PURPOSES: The objective of this study is to evaluate and compare the stiffness characteristics and seasonal variation in surface deflections of block and asphalt pavements using the light weight deflectometer (LWD) and falling weight deflectometer (FWD). METHODS: LWD and FWD testing was conducted on block and asphalt pavement sections in a low-impact development facility, to evaluate the structural capacity and seasonal variation in asphalt pavements. To analyze the seasonal variation in stiffness characteristics, this testing was performed in October 2016, January 2017, and March 2017 in the same drop locations. RESULTS : It was found from that the average center deflections in the asphalt and block pavements were 218 ㎛ and 2974 ㎛, respectively. The center deflections measured using FWD testing in block pavement are 15 times those measured in asphalt pavement. It was also observed that LWD deflections in block pavements were decreased by approximately 65-90% as the air temperature dropped from 20 to 4℃. The degree of reduction in block pavement was significantly higher when compared with asphalt pavement, which showed a 25- 50% reduction in deflection. CONCLUSIONS: When using block pavements for roadways, the structural capacity of the pavement system should be considered during the design and construction stages. In block pavements, the use of low-quality material and insufficient compaction in the base and subgrade layers can induce a reduction in structural capacity, which would lead to the need for frequent repair work. A reinforcement underneath the block layer would be an appropriate measure for improving the structural support and extending the service life.

Spotted wing drosophila (SWD), Drosophila suzukii (Diptera: Drosophilidae), is an important quarantine insect pest on blueberry and strawberry exportation in Korea. Due to IPPC recommendations of replacement of methyl bromide (MB) and recent critical issue about its chronic inhalation toxicity to fumigator and related workers along with post-fumigation, alternatives to MB is urgently required. Thus, we evaluated efficacies of ethyl formate (EF) to SWD eggs using two different bioassay methods; using eggs oviposited on artificial diet and on blueberries naturally infested with SWD adults. In results, there was no differences between two bioassay methods in terms of LCT99 value of EF.

In Sri Lanka, the shoulder in asphalt pavements has been constructed using the materials transported from borrow pit in the iRoad Project due to the low quality of in-situ soils. After excavating 150~200mm thick and 500mm wide shoulder area, the borrow pit materials are placed and compacted according to specifications. The excavated in-situ soils are dumped in designated location. It is estimated that this process of shoulder construction is not economical due to high material transportation cost and can also induce the environmental issues by disposal of in-situ soils. It can also cause distresses such as surface rutting and edge drop-off in soft shoulder section due to bearing capacity failure and off-tracking of vehicle. The heavy rainfall in Sri Lanka can induce severe erosion problem when using the soft shoulder. To improve the strength and durability of pavement shoulders in the iRoad Project, the soil stabilization will be a good alternative to solve the above mentioned problems. The use of in-situ soils with addition of soil stabilizer enables to reduce the construction cost of shoulder section and mitigate the environment issues. The objective of this task is to review the application of soil stabilization method for soft shoulder construction in the iRoad Project. Firstly, the quantitative analysis of soil strength improvement due to soil stabilization was done for soil samples collected from iRoad construction sites. Two types of soils were selected from iRoad Project sites and prepared for soil stabilization testing by the Road Development Authority. Secondly, the appropriate stabilizer was selected at given soil type based on test results. Three different stabilizers, ST-1, ST-2, and ST-3, produced in Korea were used for estimating soil strength improvements. Finally, the optimum stabilizer content was determined for improving shoulder performance. The uniaxial compressive strength (UCS) test was conducted to evaluate the strength of stabilized soil samples in accordance with ASTM D 1633. The use of bottom ash as a stabilizer produced from power plant in Sri Lanka was also reviewed in this task.

