본 연구에서는 지방 산화를 억제하고 품질이 우수한 부세 굴비의 가공법을 개발하기 위해 대두와 멸치의 복합 발효소재를 첨가한 염지제 처리 및 건조 시간에 따른 부세 굴비를 제조하여 품질 특성을 비교하였다. 발효소재 첨가에 따른 염지제와 부세 굴비의 DPPH 및 ABTS 라디칼 소거능은 발효소재의 함량에 따라 증가하였으나, 발효소재 1% 이상에서 부세 굴비의 라디칼 소거능은 유의적인 차이를 보이지 않았다. 발효소재의 함량이 증가할수록 부세 굴비의 아미노태질소 함량은 증가하고 VBN, TBARS, 산가는 감소하는 결과를 나타내나, 발효소재 1% 이상에서 품질의 유의적인 차이가 크지 않으므로 염지제의 발효소재 함량은 1%로 선정하였다. 염지제의 염도에 따른 부세 굴비의 품질을 분석한 결과 염도가 증가할수록 아미노태질소 함량은 증가하고 히스타민, VBN, TBARS, 산가는 감소하는 결과는 나타내며, 염지제의 염도는 품질 개선 효과가 가장 우수한 7% 조건을 선정하였다. 염지 처리 후 건조 시간에 따른 부세 굴비의 품질을 분석한 결 과 건조 시간이 증가할수록 수분은 감소하고 염도, pH, 아미노태질소, 히스타민, VBN, TBARS, 산가는 증가하였다. 그러나 건조 48시간 이하는 수분이 많아 저장성이 낮으며, 건조 96시간에서 히스타민과 산패도의 증가율이 높아지므로 부세 굴비의 건조 시간은 72시간이 적합한 것으 로 판단되었다.

The present study demonstrates the effect of raw powder on the pore structure of porous W-Ni prepared by freeze drying of camphene-based slurries and sintering process. The reduction behavior of WO3 and WO3-NiO powders is analyzed by a temperature programmed reduction method in Ar-10% H2 atmosphere. After heat treatment in hydrogen atmosphere, WO3- NiO powder mixture is completely converted to metallic W without any reaction phases. Camphene slurries with oxide powders are frozen at −30 oC, and pores in the frozen specimens are generated by sublimation of the camphene during drying in air. The green bodies are hydrogen-reduced at 800 oC and sintered at 1000 oC for 1 h. The sintered samples show large and aligned parallel pores to the camphene growth direction, and small pores in the internal wall of large pores. The strut between large pores, prepared from pure WO3 powder, consists of very fine particles with partially necking between the particles. In contrast, the strut densification is clearly observed in the Ni-added W sample due to the enhanced mass transport in activation sintering.

The effect of drying temperature and steaming time on the browning and antioxidant activity of dried Platycodon grandiflorum was investigated. Thirteen treatment conditions were constructed using central composite face-centered design containing 5 center points. Drying temperature and steaming time (as factors) were 45-75oC and 15-45 min. According to treatment conditions, dried Platycodon grandiflorum was assessed for color characteristic, degree of browning, total polyphenol content, and DPPH and ABTS free radical scavenging (as responses). When increasing drying temperature within a given steaming time, dried Platycodon grandiflorum exhibited decreased lightness, increased redness, degree of browning, and total polyphenol contents, and enhanced antioxidant activities. Except for total polyphenol contents and antioxidant activities, steaming time within a given drying temperature exhibited similar effects to those observed in drying temperature. However, steaming time did not likely influence total polyphenol contents and revealed the opposite trends observed for the effect of drying temperature on their antioxidant activities. The overall results suggested that drying temperature was the main factor for changes in the browning and antioxidant activity of dried Platycodon grandiflorum.

