Total polyphenol content was higher in VD and FD than in HD and CD. Also, hydrogen peroxide and DPPH radical scavenging showed similar results. In the antioxidant measurement results, VD and FD showed higher antioxidant capacity, but considering cost-effectiveness, HD was the most available method for drying BSFL.

Buckling Restrained Braces can not only express the strength considered at the time of design, but also reduce the seismic load by energy dissipation according to the plastic behavior after yield deformation of the steel core. The physical characteristics and damping effect may be different according to the buckling prevention method of the steel core by the lateral restraint element. Accordingly, in this study, To compare hysteresis characteristics, Specimen(BRB-C) filled with mortar, specimen(BRB-R) combined with a buckling restraint ring and Specimen(BRB-EP) filled with engineering plastics was fabricated, and a cyclic loading test was performed. As a result of the cyclic loading test, the maximum compressive strength, cumulative energy dissipation and ductility of each test specimen was similar. But in case of the cumulative energy dissipation and ductility, BRB-C filled with the mortar specimen showed the lowest. This is considered to be because the gap between the steel core and the reinforcing material for plastic deformation was not uniformly formed by pouring mortar around the core part.

To predict the quality of Fuji apples, this study investigated the characteristics and correlations of their fruit quality according to storage method and storage period. Fuji apples were stored in cold storage at 0oC for 250 days with no treatment, with 1-MCP treatment, and under controlled atmosphere (CA) storage. According to the storage method, the weight loss was the lowest in the CA-treated group (3.43%) until 250 days, and the change in fruit firmness was the least in the 1-MCP group. The titratable acidity remained above 0.2% for 1-MCP and CA storage until 250 days and decreased to 0.1% for cold storage. The principal component analysis showed a difference in quality between the 1-MCP group, CA group, and cold storage group after 200 days of storage. Six types of volatile components were commonly detected in all storage methods, while three types of independent components with a low threshold were detected in 1-MCP. Weight loss, titrable acidity, and firmness were highly correlated with physicochemical quality, and CA storage was judged to be a long-term storage technology that satisfies consumers’ tastes by maintaining excellent flavor and quality.

Magnesium alloy is the lightest practical metal. It has excellent specific strength and recyclability as well as abundant reserves, and is expected to be a next-generation structural metal material following aluminum alloy. This paper investigated the possibility of thin plate fabrication by applying a overheating treatment to the melt drag method, and investigating the surface shape of the thin plate, grain size, grain size distribution, and Vickers hardness. When the overheating treatment was applied to magnesium alloy, the grains were refined, so it is expected that further refinement of grains can be realized if the overheating treatment is applied to the melt drag method. By applying overheating treatment, it was possible to fabricate a thin plate of magnesium alloy using the melt drag method, and a microstructure with a minimum grain size of around 12 μm was obtained. As the overheating treatment temperature increased, void defects increased on the roll surface of the thin plate, and holding time had no effect on the surface shape of the thin plate. The fabricated thin plate showed uniform grain size distribution. When the holding times were 0 and 30 min, the grain size was refined, and the effect of the holding time became smaller as the overheating treatment temperature increased. As the overheating temperature becomes higher, the grain size becomes finer, and the finer the grain size is, the higher the Vickers hardness.

Cu-doped ZnSe quantum dots were successfully synthesized in an aqueous solution using an internal doping method. The effects of ligand type, CuSe synthesis temperature, and heating time on Cu-doped ZnSe synthesis were systematically investigated. Of MPA, GSH, TGA, and NAC used as ligands, MPA was the optimal ligand as determined by PL spectrum analysis. In addition, the emission wavelength was found to depend on the synthesis temperature of the internal doping core of CuSe. As the temperature increased, the doping of Cu2+ was enhanced, and the emission wavelength band was redshifted; accordingly, the emission peaks moved from blue to green (up to 550 nm). Thus, the synthesis of Cu:ZnSe using internal doping in aqueous solutions is a potential method for ecomanufacturing of colortuned ZnSe quantum dots for display applications.

