팔라듐이 코팅된 V53Ti26Ni21 합금 분리막을 통해 수소 투과시 혼합가스의 영향에 대해 알아보았다. 순수 수소, 수소, 이산화탄소 및 일산화탄소의 혼합가스를 공급가스로 주입할 때, 450℃, 1-3 bar의 압력에서 팔라듐이 코팅된 V53Ti26Ni21 합금 분리막의 수소 투과 실험을 수행하였다. 수소만을 공급한 투과 실험에서 팔라듐 코팅된 V53Ti26Ni21 합금 분리막(두께: 0.5 mm)의 수소 투과량은 3 bar, 450℃ 조건에서 5.36mL/min/㎠였다. 또한 수소/이산화탄소, 수소/일산화탄소 및 수소/이산화탄소/일산화탄소를 공급한 투과실험에서 V53Ti26Ni21 합금 분리막의 수소 투과량은 각각 4.46, 5.20, 3.91mL/min/㎠였다. 따라서, 수소/이산화탄소, 수소/일산화탄소 및 수소/이산화탄소/일산화탄소 혼합가스를 각각 공급할 때 투과량은 온도와 압력에 상관없이 수소 분압 감소만큼 감소하였고 모든 경우 Sievert 법칙을 잘 만족시켰다. 투과 후 분리막의 XRD 결과로부터 V53Ti26Ni21 합금 분리막은 여러 혼합가스에 대해 안정성과 내구성이 우수하다는 것을 알 수 있었다.

금속-세라믹 복합 분리막은 특히 석탄가스화 공정이나 메탄 개질에서 발생되는 혼합가스로부터 수소를 분리하기 위해 개발되어졌다. 수소투과 금속인 팔라듐과 세라믹 지지체로 Y2O3-stabilized ZrO2 (YSZ)를 이용하여 cermet 수소분리막을 제조하였다. 이렇게 제조된 분리막은 팔라듐의 연속상이 잘 발달된 치밀 구조를 보였다. Pd/YSZ 분리막의 수소 투과량은 100% 수소를 흘려 0.5~2 atm에서 측정되었다. 수소 투과량은 450℃, 2 atm에서 0.333 mL/min·㎠를 보였다. 수소 투과 후 분리막의 표면과 단면에서 균열이 형성되었다.

수소투과금속인 tantalum과 세라믹 지지체로 Y2O3-stabilized ZrO2 (YSZ)를 이용하여 cermet 수소분리막을 제조하였다. Ta/YSZ cermet 분리막은 헬륨분위기에서의 예비소결과 고진공 하에서의 본소결을 통해 제조하였으며, 소결 및 밀봉 과정에서 발생하는 불순물은 연마를 통해 제거 가능하였다. 이렇게 제조된 분리막은 tantalum의 연속상이 잘 발달된 치밀구조를 보였다. 수소 해리를 위해 팔라듐 코팅을 한 Ta/YSZ 분리막을 이용하여 200∼350°C의 범위에서 수소투과실험을 수행하였다. 300°C에서 분리막에 균열이 형성되었고 Pd 코팅층은 몇 곳이 박리되었다. XRD 결과는 tantalum이 수소와 반응하여 Ta2H가 생성되는 것을 보여주며, Ta2H에 인한 격자 팽창이 분리막의 결함을 초래하였다.

This paper describes an improved strategy for controlling the adhesion force using both the antiadhesion and adhesion layers for a successful large-area transfer process. An MPTMS (3-mercaptopropyltrimethoxysilane) monolayer as an adhesion layer for Au/Pd thin films was deposited on Si substrates by vapor self assembly monolayer (VSAM) method. Contact angle, surface energy, film thickness, friction force, and roughness were considered for finding the optimized conditions. The sputtered Au/Pd (~17 nm) layer on the PDMS stamp without the anti-adhesion layer showed poor transfer results due to the high adhesion between sputtered Au/Pd and PDMS. In order to reduce the adhesion between Au/Pd and PDMS, an anti-adhesion monolayer was coated on the PDMS stamp using FOTS (perfluorooctyltrichlorosilane) after O2 plasma treatment. The transfer process with the anti-adhesion layer gave good transfer results over a large area (20 mm × 20 mm) without pattern loss or distortion. To investigate the applied pressure effect, the PDMS stamp was sandwiched after 90˚ rotation on the MPTMS-coated patterned Si substrate with 1-μm depth. The sputtered Au/Pd was transferred onto the contact area, making square metal patterns on the top of the patterned Si structures. Applying low pressure helped to remove voids and to make conformal contact; however, high pressure yielded irregular transfer results due to PDMS stamp deformation. One of key parameters to success of this transfer process is the controllability of the adhesion force between the stamp and the target substrate. This technique offers high reliability during the transfer process, which suggests a potential building method for future functional structures.

