From the results of model tests, statistical regression analysis for EHP estimation based on hull form parameters is adopted in this study. From this result, the method for estimation of EHP and optimization of hull form parameters at the initial design stage of fishing boats is developed. This method is applied to two standard fishing boats with chine lines. The EHP s are estimated and compared to experimental results. From the optimization of four principal hull form parameters of these fishing boats, approximately 19% of resistance reduction at the design speed is achieved and thus certifies that this method can be used efficiently for the initial design of hull forms of fishing boats.

On the slamming analysis of ship design the data for the impact pressure acted on the forward bottom of a ship are needed. Furthermore impact pressure is given by the function of both the hull form coefficient and relative velocity. In this papper. a simplified method to estimate hull form coefficient by perso;,al computer (p. c.) is studied. This numerical analysis was applied to the model of the Mariner type. and then the result by the p. c. was compared with that by IBM 7090 computer. Main results obtained are as follows: 1. The result by the developed p. c. method had fairly good agreement with that by conventional large computer (IBM 7090) within 2% error. 2. This developed method' by p. c. may be applied to the initial estimation of the K-value because of the close agreement between the ship lines by the results of p. c. and that of input.

최적화기법과 선형변환 자동화기법을 도입하여 고속 중형 Ro-Pax선박의 조파저항성능을 향상시킬 수 있는 선형설계방법에 대하여 연구하였다. 최적화기법으로는 SQP(sequential quadratic programming)을 적용하였으며, 선형변환 자동화기법으로는 NURBS(Non-Uniform Rational B-Spline)기법을 적용하였다. 목적함수인 선박의 조파저항성능을 예측하기 위하여 비선형 자유수면 경계조건과 선체의 침하량을 고려한 비점성 유동 해석 기법인 패널법을 적용하였다. 기준선형에 대하여 선형최적화를 수행하였으며 그 결과로 도출된 최적선형에 대하여 모형선을 제작하여 모형시험을 수행하였다. 기준선형과 최적선형에 대한 수치해석을 수행하여 얻은 결과와 최적선형에 대한 모형시험을 수행하여 얻은 결과를 서로 비교하였다.

본 연구에서는 최적화기법과 전산유체역학의 기술을 이용하여 저항의 관점에서 최적의 형상을 가지는 선형을 개발하는 알고리즘을 개발하였다. 최적화기법으로는 SQP(sequential quadratic programming)을 사용하였으며, 목적함수인 저항을 구하기 위하여 먼저 조파저항은 비선형 자유수면 경계조건을 고려한 선체주위 포텐셜유동을 계산할 수 있는 수치해석기법인 상 방향 패널이동법을 사용하였고, 선체에 미치는 전 저항을 구하기 위하여 ITTC 1957년 모형선-실선상관곡선을 이용하였다. 선형최적화 과정 중의 선체의 변경이나 계산 격자의 생성은 NURBS(Non-Uniform Rational B-Spline)기법을 사용하여 구현하였다. 이와 같은 방법을 사용하여 개발된 선형최적화 기법의 타당성을 검증하기 위하여 선형이 비교적 잘 알려진 건형인 Wigley선형과 Series 60(CB=0.6)선형에 대하여 설계속도 Fn=0.316에서 선형최적화를 위한 수치해석을 수행하고 그 결과를 초기선형과 서로 비교하였다.

This paper presents the method for developing an optimum hull form with minimum wave resistance using SQP( sequential quadratic programming) as an optimization technique. The wave resistance is evaluated by a Rankine source panel method with non-linear free surface conditions and the ITTC 1957 friction line is used to predict the frictional resistance coefficient. The geometry of the hull surface is represented and modified using NURBS(Non-Uniform Rational B-Spline) surface patches. To verify the validity of the developed program the numerical calculations for Wigley hull and Series 60 Cb=0.6 hull are performed and the results obtained after the numerical calculations are compared with the initial hulls.

In this paper, important parameters of fast catamaran hull form are investigated. Praticularly, length-displacement ratio, demihull spacing, trim and hull form on resistance performance are analyzed. Also, the usefulness of SHIPFLOW program for hull form development is studied. The computed results by using SHIPFLOW program are compared with experimental results in model test.