Freeze drying of a porous Cu-Sn alloy with unidirectionally aligned pore channels was accomplished by using a composite powder of CuO-SnO2 and camphene. Camphene slurries with CuO-SnO2 content of 3, 5 and 10 vol% were prepared by mixing with a small amount of dispersant at 50˚C. Freezing of a slurry was done at -25˚C while the growth direction of the camphene was unidirectionally controlled. Pores were generated subsequently by sublimation of the camphene during drying in air for 48 h. The green bodies were hydrogen-reduced at 650˚C and then were sintered at 650˚C and 750˚C for 1 h. XRD analysis revealed that the CuO-SnO2 powder was completely converted to Cu-Sn alloy without any reaction phases. The sintered samples showed large pores with an average size of above 100μm which were aligned parallel to the camphene growth direction. Also, the internal walls of the large pores had relatively small pores. The size of the large pores decreased with increasing CuO-SnO2 content due to the change of the degree of powder rearrangement in the slurry. The size of the small pores decreased with increase of the sintering temperature from 650˚C to 750˚C, while that of the large pores was unchanged. These results suggest that a porous alloy body with aligned large pores can be fabricated by a freeze-drying and hydrogen reduction process using oxide powders.

Porous Ti-systems with unidirectionally aligned channels were synthesized by freeze-drying and a heat treatment process. TiH2 powder and camphene were used as the source materials of Ti and sublimable vehicles, respectively. Camphene slurries with TiH2 content of 10 and 15 vol% were prepared by milling at 50˚C with a small amount of oligomeric polyester dispersant. Freezing of the slurry was done in a Teflon cylinder attached to a copper bottom plate cooled at -25˚C while unidirectionally controlling the growth direction of the camphene. Pores were generated subsequently by sublimation of the camphene during drying in air for 48 h. The green body was heat-treated at 1100˚C for 1 h in a nitrogen and air atmosphere. XRD analysis revealed that the samples composed of TiN and TiO2 phase were dependent on the heat-treatment atmosphere. The sintered samples showed large pores of about 120 mm which were aligned parallel to the camphene growth direction. The internal wall of the large pores had relatively small pores with a dendritic structure due to the growth of camphene dendrite depending on the degree of nucleation and powder rearrangement in the slurry. These results suggest that a porous body with an appropriate microstructure can be successfully fabricated by freeze-drying and a controlled sintering process of a camphene/TiH2 slurry.

Ocean discharge of sewage sludge, which started in the year of 1993 in Korea, was stopped in the beginning of 2012, Landfill of sewage sludge was also prohibited in 2003 owing to public acceptance of the lanfill sites, and partially reopened in 2007 due to the necessity of organic component in sludge to produce methane gas. Sludge recycle ratio will increase in sewage sludge treatment by volume reduction and drying, and then recycle of the thermal energy as fuel in power plant and also material as raw material of cement. Several drying processes are compared with reasoning and an appropriate drying sequence is suggested.

목재의 건조 균열방지를 위한 진공흡입기술의 새로운 목재처리방법에 대해 연구를 수행하였다. 목재의 건조균열 방지를 위해 사용된 ployetylene grycogen(PEG) 처리재들은 PEG-1540, PEG-2000, PEG-4000, PEG-10000이었으며, 진공펌프의 감압정도는 85kPa과 39kPa 이었다. 시험결과, 진공흡입처리에 의한 PEG액의 흡입은 방사단면에 걸쳐 고르게 이루워졌음을 확인 할 수 있었다. 또한 PEG의 분자량이 증가할수록 단위시간당 PEG의 분자량이 증가할수록 단위시간당 PEG의 흡입량과 처리전.후의 함수률의 차인δ M.C 는 PEG-2000을 변곡점으로 하여 감소하였다. 그리고 리기다 소나무의 건조균열 방지를 위한 약제 흡입처리에 있어 최적의 PEG 분자량과 농도 그리고 감압력의 조건은 각각 PEG-2000과 30%(wt.)그리고 85kPa임을 알 수 있었다.

