In this study, a river basin with a lot of measured data such as water level, flow rate, current speed, and sediment rate from the past to now was selected and geometrical shape of a pier was re-analyzed, in order to study the effects of the flow around the pier area as well as the riverbed alternation characteristics. A finite element mesh of the entire river was prepared, and via parameter revision, the section that the pier has influence on was decided, to analyze the shape of the pier using RMA-2 and SED2D-WES models. With regards to the section that the pier has influence on, analysis was done on the four pier shapes, namely circle, square, rectangle, and octagon. The results showed that the shape with the least influence around the pier around is the octagon, followed by circle, rectangle, and square, showing the different geometrical effects that the shapes have on the pier. Furthermore, it was shown that the distribution of sediment concentration had effect from about (+)110 m of the upstream to about (-)130 m of the downstream, from the pier installation point. Also, it was shown after analyzing drag forces for different sediment particle distributions that the shape with the greatest drag is the octagon, followed by circle, square, and rectangle.

This study intends to estimate the best model parameters for predicting the water quality and discharge of the study area, and provide the basic data necessary for predicting the water quality and discharge and examining changes in water quality on the basis of the changes hydraulic and hydrological changes and pollutional load of the study area. Nakdong River was selected for analysis, and the water quality survey data necessary for parameter estimation was based on the monthly water quality data (discharge, BOD, T-N and T-P) between December 1, 2002 ~ November 31, 2002. The topographical characteristics factors of the study area were based on the 1/25,000 numerical map published by the National Geographic Information Institute and satellite photographs. The presumed course: It measured the most suitable parameter that could imitate surveyed water quality and discharge using the method of trial and error, in this part the first numerical value was the model parameter presented SWAT. The result of analisys showed that a relative error between surveyed value and the result of water quality imitation about BOD, T-N, T-P that examined by this study, discharge correction : R2=0.912, discharge verification : R2=0.838, correction and verification of BOD : R2=0.847, correction and verification of T-N : R2=0.712 and, correction and verification of T-P : R2=0.726 and, BOD : RK1, RK3, T-N : RS3, RS4, T-P : RS2, RS5, GWSOLP, discharge : ALPAHA_BF, GWQMN, CH_N(2), CN2, SOL_AWC have been considered as the factors of the water quality performed in this water quality simulation, that is, the most effective parameters on BOD, T-N and T-P. It is considered that it will be possible to apply the most optimal parameter to an analysis of the water quality and discharge simulation at study area in the goal year by examining the interaction of the parameters through the parameters sampling which are able to applicable to prediction of the water quality and discharge in the future, also the analysis on the basis of the hydrological conditions: an outflow or the character of a flow will be needed.

The purpose of this study is to analyze the sensitivity of the RMA2 model parameters reflecting the flow characteristics of stream junction and thus understand the hydraulic characteristics of the channel confluence flow. This study dealt with the input parameters of the RMA-2 model, a two-dimensional numerical analysis model widely used for researches both at home and abroad. The parameters of the RMA-2 model are roughness coefficient, turbulent diffusion coefficient, Coriolis forces latitude, Density, and mesh size. This study those parameters estimated from actual heavy rainfall, and varied the parameter size by (-)30%～+30% to review the characteristics of the flow characteristics of the channel section. Weobserved that when the ratio of the channel width was relatively small, the smaller the approaching angle was, the farther from the junctions became the generating place of the maximum flow velocity, however, when the ratio of the channel width was relatively large, the larger the approaching angle was, the farther the generating place of the maximum flow velocity from the junctions became. In particular, the distance between junctions and the place where the maximum flow velocity generated showed an absolute correlationover 90% of the relative channel width, but an inverse relationwas found when the distance to the place where the flow velocity generated was shortened as relative the channel width between the main channel and tributary increased.

This study intends to provide the necessary basic data needed for predicting the water quality and examining changes in water quality on the basis of the hydrological changes: an outflow or the character of a flow by investigating the interaction of the parameters through the estimation of optimal parameters need for predicting the water quality of the dam basin and the sensitivity among those estimated parameters. Im-Ha Dam in the upstream area of the Nakdong River was selected for analysis, and the water quality survey data necessary for parameter estimation was based on the monthly water quality data (water temperature, BOD, T-N and T-P) between December 1, 2005~November 31, 2006. K1C(the saturated growth rate of plant plankton), K1RC (endogenous respiratory quotient of plankton), KDC(deoxidized ratio), K71C(minealized ratio of dissolved organic phosphorus), K83C(mineralized ratio of dissolved organic nitrogen) have been considered as the factors of the water quality performed in this water quality simulation, that is, the most effective parameters on BOD, T-N and T-P. In the result of the analysis of the sensitivity, KDC(deoxidized ratio) was the most sensitively reacted parameter on BOD and it was K71C(mineralized ratio of dissolved organic phosphorus) and K83C(mineralized ratio of dissolved organic nitrogen) on T-N and T-P. It is considered that it will be possible to apply the most optimal parameter to an analysis of the water quality simulation at Im-Ha Ho basin in the goal year by examining the interaction of the parameters through the parameters sampling which are able to applicable to prediction of the water quality and the analysis of the its sensitivity, in the future, also the analysis on the basis of the hydrological conditions: an outflow or the character of a flow will be needed.

The objective of this study is analysis of Andong-Dam lake water quality with water quality model. Model parameters of the WASP applied to Lake Andong-Dam were estimated. The methodology is based on grouping water quality constituents and relevant parameters and successively estimating parameters by a trial-and-error procedure. Water quality system for modeling consisted of BOD, DO, T-N, T-P. The results of water quality modelling using WASP. T-N was maximum affected by K71C(Organic nitrogen mineralization rate) parameter. T-P was maximum affected by K83C(Dissolved organic phosphorus mineralization) parameter, and It did not show a difference almost from the parameter of others and it omitted. BOD was maximum affected by Temperature parameter, it was visible of the reaction due to the KDC(Deoxygenation rate) in afterwords, and It did not show a difference from the parameter of others and it omitted. DO was maximum affect by Temperature parameter, and It did not show a difference almost from the parameter of others and it omitted. The parameter which it presumes from the this study uses a water quality modeling and Actual value and the result with which it compares, error rate the parameter presumption which is appropriate with 1% interior and exterior is investigated, It will reach and it uses and it will be able to apply to the suitable parameter in water quality modelling of the objective area which can be feeded by it becomes.