본 연구는 방송사 PD들의 업무몰입도 결정 요인을 방송사별, PD유형별로 구분하여 살펴본 것이다. 본 연구의 주요 결과는 다음과 같다. 첫째, 방송사별 PD 업무몰입도 결정 요인을 살펴보면 KBS와 MBC간에는 비교적 유사한 결과가 나타난 반면 SBS는 차이가 있는 것으로 나타났다. KBS와 MBC PD들의 경우에는 아낌없는 격려와 지원 등과 같은 집단응집도 요인이 업무몰입도를 결정하는 핵심 요인으로 나타난 반면 SBS PD들은 조직 통제 및 제작 문화 등과 같은 조직 구성원들의 가치 요인들이 업무몰입도를 결정하는 요인으로 나타났다. 둘째, PD유형별로 업무몰입도 결정 요인을 살펴본 결과 예능 PD들의 경우에는 팀워크가 가장 중요한 요인으로 나타났으며 교양 PD들은 구성원들 간의 신뢰도가 업무몰입도를 결정하는 유의미한 요인으로 나타났다. 반면 예능 PD와 교양 PD 모두 조직 통제 요인이 부적인 방향으로 업무몰입도에 영향을 끼치는 것으로 나타났다. 특이하게 드라마 PD들의 경우 방송의 사회적 역할이나 구성원 간의 유대감 등은 부적 방향으로 업무몰입도에 영향을 끼치는 것으로 나타났다.

Carbon nanotubes (CNT) were used as a catalyst support where catalytically active Pd and Pt metalparticles decorated the outside of the external CNT walls. In this study, Pd and Pt nanoparticles supportedon HNO3-treated CNT were prepared by microwave-assisted heating of the polyol process using PdCl2 andH2PtCl6•6H2O precursors, respectively, and were then characterized by SEM, TEM, and Raman. Ramanspectroscopy showed that the acid treated CNT had a higher intensity ratio of ID/IG compared to that of non-treated CNT, indicating the formation of defects or functional groups on CNT after chemical oxidation.Microwave irradiation for total two minutes resulted in the formation of Pd and Pt nanoparticles on the acidtreated CNT. The sizes of Pd and Pt nanoparticles were found to be less than 10nm and 3nm, respectively.Furthermore, the SnO2 films doped with CNT decorated by Pd and Pt nanoparticles were prepared, and thenthe NO2 gas response of these sensor films was evaluated under 1~5ppm NO2 concentration at 200oC. It wasfound that the sensing property of the SnO2 film sensor on NO2 gas was greatly improved by the addition ofCNT-supported Pd and Pt nanoparticles.

Oridinal thermal spray process has developed into two ways, namely, temperature dominated represented by plasma spraying, and velocity dominated represented by HVOF. It is common for both that the particle materials sprayed are basically in melted or half melted condition. New process has developed recently, that is, Cold Spray and Aerosol Deposition. Particle's heating is limited in CS lower than half of the material's melting point. Moreover, exactly no heating is loaded in AD process. Through the investigation on common feature for these three spraying processes, potential of new material process - Particle Deposition, PD - is considered and proposed

The effects of different light quality on the change of membrane potential difference (PD) of the guard cell in the intact leaf have been investigated. The mombrane PD was about -5.5 mV by white light of 600 μmoles m-2 s-1. The mean PD of ch

Human embryonic stem (hES) cells can be induced to differentiate into tyrosine hydroxylase expressing (TH+) cells that may serve as an alternative for cell replacement therapy for Parkinson's disease (PD). To examine in vitro differentiation of hES (MB03, registered in NIH) cells into TH+ cells, hES cells were induced to differentiate according to the 4-/4+ protocol using retinoic acid (RA), ascorbic acid (AA), and/or lithium chloride (LiCl) followed by culture in N2 medium for 14 days, during which time the differentiation occurs. Immunocytochemical stainings of the cells revealed that approximately 21.1% of cells treated with RA plus AA expressed TH protein that is higher than the ratio of TH+ cells seen in any other treatment groups (RA, RA+LiCl or RA+AA+LiCl). In order to see the differentiation pattern in vivo and the ability of in vitro differentiation-induced cells in easing symptomatic motor function of PD animal model, cells (2 10 cells/2) undergone 4-/4+ protocol using RA plus AA without any further treatment were transplanted into unilateral striatum of MPTP-lesioned PD animal model (C57BL/6). Following the surgery, motor behavior of the animals was examined by measuring the retention time on an accelerating rotar-rod far next 10 weeks. No significant differences in retention time of the animals were noticed until 2 weeks post-graft; however, it increased markedly at 6 weeks and 10 weeks time point after the surgery. Immunohistochemical studies confirmed that a reasonable number of TH+ cells were found at the graft site as well as other remote sites, showing the migrating nature of embryonic stem cells. These results suggest that in viかo differentiated hES cells relieve symptomatic motor behavior of PD animal model and should be considered as a promising alternative for the treatment of PD.