Due to the necessity of isolating spent nuclear fuel (SNF) from the human life zone for a minimum of 106 years, deep geological disposal (DGD) has emerged as a prominent solution for SNF management in numerous countries. Consequently, the resilience of disposal canisters to corrosion over such an extended storage period becomes paramount. While copper exhibits a relatively low corrosion rate, typically measured in millimeters per million years, in geological environment, special attention must be directed towards verifying the corrosion resistance of copper canister welds. This validation becomes inevitable during the sealing of the disposal canister once SNFs are loaded, primarily because the weld zone presents a discontinuous microstructure, which can accelerate both uniform and localized corrosion processes. In this research, we conducted an in-depth analysis of the microstructural characteristics of copper welds manufactured by TIG-based wire are additive manufacturing, which is ideal for welding relatively large structures such as a disposal canister. To simulate the welds of copper canister, a 12 mm thick oxygen-free plate was prepared and Y and V grooves were applied to perform overlay welding. Both copper welding zones were very uniform, with negligible defects (i.e., void and cracks), and contained relatively large grains with columnar structure regardless of groove types. For improving microstructures at welds with better corrosion resistance, the effect of preheat temperature also investigated up to 600°C.

Since spent nuclear fuel (SNF) should be isolated from the human life zone for at least 106 years, deep geological disposal (DGD) is considered a strong candidate for SNF management in many countries. Therefore, a disposal canister should be nearly immune to corrosion in such a long-term storage environment. Even though copper has a low corrosion rate of a few millimeters per million years in geological environments, the corrosion resistance of the copper welds must be preferentially validated, which inevitably occurs during the sealing of the disposal canister after the SNF is loaded. This is because the weld zone is a discontinuous area of microstructure, which can accelerate uniform and localized corrosion. In this study, the microstructural characteristics of copper welds in different welding conditions such as friction stir welding, electron beam welding, cold spray, were analyzed, focusing on the formation of microstructure, which affects resistance to corrosion. In addition, the microstructure and corrosion properties of the copper weld zone manufactured by recent wire-based additive manufacturing (AM) technology were experimentally evaluated. From this preliminary test result, it was found that the corrosion characteristics of the welds produced by the AM process using wire are comparable to those of the conventional forged copper plate.

A diverse group of plant-growth promoting bacteria were isolated in button mushroom (Agaricus bisporus) media to investigate the plant-growth promoting traits of compounds including indole acetic acid (IAA), ammonia, 1-aminocyclopropane-1- carboxylic acid deaminase, siderophore, and hydrogen cyanide. Twenty-one bacterial strains showing positive effects for all the test traits were selected and classified to confirm bacterial diversity in the media habitat. Plant-growth promoting traits of the isolates were also assessed. All strains produced IAA ranging from 20 μg/mL to 250 μg/mL. Most of the isolates produced more than 80% siderophore. Four strains (Pantoea sp., PSB-08, Bacillus sp., PSB-13, Pseudomonas sp., PSB-17, and Enterobacter sp., PSB-21) showed outstanding performances for all the tested traits. In a bioassay of these four strains using mung bean plant, the best growth performances (23.16 cm, 22.98 cm, 2.27 g/plant, and 1.83 g/plant for shoot length, root length, shoot dry weight, and root dry weight, respectively) were obtained from the plants co-inoculated with Bacillus sp., PSB-13. The resultant data indicate that button mushroom media have got a diverse group of bacteria with plant growth promoting abilities. Thus, the media could be a good recycling resource for using to an effective bio-fertilizer.

The goal of this study was to evaluate effects of various microbial and organic additives on chemical compositions, fermentation indices, and aerobic stability of barley silage. Youngyang barley harvested at 31.5% dry matter (DM), and ensiled into 20 L bucket silo for 0, 1, 3, 7, 48, and 100 d in quadruplicates with four additives following: sterile destilled water at 1% of fresh forage (CON); Lactobacillus plantarum at 1.2 x 105 cfu/g of fresh forage (CL); Lactobacillus buchneri at rate of 1.2 x 105 cfu/g fresh forage (LB); Fermented Persimmon Extract at 1% of fresh forage (FPE); and Essential Oil at 1% of fresh forage (EO). On 100 d of ensiling, CL and FPE silages had lower (p<0.05) DM than CON silage. Additionally, FPE silage had higher (p<0.05) crude protein than CON silage. All silages with additives, except EO, had higher (p<0.05) neutral detergent fiber (NDF) than CON silage. Silage treated with CL, LB, and FPE had lower in vitro DM digestibility than CON silage, and silages treated with LB and FPE had higher in vitro NDF digestibility (IVNDFD) on 100 d of ensiling. The PFE silage produced the highest (p<0.05) lactate during ensiling period, while LB silage produced the highest (p<0.05) acetate. All inoculated silages had higher (p<0.05) LAB count than control silage. Only CL silage had higher (p<0.05) yeast count than control silage, while the other silages were not differ compared to CON silage. The aerobic stability was higher (p<0.05) in LB and FPE silages than in CON silage. In conclusion, FPE could be an alternative additive to increase IVNDFD, fermentation indices, and aerobic stability of barley silage.

