This study examined the influence of operating parameters on the electrosorptive recovery system of lithium ions from aqueous solutions using a spinel-type lithium manganese oxide adsorbent electrode and investigated the electrosorption kinetics and isotherms. The results revealed that the electrosorption data of lithium ions from the lithium containing aqueous solution were well-fitted to the Langmuir isotherm at electrical potentials lower than –0.4 V and to the Freundlich isotherm at electrical potentials higher than –0.4 V. This result may due to the formation of a thicker electrical double layer on the surface of the electrode at higher electrical potentials. The results showed that the electrosorption reached equilibrium within 200 min under an electrical potential of –1.0 V, and the pseudo-second-order kinetic model was correlated with the experimental data. Moreover, the adsorption of lithium ions was dependent on pH and temperature, and the results indicate that higher pH values and lower temperatures are more suitable for the electrosorptive adsorption of lithium ions from aqueous solutions. Thermodynamic results showed that the calculated activation energy of 22.61 kJ mol–1 during the electrosorption of lithium ions onto the adsorbent electrode was primarily controlled by a physical adsorption process. The recovery of adsorbed lithium ions from the adsorbent electrode reached the desorption equilibrium within 200 min under reverse electrical potential of 3.5 V.

This study involves using nickel chloride solution as a raw material to produce nano-sized nickel oxide powder with average particle size below 50 nm by the spray pyrolysis reaction. The influence of the inflow speed of raw material solution on the properties of the produced powder is examined. When the inflow speed of the raw material solution is at 2 ml/min., the average particle size of the powder is 15~25 nm and the particle size distribution is relatively uniform. When the inflow speed of the solution increases to 10 ml/min., the average particle size of the powder increases to about 25 nm and the particle size distribution becomes much more uneven. When the inflow speed of the solution increases to 20 ml/min., the average particle size of the powder increases in comparison to the case in which the inflow speed of the solution was 10 ml/min. However, the particle size distribution is very uneven, showing various particle size distributions ranging from 10 nm to 70 nm. When the inflow speed of solution increases to 50 ml/min., the average particle size of the powder decreases in comparison to the case in which the inflow speed was 20 ml/min., and the particle size distribution shows more evenness. As the inflow speed of the solution increases from 2 ml/min. to 20 ml/min., the XRD peak intensities gradually increase, while the specific surface area decreases. When the inflow speed of solution increases to 50 ml/min., the XRD peak intensities rather decrease, while the specific surface area increases.

In this study, by using tin chloride solution as a raw material, a nano-sized tin oxide powder with an average particle size below 50 nm is generated by a spray pyrolysis process. The properties of the generated tin oxide powder depending on the inflow speed of the raw material solution are examined. When the inflow speed of the raw material solution is 2 ml/min, the majority of generated particles appear in the shape of independent polygons with average size above 80-100 nm, while droplet-shaped particles show an average size of approximately 30 nm. When the inflow speed is increased to 5 ml/min, the ratio of independent particles decreases, and the average particle size is approximately 80-100 nm. When the inflow speed is increased to 20 ml/min, the ratio of droplet-shaped particles increases, whereas the ratio of independent particles with average size of 80-100 nm decreases. When the inflow speed is increased to 100 ml/min, the average size of the generated particles is around 30-40 nm, and most of them maintain a droplet shape. With a rise of inflow speed from 2 ml/min to 5 ml/min, a slight increase of the XRD peak intensity and a minor decrease of specific surface area are observed. When the inflow speed is increased to 20 ml/min, the XRD peak intensity falls dramatically, although a significant rise of specific surface area is observed. When the inflow speed is increased to 100 ml/min, the XRD peak intensity further decreases, while the specific surface area increases.

정확한 in vitro 전사가 일어날 수 있는 진딧물의 세포추출액을 제조하였다. 전사를 직접 조절할 수 있는 단백질 인자를 규명하기 위하여 전사개시점과 그의 상류에 결합하는 DNA 결합단백질을 탐색했다. 전사개시점을 포함하는 단편 A(-194/23)에는 52kDa, 50kDa, 40kDa의 단백질들이 결합했으며 전사개시점 상류의 DNA 단편 B(-393/-263)에는 52kDa, 50kDa, 40kDa의 단백질들이 결합한 반면 DNA 단편 C(-263/-195)는 53kDa단백질만이 결합했다. 그리고 이들 DNA 결합단백질들의 DNA 결합 활성에는 양이온이 요구되었다.

