For the final disposal of radioactive waste generated during the operation of nuclear power plants, concentrations of 14 radionuclides including gross alpha have to be determined to meet nuclear regulatory requirements. In order to determine the gross alpha radioactivity in radioactive waste, the sample must be preprocessed into a solution which is usually a strong acid. When this solution is used to prepare the gross alpha measurement sample, it produces a lot of salt, which makes an accurate measurement difficult. Also it causes corrosion of a planchet, which causes problems in the disposal of waste in the future. For these reasons, an acid treatment of the solution was added to the existing preprocess procedure, which is also expected to improve the measurement error. Although the gross alpha measurement is known to be easy to perform and able to give rapid results, it cannot be used for quantitative analysis. This is because the energies emitted by the individual alpha nuclides are assumed to be produced from a single alpha emitted by the individual alpha nuclides are assumed to be produced from a single alpha emitter used as the standard calibration source. Also, due to self-absorption of alpha particles a counting rate depends on the thickness (or weight) of the residues on the planchet. In this study, we compared gross alpha radioactivity with and without an acid treatment to prepare gross alpha measurement samples. The weights of the treated samples increased by at most 5% after about 12 hours of evaporation to dryness, and then saturated or slightly decreased, while the weights of the untreated samples increased up to 20% over time. In addition, the radioactivities of the untreated samples were about two times those of the treated samples. This is considered to be due to differences both in the geometric shapes of the samples and the weights of their residues which resulted from whether acid treatment was applied or not. The results of this study showed that an acid treatment was beneficial in reducing both production corrosion and salts which could result in more reliable and constant measurements of gross alpha activity. The results showed that acid treatment was beneficial in reducing corrosion and measurement errors.

To control pest of Brassicaceae leafy vegetable(leaf broccoli, Red Mustard Leaf, Tatsoi) which grows at vinyl house in IKSAN, Jeollabuk-do, the non-treatment was set as negative control, and treatment was divided into Parasitic natural treatment group and general treatment group. And incidence density of pest was surveyed and control effect was analyzed. As a result, in case of spring plants, the leaf damage ratio was decreased by 31% in Leaf broccoli, 30% in Red mustard leaf and 27% in Tatsoi compared to untreatment. In case of autumn plants, it was decreased by 32%, 41% and 17% respectively. The key pests were Plutella xylostella, Pieris rapae, Myus persicae Sulzer, Thrips palmi and Striped cabbage flea-beetle. Compared with the untreatment, the incidence density of each was significantly controlled. Other pests include Spodoptera exigua, Macdunnoughia purissima, Macdunnoughia purissima which showed high incidental density sometimes. In case of spring plants, the number by treatment was increased by 117% in Leaf broccoli, 85% in Red mustard leaf and 1,000% in Tatsoi. In autumn plants, it was increased by 132%, 257% and 1,077% respectively. The used Parasitic natural and eco-friendly materials were Cotesia glomerata, lacewing, ladyburg, Orius laevigatus, Encarsia formosa, Entomopathogenic nematode, Chungjigi and Togkaki. During early development of each pest, the Parasitic naturals were grazed 2~3 times at the interval of 7~10days. During the peak time, eco-friendly materials were sprayed 1~2 times. Based on this, comprehensive management model was drafted by period for each Brassicaceae vegetables pest.

To control Thrips tabaci in Korean leek and green onion which grow at vinyl house in IKSAN, Jeollabuk-do, the non-treatment was set as negative control. In general treatment group, 120 mesh gauze was installed on the side window after planting(May, 2nd) and, in spring, Orius strigicollis (1.0/m2) was grazed 3 times every 7 days from mid of May which is early development stage and In the mid of June, which is the peak stage, plant extracts were sprayed one time. In autumn, O. strigicollis was grazed 3 times every 7 days from mid of September which is early development stage, and in the mid of October, which is the peak stage, plant extracts were sprayed one time. The result shows that the leaf damage ratio was decreased by 22% in Korean leek and by 27% in green onion compared to the untreatment. And the control value of Thrips tabaci shows 78.7% in korean leak and 90.6% in green onion. The density control effect of Thrips tabaci was significantly controlled under max 6.2/plant in general treatment group compared max 25/plant in the untreatment and this result was similar in green onion. The yields by general treatment was increased by 85% in Korean leek and 56% in green onion, compared with non-treatment yields, which was 900kg/10a in Korean leek and 1,287kg/10a in green onion.

The aim of this investigation was to examine the influence of extrusion on dietary fiber profile and the contentof bioactive compounds, rutin and quercetin in young sprout, whole seed, and matured stem of Tartary buckwheat.WSI(water soluble index) is increased by a function of both screw profile and process temperature, compared to control indifferent parts of Buckwheat. Also, WSI of ME is increased more than 5.2 times in grain, compared to that of control. Theeffect of precooking by extrusion on the dietary fiber profile of buckwheat flour was evaluated. Precooking by extrusion sig-nificantly increased SDF in flour, although in most cases extrusion decrease in TDF a little. The thermo-mechanical treat-ment undergone by the buckwheat flour during extrusion led to redistribute part IDF fraction to SDF, leading to an increasein the latter. The content of rutin was increased about two fold in extruded flour of sprout, compared to in control. Thisincrease maybe why these compounds are released from cell wall by high shear processing under high temperature.