PURPOSES : The aim of this study is to evaluate the stripping resistance of a bead coating via the Hamburg wheel tracking test and image analysis. METHODS : First, the stripping resistance of the bead coating was evaluated via the Hamburg wheel tracking test. A pneumatic wheel with a load of 175±2 N was used to simulate repeated skid cycles. Several bead coating mixtures with different numbers of coating layers, i.e., zero, one, two, three, and four layers, i.e., zero, one, two, three, and four layers,were conducted. Finally, an image analysis program was developed to analyze surface images captured from the Hamburg wheel tracking test. RESULTS : The results show that the samples with more coating layers exhibit higher stripping resistance. After 500 stripping cycles, the percentage of bead loss is 4% to 28%. At 80% bead loss, the mixture with one coating layer presents more skid cycles than the control sample without a coating layer. CONCLUSIONS : Incorporating a coating layer can improve the stripping resistance of glass beads under repeated skid cycles. Additionally, an image analysis program is established in this study to determine the percentage of bead loss caused by the stripping test.

PURPOSES : The aim of this study is to evaluate the effects of air voids, binder content, and aggregate gradation on the indirect tensile strength (IDT) and cracking tolerance index (CTindex) of cored asphalt pavements. METHODS : Cored samples were obtained from roads in Incheon city, and several laboratory experiments were performed. First, the cored samples were first to cut into a size appropriate for the IDT test. Subsequently, the air voids of the samples were measured. The damaged sample from the IDT test was loose mixed at 150 ℃ before the binder content was determined, which was conducted via an asphalt extraction test. Finally, the clean aggregates obtained from asphalt extraction process were analyzed in the aggregate gradation test. RESULTS : The result shows that an increase in air voids from 4% to 8% decreases the IDT and cracking tolerance index (CTindex) by 30% and 28%, respectively. Incorporating a binder enhances the ductile behavior of the asphalt mixture, resulting in a higher CTindex. Finally, the contribution of the aggregate grade on the IDT and CTindex is negligible. CONCLUSIONS : The IDT and CTindex are primarily affected by the air voids and binder content. A higher percentage of air voids results in a lower IDT. In addition, a higher amount of binder increases the IDT and CTindex of the cored samples. Meanwhile, the aggregate grade does not affect the IDT.

PURPOSES : A mechanistic-empirical (ME) predictive design logic that can compute the reflective cracking life of hot-mix asphalt (HMA) overlaid on top of a composite pavement is proposed herein. METHODS : The overlay thickness design and analysis logic of the HMA were formulated based on the ME concept of reflection crack propagation. Climate data, traffic load data, the pavement material properties, and the thickness of each layer of the pavement are the main inputs for the ME-Reflective Cracking Rate (RCR) prediction algorithm. An Microsoft Excel Virtual Basic for Application (VBA) program was created to aid designers in assessing the expected performance of an HMA overlay design. Calibration was done using data from the Long-Term Pavement Performance (LTPP) sections. Sensitivity analysis was conducted to compare the results yielded by the program and data from a report by the Texas Transportation Institute. RESULTS : The predictive model performance effectively generates the dynamic and relaxation modulus curves. The correlation value of the calibration factors, R2, is 0.79. The calibration factors used for the Asphalt Overlay Thickness Design (AOTD) program and the sensitivity analysis, i.e., k1, k2,, and k3,, are set to 5, 5, and 150, respectively. The sensitivity of the AOTD program affords reasonable results. Additionally, the program yields results similar to the trends presented in a report by the Federal Highway Administration. CONCLUSIONS : The proposed ME design logic is successfully translated into an Excel VBA program, AOTD, which can perform routine assessments of laboratory tests for HMA overlays. The program can effectively perform numerous iterations and computations to predict an HMA overlay. The predictive model can generate reasonable dynamic modulus and relaxation modulus curves for the characterization of HMA overlays. Under the same asphalt binder grade and HMA type, doubling the HMA overlay thickness yields three times the expected reflective cracking service life.

PURPOSES : This study aims to determine the type (e.g., melting point, freezing point, latent heat fusion) and optimal content of phase change material (PCM) based on the numerical and experimental analyses evaluating the effects of heat transfer in PCM-modified asphalt pavement systems. METHODS : The effect of PCM on the thermophysical properties of PCM-modified asphalt concrete can be taken as an effective volumetric heat capacity. The volumetric fraction of PCM was calculated using an iterative method. The numerical model was established and computed using the MATLAB 2020 software. The optimum PCM design tool was developed to select the type and contents of the PCM. The PCM was chosen based on the following criteria: black-ice-formation delay time, minimize temperature increase, and increase temperature area. To validate the numerical model, asphalt mixtures were modified with varying PCM contents, and the temperature response of the PCMmodified asphalt samples was examined via temperature test. RESULTS : The numerical results showed that incorporating PCM into the asphalt mixture can slow the cooling rate of the pavement system. The predicted results from the optimum PCM design tool were highly consistent with the measured values from the laboratory temperature test. CONCLUSIONS : The temperature of PCM-modified asphalt pavement can be predicted via numerical method. The effect of PCM on the thermophysical properties can be considered as effective volumetric heat capacity; while the volume fraction of PCM can be calculated via an iterative method. The accuracy of the numerical model was confirmed by a high agreement between the measured and predicted values.

PURPOSES : The adhesive bonding strength of the grid between asphalt pavements is critical in pavement performance. The study is to compare and evaluate the interlayered bonding strength of asphalt mixture specimens with fiber-glass grid (FG) reinforcement and different tack coating materials based on the test results of the shear bonding test. METHODS : Asphalt mixtures were molded with FG reinforcement using various tack coating materials namely RSC4 and D/B coat. The adhesive shear-bond strength was measured by inducing a monotonic shear loadnig rate of 5 mm/min at 20℃. RESULTS : As expected, the asphalt mixture with non-reinforced FG exhibited the highest adhesive shear-bond strength, followed by that of the FG with D/B coating. The ranking order of superiority is as follows: Control (RSC4) > D/B+FG > RSC4+FG. CONCLUSIONS : The results of this experimental study indicate that FG with RSC4 and D/B tack coats can be successfully used in asphalt concrete overlay construction with superior field performance. Based on the test results and literature review, the field bonding strength should exceed 300kPa in grid reinforced asphalt pavement.