In this study, the effects of Sm addition (0, 0.05, 0.2, 0.5 wt%) on the microstructure, hardness, and electrical and thermal conductivity of Al-11Si-1.5Cu aluminum alloy were investigated. As a result of Sm addition, increment in the amount of α-Al and refinement of primary Si from 70 to 10 μm were observed due to eutectic temperature depression. On the other hand, Sm was less effective at refining eutectic Si because of insufficient addition. The phase analysis results indicated that Sm-rich intermetallic phases such as Al-Fe-Mg-Si and Al-Si-Cu formed and led to decrements in the amount of primary Si and eutectic Si. These microstructure changes affected not only the hardness but also the electrical and thermal conductivity. When 0.5 wt% Sm was added to the alloy, hardness increased from 84.4 to 91.3 Hv, and electric conductivity increased from 15.14 to 16.97 MS/m. Thermal conductivity greatly increased from 133 to 157 W/m·K.

To meet the current demand in the fields of permanent magnets for achieving a high energy density, it is imperative to prepare nano-to-microscale rare-earth-based magnets with well-defined microstructures, controlled homogeneity, and magnetic characteristics via a bottom-up approach. Here, on the basis of a microstructural study and qualitative magnetic measurements, optimized reduction conditions for the preparation of nanostructured Sm-Co magnets are proposed, and the elucidation of the reduction-diffusion behavior in the binary phase system is clearly manifested. In addition, we have investigated the microstructural, crystallographic, and magnetic properties of the Sm-Co magnets prepared under different reduction conditions, that is, H2 gas, calcium, and calcium hydride. This work provides a potential approach to prepare high-quality Sm-Co-based nanofibers, and moreover, it can be extended to the experimental design of other magnetic alloys.

LiCl-KCl 용융염에서 광학적으로 투명한 텅스텐 망으로 제작된 작업전극에 대해 사마륨의 전기화학적 거동을 Cyclic voltammetry와 Potential step chronoabsorptometry의 전기화학적 및 분광전기화학적 방법으로 조사하였다. Cyclic voltammogram 으로 결정된 Sm3+/Sm2+의 산화환원 반응의 가역성을 기반으로 형식전위와 확산계수를 계산하여 각각 –1.99 V vs. Cl2/Cl- 와 2.53×10-6 cm2·s-1를 얻었다. 작업 전극에 –1.5 V vs. Ag/AgCl (wt%)로 전압을 인가하여 측정한 Chronoabsorptometry 를 통해 사마륨 이온의 특성 파장으로 Sm3+에 대해 408.08 nm, Sm2+에 대해 545.62 nm를 확인하였다. Voltammogram에서 얻은 환원 피크 전압과 산화 피크 전압을 이용하여 Potential step chronoabsorptometry를 수행하였다. 545.63 nm의 흡광 피크 값을 분석하여 2.15×10-6 cm2·s-1의 확산계수를 얻었으며 이 값은 동일한 온도에서 Cyclic voltammtry 분석으로 얻은 값과 큰 차이를 보이지 않았다. 실험결과로부터 고온 용융염에서 광학적으로 투명한 작업전극을 이용한 분광전기화학적 방 법이 용융염에 용해된 이온의 종류를 확인하며 전기화학적 거동을 조사하는데 유용한 도구로 활용될 수 있음을 확인하였다.

To produce alloy powders with only SmFe single phase by reduction-diffusion (R-D) method, the effect of excess samarium oxide on the preparation of Sm-Fe alloy powder during R-D heat treatment was studied. The quantity of samarium oxide was varied from 5% to 50% whereas iron and calcium were taken 0% and 200% in excess of chemical equivalent, respectively. The pellet type mixture of samarium, iron powders and calcium granulars was subjected to heat treatment at 1100 for 5 hours. The R-D treated pellet was moved into deionized water and agitated to separate Sm-Fe alloy powders. After washing them in deionized water several times, the powders were washed with acetic acid to remove the undesired reaction products such as CaO. By these washing and acid cleaning treatment, only 0.03 wt% calcium remained in Sm-Fe alloy powders. It was also confirmed that the content of unreacted -Fe in SmFe matrix gradually decreased as the percentage of samarium oxide is increased. However, there was no significant change above 40% excess samarium oxide.