ASCE 4 requires that a hard stop be built around the seismic isolation system in nuclear power plants. In order to maintain the function of the isolation system, this hard stop is required to have clearance-to-stop, which should be no less than the 90th-percentile displacements for 150% Design Basis Earthquake (DBE) shaking. Huang et al. calculated clearance-to-stop by using a Latin Hypercube Sampling technique, without considering the rocking behavior of the isolated structure. This paper investigates the effects on estimation of clearance-to-stop due to 1) rocking behavior of the isolated structure and 2) sampling technique for considering the uncertainties of isolation system. This paper explains the simplified analysis model to consider the rocking behavior of the isolated structure, and the input earthquakes recorded at Diablo Canyon in the western United States. In order to more accurately approximate the distribution tail of the horizontal displacement in the isolated structure, a modified Latin Hypercube Sampling technique is proposed, and then this technique was applied to consider the uncertainty of the isolation system. Through the use of this technique, it was found that rocking behavior has no significant effect on horizontal displacement (and thus clearance-to-stop) of the isolated structure, and the modified Latin Hypercube Sampling technique more accurately approximates the distribution tail of the horizontal displacement than the existing Latin Hypercube Sampling technique.

Seismic isolation has been considered and utilized in various industries as a way to prevent huge damage on to structures by large earthquakes in various industries. The laminated Laminated rubber bearings is are most frequently used in seismic isolation systems. The structural Structural safety could not be assured unless the performance of the rubber bearing is not guaranteed for the life time of the structure under the consideration that the bearing is a critical structural member to sustain vertical loads in the seismically isolated structure. However, there are few studies on the deterioration problems of rubber bearings during their service life. The long term performance of the rubber bearings was not considered in past designs of seismically isolated structures. This study evaluates the long term performance and creep characteristics of laminated natural rubber bearings that are used in seismically isolated buildings. For the this study, a set of accelerated thermal aging tests and creep tests are were performed on real specimens. The experimental results show that the natural rubber bearings would have a stable change rate of change for durability under severe environmental conditions for a long time.

Steel plate concrete (SC) composite structure is now being recognized as a promising technology applicable to nuclear power plants as it is faster and suitable for modular construction. It is required to identify its dynamic characteristics prior to perform the seismic design of the SC structure. Particularly, the damping ratio of the structure is one of the critical design factors to control the dynamic response of structure. This paper compares the criteria for the damping ratios of each type of structures which are prescribed in the regulatory guide for the nuclear power plant. In order to identify the damping ratio of SC shear wall, this study made SC wall specimens and conducted experiments by cyclic lateral load tests and vibration tests with impact hammer. During the lateral loading test, SC wall specimens exhibited large ductile capacities with increasing amplitude of loading due to the confinement effects by the steel plate and the damping ratios increased until failure. The experimental results show that the damping ratios increased from about 6% to about 20% by increasing the load from the safe shutdown earthquake level to the ultimate strength level.

최근 국내에서는 원자력발전소의 모듈화 공법에 적용하기 위하여 SC(steel plate concrete) 구조를 개발하는 연구를 진행하고 있다. 이 연구에서는 전단보강이 없는 비보강 SC 전단벽의 횡방향 내진성능 및 강성특성에 대하여 분석하기 위하여 전단벽 모형시편을 제작하고, 이를 대상으로 정적가력실험을 수행하였다. 실험 결과를 이용하여, 이 논문에서는 비보강 SC 구조의 횡력에 대한 파괴모드의 유형을 분석하고, 단면강도와 부재의 강성 특성을 검토하였다. 그리고 SC 구조용 설계기준에서 제시하는 단면의 강도 계산식과실험결과를 비교하였다. 연구결과, 비보강 SC 전단벽의 파괴 형태의 하나는 콘크리트와 강판의 부착 상실로 인한 휨전단파괴라는 사실을발견하였다. SC 구조 전단벽의 벽체 길이방향 거동은 파괴 시까지 벽체 외측의 강판이 내부 콘크리트를 구속하는 효과를 기대할 수 있으므로 연성능력이 향상되는 것이 확인되었다

In this present study to investigate the seismic response of an offshore wind turbine, incorporating with bottom fixed Jacket support structure using semi-coupled analysis method. Fully coupled, aero-servo-hydro-elastic simulations and uncoupled seismic simulation have been done to carry out this investigation. The fully coupled simulation is accomplished and executed by FAST 8 (NREL, USA) to determine the global loads, which consists of six components of forces and moments at x-y-z directions of the tower base. In the uncoupled case, transient analysis has been done using the tower base loads as well as seismic loads by ANSYS. This paper presents a precise dynamic analysis, which can evaluate the dynamic response of three crucial points (tower top, tower base and mud line of substructure) under seismic load to make better decision in the case of structural design of wind turbine.

This study reviewed analytically the behavior of Steel Plate Concrete(SC) walls subjected to shear forces to investigate the effects of shape and arrangement spacing of studs on the design of SC walls. The results showed that the steel plate was yielded at the lower load than the second yielding shear force of the design skeleton curve when the spacing of stud is excessively far from each other. It is also found that the shape of the stud did not affect the shear behavior of SC wall, however, the spacing influenced to its composite action.

This study reviewed analytically the behavior of Steel Plate Concrete(SC) walls subjected to axial forces to investigate the effects of shape and arrangement spacing of studs on the design of SC walls. In this study, it was proven that the inclined shaped stud resists more effectively to the bucking load than the general shaped stud in SC wall.

역량스펙트럼방법은 구조물의 내진성능을 평가하는 도구로서 점점 더 이용 빈도가 증가하고 있다. 강도감소계수는 역량스펙트럼방법에서 정의하는 비탄성요구스펙트럼을 생성하기 위해 사용되며 다양한 강도감소계수 공식들이 제안되고 있다. 이 연구는 강도감소계수의 공식이 비탄성요구스펙트럼의 형상에 미치는 영향과 아울러 교량의 지진응답변위에 미치는 영향을 평가하였다. 연구 목적에 따라, 기존에 제안된 몇 가지 강도감소계수 공식들이 조사되고, 예제연구를 통하여 분석되었다. 서로 다른 원호각을 갖는 곡선교를 선정하여 서로 다른 강도감소계수 공식을 적용하여 역량스펙트럼방법으로 교각의 변위를 평가하였다. 역량스펙트럼의 결과를 검증할 목적으로 비선형시간이력해석도 함께 수행되었다. 연구결과에 의하면, 역량스펙트럼방법은 더 큰 원호각을 갖는 교량일수록 실제보다 더 큰 교각의 변위를 산출한다. 비탄성요구스펙트럼을 작성하는 많은 방법이 제안되어 있음에도 불구하고, 각 방법들이 산출하는 교각의 비탄성변위응답은 큰 차이가 없다.