As a case study on aspect ratio behavior, Kaolin, zeolite, TiO2, pozzolan and diatomaceous earth minerals are investigated using wet milling with 0.3 pai media. The grinding process using small media of 0.3 pai is suitable for current work processing applications. Primary particles with average particle size distribution D50, ~6 μm are shifted to submicron size, D50 ~0.6 μm, after grinding. Grinding of particles is characterized by various size parameters such as sphericity as geometric shape, equivalent diameter, and average particle size distribution. Herein, we systematically provide an overview of factors affecting the primary particle size reduction. Energy consumption for grinding is determined using classical grinding laws, including Rittinger's and Kick's laws. Submicron size is obtained at maximum frictional shear stress. Alterations in properties of wettability, heat resistance, thermal conductivity, and adhesion increase with increasing particle surface area. In the comparison of the aspect ratio of the submicron powder, the air heat conductivity and the total heat release amount increase 68 % and 2 times, respectively.

Fatigue crack growth retardation of 304 L stainless steel is studied using a neutron diffraction method. Three orthogonal strain components(crack growth, crack opening, and through-thickness direction) are measured in the vicinity of the crack tip along the crack propagation direction. The residual strain profiles (1) at the mid-thickness and (2) at the 1.5 mm away from the mid-thickness of the compact tension(CT) specimen are compared. Residual lattice strains at the 1.5 mm location are slightly higher than at the mid-thickness. The CT specimen is deformed in situ under applied loads, thereby providing evolution of the internal stress fields around the crack tip. A tensile overload results in an increased magnitude of the compressive residual stress field. In the crack growth retardation, it is found that the stresses are dispersed in the crack-wake region, where the highest compressive residual stresses are measured. Our neutron diffraction mapping results reveal that the dominant mechanism is by interrupting the transfer of stress concentration at the crack tip.

PURPOSES : The purpose of this study is to investigate the stresses of the middle slab in a double-deck tunnel owing to the slab lift to replace the underlying elastic pads during maintenance workMETHODS: The middle slab was divided into three different sections: typical section, expansion joint section, and emergency passageway section. Finite element analysis models of these three sections of middle slab were developed, and the stress distribution and maximum stresses were obtained using the models when the middle slab was lifted to replace the underlying elastic pads. Various slab lifting methods were examined in this study such as one-, two-, and multiple-point lifts, distributed lifts, and one or both slab side edge lifts.RESULTS: When the slab side edge is lifted, the longitudinal stresses of the slab are almost the same as the principal stresses. This implies that the governing stresses are the longitudinal stresses. The maximum stresses with both-edge lifts are generally smaller than those with one-edge lifts at all three sections of middle slab.CONCLUSIONS: If the middle slab in a double-deck tunnel is lifted for maintenance, the slab should be lifted at multiple points along the longitudinal direction to reduce the tensile stresses.

Numerical analysis has been performed to investigate the stress distribution characteristics of auxiliary axle system in a compact special vehicle. Structural and running stability of compact special vehicle is largely affected by auxiliary axle system installation. Structural characteristics of stress and deformation distributions with safe factor in the auxiliary axle system are analyzed. It can be seen that maximum stress happens near the local axle position, and deformation is also predicted. Simulation results are also compared with experimental test data. These results from this study could be applicable for optimal design of diverse axle systems in the compact special vehicle.

상태 기반 페리다이나믹 모델은 일반적인 재료 구성 모델을 구현할 수 있고 비국부 영역 내에서 연결된 모든 결합의 변형을 통해 각 절점의 재료 응답이 결정되기 때문에 체적 및 전단 변형을 모두 표현할 수 있다. 따라서 상태 기반 모델은 복잡한 동적 취성 파괴 현상(분기균열, 2차 균열, 계단균열, 균열 유착 등)을 해석하는데 유용하다. 본 논문에서는 평면응력 탄성체에 대해 2차원 상태 기반 페리다이나믹 모델을 적용하고 에너지해방율과 페리다이나믹 에너지 포텐셜로부터 손상 모델을 구성하였다. 페리다이나믹 파괴 해석 모델을 통해 취성 유리 재료에 대해 균열 면에 평행한 압축 응력파가 균열 분기 패턴에 미치는 영향에 대해 조사하였다. 실험을 통해 관찰된 동적 균열 진전 및 분기 패턴에 대한 주요 특성들이 페리다이나믹 해석을 통해 확인되었다. 또한 강한 인장 하중 하의 계단균열과 이차균열 등이 상태 기반 페리다이나믹 시뮬레이션을 통해 잘 모사가 되는 것을 확인할 수 있었다.

