Pultruded fiber reinforced polymeric plastic (PFRP) has many advantages such as high corrosion resistance, high specific stength/stiffness, light weight, etc. Pultrusion is a manufacturing process for producing continuous lengths of reinforced polymeric structural shapes with constant cross-section. The mechanical property of PFRP is usually regarded as an orthotropic material. The pultruded structural shapes are usually composed of thin-walled plate element. Because the composite material has relatively low elastic moduli, the design of pultruded compression members may not be governed by the material strength limit state but by the stability limit state such as the local buckling. Therefore, the stability limit state must be checked to design pultruded thin-walled compression members. In this paper, we present the analytical study results of elastic buckling strength of PFRP orthotropic plates with different fiber volume ratios. The local buckling analysis of pultruded compression members was conducted for various composite materials using the closed-form solution. From the study it was found that if E11/E22 is increased then the plate buckling coefficient, hence the plate buckling strength, is decreased.

In this paper, we present the result of analytical investigation pertaining to the structural behavior of steel-concrete composite plate girder with arch-type web stiffener. In the arch-type web stiffener located in the compression side of web, infill concrete is cast to strengthen the arch-type stiffener and also to exert resisting force against compression force. This type of composite steel-concrete plate girder bridge is built and is in service. To understand the behavior thoroughly, analytical parametric study was conducted by using the finite element method. As a result it was found that the effect of arch-type stiffener with infill concrete is considerable for the design of such type composite girder bridge.

FRP members which have light weight, high specific strength and stiffness, and good corrosion resistance are used widely in the electrical transmission system. Recently, FRP instead of steel, wood, and concrete tower is installed and in use. In this paper, we investigated the feasibility of replacement of traditional materials (steel, wood, and concrete) in electrical transmission towers by the fiber reinforced polymer plastic (FRP) members through the literature review. It was found that the FRP electrical transmission towers were applied in many countries due to its various advantages.

In recent years, the Glass Fiber Reinforced Polymer Plastic (GFRP) structural shapes are available in civil engineering applications. Among many manufacturing techniques used for GFRP structural shapes, pultrusion process is one of the most widely used techniques to produce the structural members in civil engineering applications. This study was focused on the mechanical behavior of singly bolted lap-joint connection with various hole clearances (tight-fit: 0.5mm, 1.0mm, 1.5mm, 2.0mm, 3.0mm) in Pultruded GFRP structural members. The specimens with single bolt-hole have been tasted in tension under bolt-loading conditions. The failed specimens were examined for their failure load and fracture patterns with respect to the various hole clearances.

Recently, the use of buried flexible pipes is widespread and ever increasing trend in the construction field. In this paper, we present the result of an investigation pertaining to the pipe stiffness of buried unplasticized polyvinyl chloride (PVC-U) pipes. To estimate the mechanical properties of PVC pipe produced by the domestic manufacturers, tensile test specimens were prepared and tested. In addition, parallel plate loading tests for the pipes with 150mm and 400mm inside diameters were conducted. From the test result, the pipe stiffness according to the ASTM D 2412 (2008) is estimated.

Pultruded glass fiber reinforced polymeric plastic (PFRP) and FRP member manufactured by sheet molding compound (SMC) have superior mechanical and physical properties compared with those of conventional structural materials. Since FRP has an excellent corrosion-resistance and high specific strength and stiffness, the FRP material may be highly appreciated for the development of floating-type photovoltaic (PV) power generation system. In this paper, advanced floating PV generation system made of PFRP and SMC is designed. In the design, it includes tracking solar altitude by tilting photovoltaic arrays and tracking solar azimuth by spinning structures. Moreover, the results of the finite element analysis (FEA) are presented to confirm stability of entire structure under the external loads. Additionally, installation procedure and mooring systems in the Hap-Cheon Dam are discussed and the measurement of strain under the actual circumstances is conducted for assuring stability of actually installed structures. Finally, by comparison with allowable stress, appropriate safety of structure is confirmed to operate the system.