The structural safety of prototype transport and storage containers for very low-level radioactive liquid waste was experimentally estimated for its localization development. Transport containers for radioactive liquid waste have been researched and developed, however, there are no standardized commercial containers for very low-level radioactive waste in Korea. In this study, the structural safety of the designated IP-2 type container capable of transporting and temporarily storing large amounts of very low-level liquid waste, which is generated during the operation and decommissioning of nuclear power plants, was demonstrated. The stacking and drop tests, which were conducted to determine the structural integrity of the container, verified that there was no external leakage of the contents in spite of its structural deformation due to the drop impact. This study shows the effort required for the localization of the technology used in manufacturing transport and storage containers for very low-level radioactive liquid waste, and the additional structural reinforcement of the container in which the commercial intermediate bulk container (IBC) external frame was coupled.

Continuous synthesis of high-crystalline carbon nanotubes (CNTs) is achieved by reconfiguring the injection part in the reactor that is used in the floating catalyst chemical vapor deposition (FC-CVD) process. The degree of gas mixing is divided into three cases by adjusting the configuration of the injection part: Case 1: most-delayed gas mixing (reference experiment), Case 2: earlier gas mixing than Case 1, Case 3: earliest gas mixing. The optimal synthesis condition is obtained using design of experiment (DOE) in the design of Case 1, and then is applied to the other cases to compare the synthesis results. In all cases, the experiments are performed by varying the timing of gas mixing while keeping the synthesis conditions constant. Production rate (Case 1: 0.63 mg/min, Case 2: 0.68 mg/min, Case 3: 1.29 mg/min) and carbon content (Case 1: 39.6 wt%, Case 2: 57.1 wt%, Case 3: 71.6 wt%) increase as the gas-mixing level increases. The amount of by-products decreases stepwise as the gas-mixing level increases. The IG/ID ratio increases by a factor of 7 from 10.3 (Case 1) to 71.7 (Case 3) as the gas-mixing level increases; a high ratio indicates high-crystalline CNTs. The radial breathing mode (RBM) peak of Raman spectrograph is the narrowest and sharpest in Case 3; this result suggests that the diameter of the synthesized CNTs is the most uniform in Case 3. This study demonstrates the importance of configuration of the injection part of the reactor for CNT synthesis using FC-CVD.

We examined the adaptability of Korean winter forage crops such as Italian ryegrass, barley, oat, and triticale in Uzbekistan. The overall growth before wintering was slightly different between Uzbekistani and Korean varieties, but there was no significant difference among winter forage crops. The heading date of the Korean triticale 'Shinyoung' was the earliest, (April 4), and the heading date of the Uzbekistani triticale 'Frack cerebristy' was quite late, (April 25). The heading date of the Korean Italian ryegrass 'Kowinearly' was four days earlier than that of 'Kowinmaster,' on April 13, and that of the Korean barley ‘Youngyang’ and ‘Yuyeon’ were five days earlier than that of the Uzbekistani barley ‘Bolgaly’. The maximum dry matter yield of winter forage crop was from Uzbekistan triticale, 'Frack cerebristy', which was 13,536 kg/ha. The dry matter yield of Uzbekistan barley was 8,222 kg/ha. Compared with Uzbekistan barley, 'Bolgaly', yields of Korean barley 'Youngyang' and 'Yuyeon', Korean oat 'Samhan', and Korean Italian ryegrass 'Kowinearly' and 'Kowinmaster' were 59∼64%, 125%, and 113∼133%, respectively.

Free-standing electrodes of CuO nanorods in carbon nanotubes (CNTs) are developed by synthesizing porous CuO nanorods throughout CNT webs. The electrochemical performance of the free-standing electrodes is evaluated for their use in flexible lithium ion batteries (LIBs). The electrodes comprising CuO@CNT nanocomposites (NCs) were characterized by charge-discharge testing, cyclic voltammetry, and impedance measurement. These structures are capable of accommodating a high number of lithium ions as well as increasing stability; thus, an increase of capacity in long-term cycling and a good rate capability is achieved. We demonstrate a simple process of fabricating free-standing electrodes of CuO@ CNT NCs that can be utilized in flexible LIBs with high performance in terms of capacity and cycling stability.

This review presents current progress in the preparation methods of liquid crystalline nanocarbon materials and the liquid crystalline spinning method for producing nano-carbon fibers. In particular, we focus on the fabrication of liquid crystalline carbon nanotubes by spinning from superacids, and the continuous production of macroscopic fiber from liquid crystalline graphene oxide.

In this work, we report in-situ observations of changes in catalyst morphology, and of growth termination of individual carbon nanotubes (CNTs), by complete loss of the catalyst particle attached to it. The observations strongly support the growth-termination mechanism of CNT forests or carpets by dynamic morphological evolution of catalyst particles induced by Ostwald ripening, and sub-surface diffusion. We show that in the tip-growth mode, as well as in the base-growth mode, the growth termination of CNT by dissolution of catalyst particles is plausible. This may allow the growth termination mechanism by evolution of catalyst morphology to be applicable to not only CNT forest growth, but also to other growth methods (for example, floating-catalyst chemical vapor deposition), which do not use any supporting layer or substrate beneath a catalyst layer.

Most patients with chronic low back pain experience functional disability of trunk muscle, and limitations in physical activity. While there are many types of exercise programs available, in recent years sling exercise has been emerging as the exercise program for spinal stabilization. It has been supported by a great amount of research with positive findings on its effectiveness. This research studies the effects of bridging exercise, conducted on a sling, on pain level and trunk muscle activation in supine, sidelying, and prone positions during a 4 weeks period. 10 healthy people(normal group, n=10) and 28 patients with low back pain participated in this study. 28 patients were divided into two groups; one group participated in exercise with the sling(experimental group, n=14) and the other group exercised without the sling(control group, n=14). They were asked to use the Numerical Rating Scale(NRS) to answer to the level of their pain they felt (no pain: 0 point, severe pain: 10 points). During sling bridging exercises, the muscle activity level in each muscle measured in each position was standardized as three seconds of EMG signals during five seconds MVIC. In conclusion, the experimental group with four weeks of sling bridging exercise experienced a statistically significant reduction in the pain level(p<.05) and increase in the muscle activities of erector spinae when in supine position, internal oblique when in sidelying position, and rectus abdominis in prone position(p<.05). Regular sling bridging exercise reduces the low back pain and enhances other trunk muscle activation, thereby positively affect spinal stabilization.