불암산성은 관련 문헌자료가 전무한 상태에서 그간 단편적인 지표조사를 바탕으로 산성 의 축조시기에 대해 단편적인 연구가 이루어지면서 축조주체에 대해 삼국시대 신라, 백제, 고구려 등 다양한 견해가 제시되고 있어 불암산성의 성격을 이해하는데 혼란을 주고 있는 실정이다. 본 고에서는 최근까지 조사된 불암산성의 축조수법을 살펴보고 이를 통해 산성의 성격을 검토해보고자 한다. 불암산성의 테뫼식 석축산성으로 축조는 지형의 이점을 최대한 이용하여 편축기법으로 쌓았으며, 방형․장방형의 화강암석재를 치석하여 바른층쌓기로 축조하였다. 일부 구간에서 기단보축이 축조되었으며, 현문식으로 축조된 남문지가 확인되었다. 이런 축조수법은 서울․ 경기 지역에 분포하는 삼국시대 산성에서 다수 확인된다. 특히 불암산성이 위치한 불암산은 양주․포천에서 서울로 진입하는 교통로상에 위치하고 있어 이를 통해 방어체계를 형성하였 음을 알 수 있다. 다만 230m의 내외의 소규모 산성으로, 집수지 등의 성내 수원이 없으며, 해발고도는 낮으나 험지에 축조되어진 점 등을 종합할 때 소규모의 병력이 주변지역을 관측 하고, 상황 발생 시 남과 북의 상황을 전달하는 통신(봉수)의 역할적의 침입시 배후를 공략 할 수 있는 전략적 기지 역할을 수행하였을 것으로 판단된다. 이와 더불어 산성내 정상부 목 곽고와 수혈 내부에서 향로 뚜껑과 훼기가 이루어진 편병 등이 수습되고 있어 군사적인 목 적의 산성으로 축조되었던 것으로 보이며, 이후 산성의 기능에 일부 제의기능이 추가된 것 으로 볼 수 있을 것이다.

Single OLED and tandem OLED was manufactured to analyze the electroluminescence characteristics of DC driving, AC driving, and full-wave rectification driving. The threshold voltage of OLED was the highest in DC driving, and the lowest in full-wave rectification driving due to an improvement of current injection characteristics. The luminance at a driving voltage lower than 10.5 V (8,534 cd/m2) of single OLED and 20 V (7,377 cd/m2) of a tandem OLED showed that the full-wave rectification drive is higher than that of DC drive. The luminous efficiency of OLED is higher in full-wave rectification driving than in DC driving at low voltage, but decrease at high voltage. The full-wave rectification power source may obtain higher current density, higher luminance, and higher current efficiency than the AC power source. In addition, it was confirmed that the characteristics of AC driving and full-wave rectification driving can be predicted from DC driving characteristics by comparing the measured values and calculated values of AC driving and full-wave rectification driving emission characteristics. From the above results, it can be seen that OLED lighting with improved electroluminescence characteristics compared to DC driving is possible using full-wave rectification driving and tandem OLED.

As the decommissioning of Kori Unit 1 progresses, securing technology for treatment and disposal of radioactive wastes that have not been disposed of so far, such as spent filters, is recognized as an urgent task. In this study, a method of confirming the disposal suitability of spent filters was presented by reviewing the waste characteristics as presented in the waste acceptance criteria (WAC). The waste characteristics to be satisfied to ensure disposal suitability of waste are largely classified into general requirements, solidification and immobilization requirements, radiological requirements, physical requirements, chemical requirements, and biological requirements. First, the general requirement is to prove that the prohibited waste form has not been introduced into items related to waste form and packaging, and to confirm the suitability of disposal through step-by-step packaging photos, generation information, X-ray inspection, and visual inspection. Second, in the solidification and immobilization requirements, spent filters are non-homogeneous waste, and if the total radioactivity concentration of nuclides with a half-life of more than 20 years is 74,000 Bq·g−1 or more, they must be immobilized. Third, in order to meet the characteristic criteria for nuclides and radioactivity concentration, sampling and scaling factors development are required and based on this, nuclides must be identified and demonstrated to be below the disposal concentration limits. Surface dose rate and surface contamination should be measured in accordance with standardized procedures and disposal suitability should be confirmed through document tests recording the measured values. Fourth, in order to satisfy the physical requirements of the particulate matter and filling rate characteristics, the spent filter must be immobilized, if necessary, thereby ensuring disposal suitability. Meanwhile, free water in the spent filter should be removed through pre-drying and dehydration, and the disposal suitability should be confirmed by applying a test. Fifth, the criteria for chelating agents should be checked for disposal suitability through operation records and component analysis of spent filters, and documents, that can prove harmful substances are removed in advance and no harmful substances are included in the package, should be provided. Lastly, in biological requirements, if the spent filters contain corrosive or infectious substances, they should be removed in advance and disposal suitability should be confirmed by providing documents that can prove that such substances are not included in the package.

