This paper describes the influence of recycled materials on the flowability of steel fiber-reinforced cement composites. For the FRCC, fly-ash and recycled sand were used as recycled materials. The recycled materials were mixed with replacement ratios of 25% and 50%. As reinforcing fiber for the FRCC, micro steel fibers were used. Based on the test results, flowability of FRCC was improved when fly-ash was replaced. Increase of recycled sand had FRCCs exhibited lower flowability.

Thin plate amorphous steel fiber has more tensile strength and corrosion resistance than general steel fiber, and it has different fiber direction by casting direction. In this study, evaluating impact resistance and sectional crack characteristic of amorphous steel fiber-reinforced cement composites by casting direction.

This paper presents the experimental results for reinforcement effect for FRP strengthened steel structures. Bond behavior, flexural, and compression were conducted. First, from bond test, it was able to examine the interfacial behavior and to evaluate the interfacial bond stress between AFRP plate and steel plates. Second, for flexural test, maximum load was increased with increasing FRP layer. Also, debonding failure was observed between steel plates and FRP plates. Third, for compression, for short columns it was observed that two sides would typically buckle outward and the other sides would buckle inward. Also, for long columns, overall buckling observed. The maximum load was increased up to 33% for slender section short columns. From the test, it was able to verify the reinforcement effect for FRP strengthened steel structures.

The purpose of this paper is to evaluate bond capacity of steel fiber reinforced concrete. Test variables were compressive strength of concrete and steel bar diameter and a total of six specimens in order to examine the discrepancy in bond resistance due to each variable. The specimens were tested by using universal testing machine in displacement control mode. From the test results, it can be seen that the bond strength increased with increasing diameter of steel bar for the same compressive strength of concrete. Also, the higher strength concrete is, the higher bond strength can be found in the test. Significant slip resistance inducing greater bond strength can be observed in the specimens with large diameter steel bar. All the specimens failed in splitting failure after its maximum load and compressive stress of concrete predominated in bond capacity.

Recently, there are increasing cases utilizing the composite slab with a deck-plate for the simplicity of construction process and shortening of the construction period by eliminating the formwork and reinforcement placing works. General method of an existing deck-plate slab places welded wire fabric(w.w.f) for the crack control by drying shrinkage, however it was pointed out as its potential possibility for a number of cracks. In this study, long-term cracking behavior of deck-plate slab with the steel fiber was evaluated on the continuous two-span slab specimens that was designed on the general building loading condition.

The current study is a basic research to review the possibility of using steel wire from waste tires as recycled steel fiber for construction purposes. It analyzes preexisting waste tire-related data before processing and selecting waste steel wires to compare their composition and three quality standards if appearance as defined by concrete steel fiber regulations (KS F 2564), tensile strength, and flexibility, in order to review the feasibility of reusing waste steel wires. The results showed that the waste steel wires satisfy quality standards stated in the concrete steel fiber regulation (KS F 2564), indicating that they may be reused as recycled steel fiber for concrete.

In this study, We evaluated the applicability of high performance fiber reinforced cementitious composite (HPFRCC) with compressive strength of 180, 140 and 100 MPa and identical contents in steel fiber. The analysis of the flexure tensile behavior showed that HPRFCC presents deflection hardening after the initiation of cracks and exhibits higher energy absorbing capacity with high compressive strength.

In this study, impact performance of steel fiber-reinforced concrete was evaluated using existing impact formulae. The existing formulae were evaluated as to whether they can predict impact performance of steel fiber-reinforced concrete well.

본 연구는 폴리비닐 알코올 섬유 및 강섬유를 체적비율로 1.5% 혼입한 고인성 섬유보강 시멘트복합체에 대한 비상체의 고속충돌시험을 실시하고, 충돌조건에 따른 파괴특성을 실험적으로 검토하는 것을 목적으로 하였다. 비상체의 충돌에 의한 고인성 섬유보강 시멘트복합체의 파괴특성을 평가하기 위하여 화약압력식 충격시험장치를 활용하였으며, 충돌속도의 범위는 약 150 ~ 1,000m/s로 설정하였다. 파괴특성에 대한 평가결과, 고인성 섬유보강 시멘트복합체는 섬유를 혼입하지 않은 Plain시험체의 약 3배 이상의 비상체 운동에너지가 작용하는 범위에서도 표면관입의 파괴등급으로 평가되었으며, 시험체가 파단되지 않는 내충격성능이 확인 되었다. 또한, 충돌시험 전후에 대한 시험체의 질량감소율의 경우, Plain시험체는 비상체의 운동에너지의 증가율과 비례적인 관계를 보였지만, 고인성 섬유보강 시멘트복합체는 비상체의 운동에너지의 영향을 크게 받지 않는 것으로 나타났다. 특히, 이와 같은 경향은 시험체 배면의 파괴특성과 밀접한 관계를 가지며, S시험체에 비해 PVA시험체의 배면박리 억제효율이 큰 것으로 평가되었다. 한편, 국부손상에 대한 표면관입깊이 및 배면박리깊이의 관계를 검토한 결과, 고인성 섬유보강 시멘트복합체는 Plain과 달리 시험체 단면의 중앙선을 기준으로 배면에 가까운 영역에서 배면박리가 발생하는 것을 알 수 있었다. 본 연구를 통해 비상체의 충돌에 대한 고인성 섬유보강 시멘트복합체의 주요 파괴거동이 검토되었으며, Plain과 비교하여 내충격성능의 향상을 명확히 확인하였다.

