최근 지구의 기후변화는 온실가스가 원인으로 전 세계적 대기환경문제로 크게 부각되고 있다. 국내에서도 기후변화에 적극 대응하기 위한 기술개발이 꾸준히 진행되고 있다. 날씨의 이상고온으로 인한 환경에 미치는 영향과 갑작스런 집중호우가 환경에 미치는 영향을 대상으로 하였다. 우리생활 주변 대기온도가 상승하였을 때 온도변화에 의한 대기오염발생에 미치는 영향을 연구하고자 한다. 본 연구의 실험조건은 선박 디젤기관에서 회전수 1400 rpm, 1600 rpm 그리고 1800 rpm, 부하는 0 %에서 25 %씩 100 %까지 하였고, 흡기 온도변화 는 20℃에서 50℃까지 구분하여 연구하였다. 연구한 결과 흡기온도가 증가함에 따라 일산화탄소 및 탄화수소는 약간 감소하였으나 연료 소비율, 질소산화물, PM은 약간 증가하였다. 또한 연소온도는 큰 변화가 없었다.

The fuel used in this study, DMM is an oxygen additive containing 42.5% oxygen by weight and dissolved in diesel fuel, also known as methyl alcohol or Dimethoxymethane (CH3-O-CH2-O-CH3). DMM, which is a colorless liquid, shows chemical characteristics of gas-liquid and is also used as a diesel fuel component. In this study, five mixtures were added to the common diesel fuel at DMM addition rates of 2.5, 5, 7.5, 10 and 12.5% by volume. A single cylinder, four strokes, DI diesel engine was used as the test engine. Experimental data were also collected at 24 engine speed-load conditions operating in steady state. The purpose of this experiment was to study the effect of the addition ratio of oxidized fuel mixed in diesel fuel on engine power and exhaust performance. When compared with the common diesel fuel, the exhaust of Smoke was substantially reduced in all DMM mixing ratios. These results indicate that DMM can be an effective blend of diesel fuel and is an environmentally friendly alternative fuel. This study also shows that smoke and NOx emissions can be reduced at the same time through the application of oxygen fuel and EGR.

The purposes of improving air pollution and suggesting energy resources have intensified research on various alternative energy for diesel combustion engines to solve severe environmental influences caused by air pollution. In this study, the applicable possibility of biodiesel and oxygenates (EGBE) was investigated as a cuspy method on decreasing the smoke emission. The smoke emission of blending fuel (biodiesel and EGBE) was reduced in comparison with commercial diesel fuel and it was reduced almost 63% at 2000 rpm, full load. But torque and brake specific energy fuel consumption rate didn't have any large changes. Also, the effectiveness of exhaust gas recirculation (EGR) for the reduction of NOx emission has been investigated. It was shown that simultaneous reduction of NOx and smoke emission was achieved with biodiesel(90%), oxygenates (10%) and cooled EGR rates (10%) in an IDI diesel engine.

In this paper, we investigate the relationship between fuel injection quantity and voltage and current energy of Bosch system and Delphi system by measuring the high and low voltage waveform, current waveform, fuel injection quantity and fuel pressure of A and J-engines. Waveform measurements are made using the PICO scope and the CDS tester. The injectors of A and J engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. In case of normal injector, A-engine has higher fuel pressure, injection interval time, voltage energy, and current energy than J-engine. The current energy of the A-engine changed linearly compared to that of the J-engine. For over and under injectors, the change in the previous physical quantity was greater for the A-engine than for the J-engine. However, the duration time of maintaining to open the injector is controlled differently, and so the voltage and current energy values are changed, and the change of the current energy is larger than the voltage energy.