Background : Polygonati rhizoma is used for medicine using rhizome of Polygonatum sibiricum Redoute belonging to Liliaceae. This study was carried out to find proper method to establish the guideline of GAP post-harvest management. Methods and Results : Six-years-old polygonati rhizoma harvested in march in Geumsan was used for this study. Steaming was treated for 1, 2, and 3 hours respectively and drying was treated at 45℃, 50℃, 55℃, and 60℃ using hot-air drying machine with checking moisture content at intervals of a day. Moisture contents of polygonati rhizoma according to drying temperature after steaming showed that drying was faster in higher drying temperature treatment after steaming. Moisture content was below 10% as 9.6% and 9.4% at 55℃ drying treatment after steaming for 1 hour and 2 hours respectively. Color value according to treatments was as follows, L-value was lower in longer steaming and higher drying temperature. a-Value was higher in steaming an higher drying temperature. Conclusion : In steaming and hot-air drying treatment to establish the guideline of GAP post-harvest management, moisture content was most proper as 9.4% below 10% in 2-hour steaming and 55℃ hot-air drying for 6 days. L-value was 27.49 and a-value and b-value were 4.38 and 9.73 in this treatment and dried rhizome looked glossy and transparent with higher quality. Proper drying method for polygonati rhizoma was considered as 2-hour steaming and 55℃ hot-air drying for 6 days.

Renewable energy resources from foodwaste have attracted significant interest and, consequently, many alternatives are considered for large-scale biogas treatment processes and small-scale onsite drying processes (heat source: electricity, gas, and dried foodwaste by-product). The pre-treatment process for foodwaste consists of the following sequential steps: collection, transportation, shredding, segregation, and dehydration. After this pre-treatment, the dried foodwaste by-product is recycled into (among others) animal feed, fertilizer/compost or biomass solid fuel. In addition, the leachate?liquid generated by squeezing the foodwaste is used for bio-gasification, achieved through an Anaerobic Digestion (AD) process associated with a sewage co-digestion treatment. In this study, the operation cost and greenhouse gas (GHG) emissions of an improved and simplified small-scale onsite drying treatment are compared with those of a large-scale biogas treatment. The pre-treatment can be improved and simplified via this drying treatment. Through this treatment, operationcost reductions of 45.4%, 50.5%, and 89.6% are achieved when electricity, liquified natural gas (LNG), and biomass solid fuel (dried foodwaste by-product), respectively, are employed as drying heat sources. Furthermore, if the annual amount of foodwaste (5 million ton) is recycled into biomass solid fuel, then significant reductions (7.5 million tCO2-e per annum) in GHG emissions can be realized. Therefore, this study demonstrates that improvement and simplification of the smallscale drying process (i) reduces the operation cost as well as GHG emission levels (to levels lower than those achieved via the large-scale biogas treatment process) and (ii) offers a practical solution for foodwaste treatment and a renewable energy resource.

The objective of this study was to investigate the variation of Chinese milk vetch(Astragalus sinicus L.; CMV) seed quality after flowering. We tagged individual open flowers of CMV at the day of maximum flowering(11 May) in Seoul, Korea. Seed samples were harvested serially at 15, 20, 25 and 30 days after flowering(DAF). To compare with dried seeds, non-dried seeds were tested immediately after harvest and the remaining seeds were placed at room temperature for 4 weeks. Seed length, 1000 seed weight, moisture content, germination rate(GR), mean germination time(MGT), germination speed(GS), germination performance index(GPI) and physical dormancy rate(PDR) were investigated. Seed length increased to 2.6 mm and 1000 seed weight reached up to 2.2 g until 25 DAF. Seed moisture content dramatically decreased from 20 to 25 DAF. Moisture content of non-dried seed(7.5%) was similar to that of dried seed(5.5%) at 25 DAF. The rate of seed viability reached up to 94% at 25 DAF. In case of dried seed, GR increased up to 39% at 25 DAF whereas GR of non-dried seed varied from 5 to 10%. GS and GPI of dried seed were significantly higher than those of non-dried seed since 25 DAF. PDR of dried seed has decreased since 20 DAF, whereas PDR of non-dried seed has increased. GR, GS and GPI increased as PDR decreased. Our results evidenced that PDR might be one of major factor in variation of seed quality, of which development was completed at 25 DAF.

고품질의 지실을 포제하기 위한 건조법을 개발하기 위하여, 미성숙 탱자과실을 자연음건법, 적외선건조법, 동결건조법 등으로 건조하고 분말 및 추출액을 조제하여 이화학적 특성을 조사하였다. 동결건조 분말은 다른 건조법의 분말보다 L값, -a값, carotenoid, chlorophyll a 및 b 함량은 높았으나 naringin 함량은 유의적으로 낮았다. 적외선건조 분말은 자연음건 분말보다 L값, naringin, chlorophyll b 함량은 낮았