In this study, we evaluate the chloride ion permeability of steel fiber rein-forced concrete. NT Build 492 experiment was used for the evalation. During the cast of SFRC, compaction works were done in same level. As a result, the chlorine ion permeability of the steel fiber rein-forced concrete is affected by Water-cement ratio. Effect of pores in the SFRC on permeability is dominant. In conclusion, it is important to get better quality of during cast in accordance with the addition of steel fiber ratio.

Recently, studies of eco-friendly construction materials have been increased. For this reason, this paper presents the material properties of steel fiber reinforced slag concrete. Direct shear, flexural, and CMOD tests were conducted to determine the shear and flexural contribution of steel fiber.

Earthquakes are very dangerous. They exemplify the true power of nature and cannot be avoid. Coupled shear walls are walls connected by moment- resisting members. The main subject investigated in this research project is the influence of steel fibers on the behaviour of coupling beams in shear.

본 연구에서는 모노파일지지구조의 고성능 그라우트연결부의 부착거동을 다루고 있다. 강관파일 연결부의 일체화를 위하여 섬유보강 고성능 그라우트를 개발하였으며, 재령 7일 압축강도 125MPa와 직인장강도 7.5MPa를 나타내었다. 축하중을 받는 상태에서의 그라우트의부착거동을 평가하기 위하여 강관파일에 그라우트를 충진하여 부착실험을 수행하였으며, 그 결과를 기존의 설계기준과 분석하였다. 실험변수는 섬유혼입율 (0%, 0.5% and 0.9%), 섬유의 형상비 (60 and 80)와 전단키의 높이와 간격의 비 (0.013 and 0.056)로 선정하였다. 실험결과 최대부착강도는 30.8MPa로 관찰되었으며, 섬유 혼입율보다는 전단키의 높이와 간격의 비가 부착강도에 영향을 미치는 것으로 분석되었다.

In this study, compressive capacity of Form-Block-Wall (FBW) was studied through prism test. Main variables are the difference in strength of grout concrete and steel fiber-reinforced block. The result showed that the strength of FBW increased corresponding to the increase of the strength of grout concrete and mortar. Also, it showed that steel fiber-reinforced FBW had a positive effect on prism strength and deformation capacity.

강섬유는 콘크리트 부재의 인장영역에 효과적으로 작용하여 균열저항성을 높여주고 역학적 성능을 개선하는 것으로 알려져 있다. 본 연구는 팽창재를 사용한 강섬유 모르타르에 화학적 프리스트레싱을 인가하여 균열저항성 및 역학적 성능을 평가하는 연구이다. 이를 위해 시멘트 바인더의 10%를 치환한 CSA 팽장채가 사용되었으며 체적비 1%의 강섬유를 고려한 시멘트 모르타르 배합이 준비되었다. 기본적인 역학적인 성능평가 외에 노치를 가진 보를 제조하여 초기균열하중 및 파괴에너지를 평가하였다. 실험결과 강섬유와 CSA 팽창재를 혼입한 모르타르에서는 보통 강섬유 모르타르에 비하여 평균 1.75배의 균열저항성 하중이 증가하였으며, 파괴에너지 역시 1.41~1.53배 증가하였다. 최적의 강섬유 체적비와 팽창재의 혼입이 고려된다면 강섬유의 내부 화학적 프리스트레싱을 가진 복합재는 다양한 부재에 사용될 수 있으며, 외부하중에 효과적인 균열저감 기법으로 사용할 수 있다.

The effect of steel fiber types on the self-sensing capacity of strain-hardening fiber-reinforced cementitious composites (SH-SFRCs) was investigated. Three types of fiber, including twisted, smooth and hooked fibers, were used with a volume content of 1.5% in a mortar matrix. Although all the SH-SFRCs exhibited self damage-sensing capacity, the gauge factor, representing for damage-sensing ability, was different according to the types of fiber as follows: twisted (138.09) > smooth (99.85) > hooked (88.50). The SH-SFRC with twisted fiber produced the highest gauge factor which is very favorable for development of self damage-sensor.

This paper describes the analysis results of coupling beams using steel fiber reinforced concrete for comparison with measure behaviors. Analysis is performed by the finite element analysis program, Vector 2. The results show possibility that relieve complex detail of diagonally reinforced coupling beam.

In this study, it was developed hybrid fiber reinforced concrete using ground granulated blast furnace slag, the industrial wastes, and recycled aggregate. As a result of experiments on improvement of performances of eco-friendly buildings utilizing recycled resources (recycled coarse aggregates and ground granulated blast furnace slag), the following conclusions are drawn. As hybrid fiber(PVA Fiber+ Steel Fiber) was mixed with the concrete in which the replacement was conducted with recycled coarse aggregates and ground granulated blast furnace slag, the structural performance were increased.

이 연구는 강섬유콘크리트를 사용하여 온도철근을 대체할 수 있는 가능성을 평가하기 위하여, 온도철근의 대체가 가능한 강섬유의 배합비를 결정하고 이에 따른 재료역학적 특성 및 경제성을 평가하였다. 강섬유는 길이 60mm, 직경 0.75mm를 사용하고, 배합비는 부피비로 0.2%, 0.5%, 1%를 사용하였다. 평가결과 강섬유 콘크리트가 강섬유의 혼입량과는 상관없이 일반 콘크리트보다 연성이 우수하고, 강섬유를 0.5% 혼입한 경우에는 온도철근을 배근한 경우보다 경제적으로 유리한 것으로 나타났다.

this study is experiment result of steel fiber reinforced concrete(SFRC) panel with flexural and impact resistance performance. The variables are the fiber volume fraction and aggregate size. The height and width of SFRC panels are 200 mm. The experimental results showed that flexural and impact resistant performance is improved by increased in steel fiber volume fraction.