2020년 경기도내 유통 중인 고춧가루의 미생물 오염도를 구매 장소, 원산지, HACCP 및 살균 여부에 따라 조사 하고, 보관방법에 따른 품질 변화를 연구하였다. 유통 중인 고춧가루 100건을 수거하여 검사한 결과 3건(대형마트 2건, 재래시장 1건)에서 Bacillus cereus가 검출되었으며, 27건(대형마트 9건, 재래시장 18건)에서 Clostridium perfringens가 검출되었다. 대형마트와 재래시장에서 수거 한 고춧가루의 일반세균수 검출량은 통계적으로 유의적인 차이는 없었으나 7 log CFU/g을 초과하는 고춧가루의 수는 대형마트보다 재래시장이 더 많았다. 보관온도(30oC, 4oC, -20oC)와 보관용기(지퍼백, 비닐봉투)에 따라 7개월까지 저장 실험한 결과, 저장 기간에 따라 미생물학적 품질 에는 큰 차이가 나타나지 않았다. 그러나 30oC에 저장한 고춧가루의 수분함량 및 ASTA color value는 저장 3개월 이후 크게 감소하였다. 따라서 고춧가루의 장기 보관 시 품질을 유지하기 위해서는 냉장고 또는 냉동고에 보관하는 것이 바람직하다고 생각된다.

This paper proposes a mathematical model that can calculate the luminescence characteristics driven by alternating current (AC) power using the current-voltage-luminance (I-V-L) properties of organic light emitting devices (OLED) driven by direct current power. Fluorescent OLEDs are manufactured to verify the model, and I-V-L characteristics driven by DC and AC are measured. The current efficiency of DC driven OLED can be divided into three sections. Region 1 is a section where the recombination efficiency increases as the carrier reaches the emission layer in proportion to the increase of the DC voltage. Region 2 is a section in which the maximum luminous efficiency is stably maintained. Region 3 is a section where the luminous efficiency decreases due to excess carriers. Therefore, the fitting equation is derived by dividing the current density and luminance of the DC driven OLED into three regions, and the current density and luminance of the AC driven OLED are calculated from the fitting equation. As a result, the measured and calculated values of the AC driving I-V-L characteristics show deviations of 4.7% for current density, 2.9% for luminance, and 1.9% for luminous efficiency.

Recently, there has been growing interest in harmful substances released from household items such as volatile organic compounds (VOCs) and this has increased people’s environmental awareness. In this study, adhesives and manicures were used as samples of indoor household goods and formaldehyde emission and tested over time under temperature conditions of 15oC, 25oC, 35oC, and 45oC. The small chamber method as the indoor air quality process test method was employed and used to evaluate the concentration of formaldehyde emissions. As a result, formaldehyde emissions gradually decreased over time in both tests using adhesives and manicures. The cumulative emission showed a logarithmic function over time, and the formaldehyde can be released for longer periods of time at lower temperature conditions. The logarithmic value and response time showed linear relationships, and it can be inferred that the formaldehyde was released from the sample through the first order reaction. Furthermore, the relationship between temperature and velocity constants which was determined using the Arenius linear equation showed that the reaction rate of formaldehyde can be estimated by a temperature change.