We focus on the weapon target assignment and fire scheduling problem (WTAFSP) with the objective of minimizing the makespan, i.e., the latest completion time of a given set of firing operations. In this study, we assume that there are m available weapons to fire at n targets (> m). The artillery attack operation consists of two steps of sequential procedure : assignment of weapons to the targets; and scheduling firing operations against the targets that are assigned to each weapon. This problem is a combination of weapon target assignment problem (WTAP) and fire scheduling problem (FSP). To solve this problem, we define the problem with a mixed integer programming model. Then, we develop exact algorithms based on a dynamic programming technique. Also, we suggest how to find lower bounds and upper bounds to a given problem. To evaluate the performance of developed exact algorithms, computational experiments are performed on randomly generated problems. From the results, we can see suggested exact algorithm solves problems of a medium size within a reasonable amount of computation time. Also, the results show that the computation time required for suggested exact algorithm can be seen to increase rapidly as the problem size grows. We report the result with analysis and give directions for future research for this study. This study is meaningful in that it suggests an exact algorithm for a more realistic problem than existing researches. Also, this study can provide a basis for developing algorithms that can solve larger size problems.

We focus on the fire scheduling problem (FSP), the problem of determining the sequence of targets to be fired at, for the objective of minimizing makespan to achieve tactical goals. In this paper, we assume that there are m available weapons to fire at n targets (> m) and the weapons are already allocated to targets. One weapon or multiple weapons can fire at one target and these fire operations should start simultaneously while the finish time of them may be different. We develop several dominance properties and a lower bound for the problem, and suggest a branch and bound algorithm implementing them. Also, In addition, heuristic algorithms that can be used for obtaining an initial upper bound in the B&B algorithm and for obtaining good solutions in a short time were developed. Computational experiments are performed on randomly generated test problems and results show that the suggested algorithm solves problems of a medium size in a reasonable amount of computation time. The proposed lower bound, the dominance properties, and the heuristics for upper bound are tested in B&B respectively, and the result showed that lower bound is effective to fathoming nodes and the dominance properties and heuristics also worked well. Also, it is showed that the CPU time required by this algorithm increases rapidly as the problem size increases. Therefore, the suggested B&B algorithm would be limited to solve large size problems. However, the employed heuristic algorithms can be effectively used in the B&B algorithm and can give good solutions for large problems within a few seconds.

Type I clathrate was produced by arc melting and hot pressing and thermoelectric properties were investigated. Negative Seebeck coefficient at all temperatures measured, which means that the majority carriers are electrons. Electrical conductivity decreased by increasing temperature and thermal conductivity was 0.012 W/cmK at room temperature and dimensionless thermoelectric figure of merit (ZT) was 0.01 at 873K.

The Powder characteristics and sintering behavior of coated were studied. Silica coated powders were prepared by sol-gel method. The particle size of the powders were nm and the thickness of the coating layer was nm. As the content increased, the layers improved the powder dispersion. The Zeta potential of coated was getting close to that of pure silica with a more negative charge, compared with that of the uncoated . The onset temperature of shrinkage curves shifted to higher temperatures with increasing contents

When was added to Ti-excess ((Ba+Y)/Ti =1), the area occupied by ion was confirmed by its microstructure development, electrical conductivity behavior and lattice constant. Grain growth inhibition was observed when the content of donor dopant exceeded a critical value () in system. A donor-doped behavior was observed at various Y contents ( mol% Y) when was added to -excess . As Y content was increased, (002) and (200) peaks shifted to higher angles and the lattice constant (a and c axis) decreased gradually.

원전 작업자 방사선량의 효과적인 저감을 위해서는 발전소 내에 축적된 작업자 피폭선량자료들을 분석하는 것이 반드시 필요하다. 자료의 분석을 통해, 발전소에서 수행되는 방사선작업들 중 반복적으로 고피폭을 유발하는 작업들을 파악하는 것이 필요하며, 본 연구에서는 이러한 반복성고피폭작업들을 도출하기 위한 방법론으로 백분위수 순위합 방법을 제안한다. 이는 비모수통계학 이론에 근거한 방법론으로, 본 연구에서는 이 방법을 이용하여 고리 3,4 호기 작업자 피폭선량 자료를 분석, 고피폭작업들을 도출하였다. 도출 결과는 통계적으로 검증되며, 그 결과 백분위수 순위합 방법의 효과 및 타당성을 입증하였다.