본 연구에서는 국내외적으로 환경문제 및 에너지절감의 일환으로 직류배전시스템을 선박에 적용하려는 연구 및 실증이 활발히 수행되고 있으며, 발전기를 직류배전시스템에 적용하기 위해서는 가변속 엔진을 적용하여 저부하 영역에서 발전기의 엔진 회전수를 줄여 연료소모량을 절감할 수 있는 방안이 제시되고 있다. 본 논문에서는 기존의 디젤발전기를 이용하여 발전기 컨트롤러, 가버너, AVR 을 이용하여 직류배전용 가변속발전기를 구성하였으며, 발전기의 시스템 구성 방법, 가변속 발전에 따른 전력품질 시험(전압 및 주파수 변동특성, 부하변동 특성)을 통해 가변속 발전기의 전력특성을 분석 하였다. 가변속 발전기의 전압(250 ~ 440 VAC) 및 주파수(34 ~ 60 Hz)는 정격의 60 ~ 100%로 구성하였으며, 엔진은 1100 ~ 1800 rpm 범위에서 운전되도록 설정 하였다. 부하변동에 따라 발전기의 엔진속도를 변경 시켜서 발전기 출력의 전압, 전류, 주파수가 전력량에 따라 안정적으로 변동되는 것을 확인하였다.

The wavy fins have been widely used in the heat exchangers in coolering system, aerospace system and automotive. Especially, an automobile has the wavy fin and flat tube heat exchanger for oil cooling system. The objective of this research is the performance comparison of wavy fins for battle vehicle diesel engine oil-cooler by numerical analysis. The real type fin is the wavy fin with corrugated structure, and the comparative fin surfaces are plain, louver, lateral perforation and parallel wavy fin. The non-dimensional values of f-factor, j-factor, area goodness factor and volume goodness factor was performed on the performance comparison. The plain and louver fin shows the highest performance in pressure drop and heat transfer respectively. In the area goodness factor and volume goodness factor results, the parallel wavy fin and louver fin show the highest values at each result.

세탄가는 경유의 품질기준 중 하나로써 디젤엔진에 사용되는 경유 연료의 착화성을 평가하는 항목이다. 세탄가 기준은 현재 자동차용 경유 기준으로 52 이상이며, 일반적으로 세탄가가 높으면 시동성이 좋고 운전이 원활해지나 지나치게 높으면 연소가 불균일해져 매연의 원인이 되고 연료소비량이 증가한다. 현재 국내의 품질시험방법에 규정되어있는 세탄가 측정방법은 CFR엔진을 이용한 세탄가분석, 경유의 밀도와 증류유출온도를 통하여 세탄가를 산출하는 세탄지수, CFR엔진의 단점을 보완하여 고온에서 연료의 연소되는 시간을 통해 세탄가를 측정하는 유도세탄가 등이 있다. 본 연구는 이러한 세탄가를 정유사별, 하·동절기별 시료를 확보하고 이를 분석하여 다양한 인자들에 의한 세탄가 측정방법의 상관관계에 대하여 분석하였다. 이를 통하여 세탄가, 유도세탄가, 세탄지수 순으로 세탄가가 높게 측정 되는 것을 확인하였고, 이를 통하여, 현재 편의성을 이유로 많이 사용되는 세탄지수로 인하여 세탄가 품질미달이 발생할 수 있기 때문에 이에 대한 추가 연구가 필요할 것으로 보인다.

This paper investigates the relationship of voltage and current waveform between normal piezo injector and deterioration abnormal piezo injector. The experimental methods using Pico oscilloscope and GDS scan tool are employed to measure current and voltage waveform and fuel pressure of piezo injector. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) In case of normal injector, the fluctuation of duration time of piezo injector was linearly and regularly decreased with increasing engine speed, but the that of deterioration piezo injector was irregularly decreased with increasing engine speed. 2) In main injection, the peak value of the current waveform of abnormal injector was larger than that of normal injector, the duration time of deteriorated abnormal injector was less than that of normal injector at 800rpm and 1500rpm, but the duration time of deteriorated abnormal injector was larger than that of normal injector at 2000rpm and 3000rpm. This irregularity appears to be caused by the deterioration of the injector.