A kart is a vehicle without the suspension system and the differential gear. The kart frame as an elastic body plays the role of a spring. By the cornering of a kart, rolling, pitching and twisting motions are induced in the kart frame. Also the slip or noncontact of the wheel and a permanent deformation of the kart frame can be induced. In order to examine closely this phenomenon of the twisting deformation, measurement and analysis on torsion working stress with strain gage and tracking system are needed. According to the measurement result, while steady state driving in a curve in general the torsion working stress of the kart frame will be increased depending on the vehicle velocity, but the kart frame will be not permanent deformed. However, analysis of the torsion working stress in comparison with torsion fatigue limit shows that while unsteady state driving as clash with same drive condition the racing kart frame will be deformed more quickly as the leisure kart frame.

본 논문에서는 신뢰적인 PSC 교량 내하성능 평가 기법 제안을 위해 PSC 교량 해석 모델을 이용한 구조물의 거동 양상을 분석하고 교량의 실제 변형률 데이터를 반영한 교량의 거더별 긴장력 손실량 유추 및 활용을 위해 PS 텐던의 긴장력 손실에 따른 교량의 응력 이완 패턴을 도출한다. 그리고 실제 교량의 계측 변형률에 큰 비중을 차지하는 온도구 배의 영향을 적절하게 제거해 긴장력에 의한 변형률 데이터를 추출한다.

The stresses occurred in the middle slab at the areas of the emergency passageway in a double-deck tunnel are analyzed when the slab is lifted to replace bearing pads placed between the middle slab and supporting bracket as a maintenance process. The middle slab can be lifted at several different points near the emergency passageway areas and the stresses of the middle slab depend on the lifting points. This study presents the effect of the lifting location of the middle slab on the stress occurrence for the maintenance work of replacing bearing pads under the middle slab near the emergency passageway areas.

This study is the measurement for fatigue cracks at U-Rib in the steel deck bridge. Thus, to analyze the causes and reinforcement methods through the measurement results. So the bridge will preserve the safety & usability and want to enhance the durability.

Data from the strain gauge and temperature sensor through the analysis in the future appear to be capable of vertical construction step analysis Behavior of Concrete Box Girder is judged to be high usability.

최근 기능성 나노물질로서 반도체 공정 중 기계.화학적 평탄화(CMP)용 연마제로 중요하게 사용되는 세리아(Ceria, CeO2)에 대해서 X-선 회절분석을 실시하여 리트벨트법에 의한 상세한 구조해석 및 세리아의 입자크기와 미세응력을 측정하였다. 두 시료(RT735. RT835)의 리트벨트 계산 결과 R지수 값은 각각 Rp(%)=8.50, 8.34; Rwp(%)=13.4, 13.5; Rexp(%)=11.3, 11.5; RB(%)=2.21, 2.36; S(GofF: Goodness of fit)=1.2, 1.2를 보여주며 계산이 잘 이루어졌음을 알 수 있다. CeO2는 공간군 Fm3m을 가지며, 격자상수는 a=5.41074(2), 5.41130(6) a, V=158.406(1), 158.455(3) a3으로 각각 계산되었다. 입자크기 및 미세응력 계산 결과, RT735의 평균 입자크기와 최대 응력은 37.42(1) nm, 0.0026이며, RT835는 72.80(2) nm, 0.0013으로 각각 결정되었다. 입자크기와 미세응력은 서로 반비례함을 알 수 있다.