The purpose of this study was to investigate the development of bovine nuclear transfer (NT) embryos cultured in serum-free conditions. Bovine NT embryos cultured in various culture conditions were compared blastocyst development, total cell number and apoptosis using TUNEL assay. In experiment 1, blastocyst rates of NT embryos were significantly higher (P<0.01) in FBS (22.0％) and BSA (26.6％) groups than in PVA (6.3％) group. Total cell number was significantly higher in FBS (78.4±19.4) and BSA (90.9±29.1) groups than in PVA group (46.0±0.0). Apoptotic cell number was significantly fewer in FBS (3.1±1.4) and BSA (1.7±1.4) groups than in PVA group (7.0±20.0) However, all of results were not different between the FBS and BSA group. In experiment 2, blastocyst rates of NT embryos were significantly higher (P<0.05) in fatty acid free-BSA (FAF-BSA) group (26.8％) than in fraction V-BSA group (11.2％). Total cell number were somewhat higher in FAF-BSA group (89.8±30.7) than in fraction V-BSA group (88.1±19.3). Apoptotic cell number were somewhat fewer in FAF-BSA (1.7±1.5) group than in fraction V-BSA group (4.2±2.9). These findings suggest that serum free condition were effective for the in vitro development of bovine NT embryos. Therefore, we concluded that fatty acid free-BSA has beneficial effect in development bovine NT embryos and can be use as a serum substitute.

Using a developed high-frequency induction heated combustion method. the simultaneous synthesis and densification of WC-xvol.%Co() hard materials was accomplished using elemental powders of W, C and Co. A complete synthesis and densification of the materials was achieved in one step within a duration of 1min. The final relative densities of the composite were over 98.5% for all cases, under the applied pressure of 60 MPa and the induced current. The hardness of the composites decreases and the fracture toughness increases with increasing cobalt content. As the carbon to tungsten ration increases, the hardness increase, but the fracture toughness decreases. The maximum values for the fracture toughness and hardness are 15.1 (at 20vol.%Co, W:C=1:1), and 1928 (at 5vol.%Co, W:C=1:1.3), respectively. Therefore we concluded that the HFIHCS method. which can produce WC-xvol.%Co within 1 minute in one step is superior to conventional ones.

1) Using a developed high-frequency induction heated sintering method, the rapid densification of WC-Co hard materials was accomplished using ultra fine powders with 260 nm size within 1 minute. 2) The relative density of the composite was 99.5% for the applide pressure of 60MPa and the induced current for 90% output of total capacity. 3) The grain size of WC-Co hard materials is about 260nm and the average thickness of the binder phase determined is about 11nm. The fracture toughness and the hardness of this work 12 , respectively. 4) Using pressureless sintering, we produced dense WC-Co hard materials with a relative density of 97% without applying pressure.

Recently, we have set up a new digital CCD camera system, MicroMax YHS-1300 manufactured by Roper Scientific for Hα observation by Solar Flare Telescope at Bohyunsan Optical Astronomy Observatory. It has a 12 bit dynamic range, a pixel number of 1300×1030, a thermoelectric cooler, and an electric shutter. Its readout speed is about 3 frames per second and the dark current is about 0.05 e-/p/s at -10°. We have made a system performance test by confirming the system linearity, system gain, and system noise that its specification requires. We have also developed a data acquisition software which connects a digital camera con-troller to a PC and acquires Hα images via Microsoft Visual C++ 6.0 under Windows 98. Comparisons of high quality Hα images of AR 9169 and AR 9283 obtained from SOFT with the corresponding images from Learmonth Solar Observatory in Australia confirm that our Hα digital observational system is performed properly. Finally, we present a set of Hα images taken from a two ribbon flare occurred in AR 9283.