Whistler mode chorus wave is considered to play a critical role in accelerating and precipitating the electrons in the outer radiation belt. In this paper we test a conventional scenario of triggering chorus using THEMIS satellite observations of waves and particles. Specifically, we test if the chorus onset is consistent with development of anisotropy in the electron phase space density (PSD). After analyzing electron PSD for 73 chorus events, we find that, for ~80 % of them, their onsets are indeed associated with development of the positive anisotropy in PSD where the pitch angle distribution of electron velocity peaks at 90 degrees. This PSD anisotropy is prominent mainly at the electron energy range of ≤ ~20 keV. Interestingly, we further find that there is sometimes a time delay among energies in the increases of the anisotropy: A development of the positive anisotropy occurs earlier by several minutes for lower energy than for an adjacent higher energy.

In vitro high-frequency plant regeneration of Muscari comosum var. plumosum through somatic embryogenesis was obtained via two developmental pathways: direct embryos and multiple shoots regenerated from embryogenic callus. Flower bud with pedicel, receptacle, petal and ovary wall, floral stalk and leaf as explants were cultured in MS medium supplemented with various plant growth regulators. Embryos formed directly from pedicel, receptacle and floral stalk. Depending on explant sources, the optimal medium was MS medium supplemented with 0.2 mg/L IBA and 0.3 mg/L BA, 3.0 mg/L IBA and 3.0 mg/L BA, and MS-free medium for pedicel, receptacle, and floral stalk, respectively. Multiple shoots regenerated from embryogenic cal]i which was initiated from petal, ovary and leaf were observed in MS medium with different concentrations and combinations of hormone. The most suitable medium for each type of explant was 3.0 mg/L IBA and 3.0 mg/L BA(petal and ovary) and 5.0 mg/L IBA and 5.0 mg/L BA (leaf) Furthermore, the combination of 0.1 mg/L 2,4-D and 1.0 mg/L BA was also good for all sources of explants not only for direct embryo formation, but also, for embryogenic callus induction.

Osmotic stress is one of major limiting factors in crop production. In particular, seasonal drought often causes the secondary disease in the field, resulting in severe reduction in both quality and productivity. Recent efforts have revealed that many genes encoding protein kinases play important roles in osmotic stress signal transduction pathways. Previously, the AtSIK (Arabidopsis thaliana Stress Inducible Kinase) mutants have shown to enhance tolerance to abiotic stresses, accompanying with higher expression of abiotic stress-related genes than did the wild-type plants. In this study, we have transformed potato (cv. Taedong Valley) with the AtSIK expression cassette. Both PCR and RT-PCR using AtSIK-specific primers showed stable integration and expression of the AtSIK gene in individual transgenic lines, respectively. Foliar application of herbicide (Basta®) at commercial application rate (0.3% (v/v)) revealed another evidence of stable gene introduction of T-DNA which includes the bar gene for herbicide resistance. Overexpression of the AtSIK gene under dual CaMV35S promoter increased sensitivity to salt stress (300 mM NaCl), which was demonstrated by the reduction rate of chlorophyll contents in leaves of transgenic potato lines. These results suggest that possible increase of osmotic tolerance in potato plants may be achieved by antisense expression of AtSIK gene.

Path planing method for an autonomous mobile robot is considered. For the practical applications, the simplified local potential field methods are applied under the constraints of the driving condition. To improve the performance, the fuzzy-approximated linear function method is also used.

Various light intensity and light quality were treated to oat seedlings to investigate the effect of light on the chlorophyll accumulation and the formation of chlorophyll-protein complexes. The increase of total chlorophyll accumulation and Chl (chlorophyll) a/b ratio was promoted under H (high intensity) white light during oat chloroplast development when compared to L (low intensity) white light. Also H white right was more effective in the formation of chlorophyll-protein complexes associated with PSI, CCI and CCII than L white light. The seedlings grown in various light quality caused little changes in total chlorophyll and Chl a/b ratio when compared to those grown in L white light. The assembly of LHCII trimer was more affected by L white light treatment in the formation of-chlorophyll-protein complexes than red light treatment. The effect of blue light on the relative composition of chlorophyll-protein complexes was similar to that of L white light. Particualrly, blue light was more effective in the synthesis of LHCII monomer than the other hot quality at the early stage of greening. When compared to red light, blue light was more effective in the formation of LHCII monomer. These results suggest that light intensity is more effective in the increase of chlorophyll accumulation and Chl a/b ratio than light quality, and light quality may be an important factor for the regulation of the organization in the chlorophyll-protein complexes during greening.