Biochar obtained from the thermal conversion of biomass has high potential as a substitute material for activated carbon and other carbon-based materials because it is economical, environmentally friendly, and carbon-neutral. The physicochemical properties of biochar can also be controlled by a range of activation methods such as physical, chemical, and hydrothermal treatments. Activated biochar can be used as a catalyst for the catalytic pyrolysis of a biomass and as an absorbent for the removal of heavy metal ions and atmospheric pollutants. The applications of biochar are also expanding not only as a key component in producing energy storage materials, such as supercapacitors, lithium ion batteries, and fuel cells, but also in carbon capture and storage. This paper reviews the recent progress on the activation of biochar and its diverse present and future applications.

Refuse-derived fuel (RDF) produced using municipal solid waste was pyrolyzed to produce RDF char. For the first time, the RDF char was used to remove aqueous copper, a representative heavy metal water pollutant. Activation of the RDF char using steam and KOH treatments was performed to change the specific surface area, pore volume, and the metal cation quantity of the char. N2 sorption, Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), and Fourier transform infrared spectroscopy were used to characterize the char. The optimum pH for copper removal was shown to be 5.5, and the steam-treated char displayed the best copper removal capability. Ion exchange between copper ions and alkali/alkaline metal cations was the most important mechanism of copper removal by RDF char, followed by adsorption on functional groups existing on the char surface. The copper adsorption behavior was represented well by a pseudo-second-order kinetics model and the Langmuir isotherm. The maximum copper removal capacity was determined to be 38.17 mg/g, which is larger than those of other low-cost char adsorbents reported previously.

This study was to investigate pregnancy rate of IVM/IVF/IVC Korean cattle (registered in government) embryos according to transport time course. For the production of embryos, oocytes recovered from slaughtered excellent grade cow and highly motile frozen‐thawed bull semen (purchased from LIMC, KPN#497) was used. In vitro produced embryos were cultured in CR1aa medium for 8 days and some of them were frozen. The rate of average cleavage (>2‐cell) was 83.0% (308/371) and blastocyst rate at day 8 was 34.7% (107/308). Among in vitro produced blastocyst embryos at day 8, most healthy embryos were freshly transferred on production day and some frozen embryos were direct transferred on appropriate day. These embryos were produced in a laboratory, embryo transfer (ET) was planned in 10 areas of the remote island (Jeju) from the laboratory by airplane. Thus, we examined the pregnancy rate in recipient cow according to embryo of transport time course before ET. From embryo transferred 44 recipient cows, overall pregnancy was 40.9% (18/44), these 18 cows were all calved [single, 94% (17/18); twin, 6% (1/18)] and total embryo implantation rate was 26% (19/66). Comparing transport time in the base of 6 hr, pregnancy rate in ET group required less 4 hr (60%, 9/15) was significantly higher than that required more 6 hr (26.3%, 5/19). In direct ET of freezing embryos, the pregnancy rate was 40% (4/10). However, it was difficult to find the meaning of temperature, pH and corpus luteum quality of recipients on comparison of pregnancy rate. When the cell death level of embryos according to storage time in thermos (straw container) before ET was measured by TUNEL staining, apoptotic index was increased with storage time‐dependent. These results demonstrated that long distance transfer of IVM/IVF/IVC embryos is possible and the time of embryo transport is very important for the pregnancy rate on field trial.

본 연구에서는 4대강 살리기 사업 후 퇴적현상이 지배적으로 발생하는 남한강과 섬강 합류부 구간을 대상으로 2차원 수치모형인 CCHE2D 모형을 이용하여 하천의 흐름 및 하상변동에 대한 해석을 수행하였다. 대상지점 합류부는 남한강 본류의 만곡부에 지류 섬강이 유입되는 특성을 갖는다. CCHE2D 모형은 비평형 유사이송을 해석하며 소류사와 부유사 조정거리가 중요한 입력변수로 대상지점에서는 소류사 조정거리가 하상변동에 가장 큰 영향을 주는 것으로 나타났다. 수치모의 결과 유량비(Qr) 변화가 남한강과 섬강 합류부 지점에서 흐름 및 하상변동에 영향을 미쳤으며, Qr≤ 2.5인 경우에는 합류전 본류의 유속이 증가하여 흐름박리구역을 감소시켰으며 이로 인해 합류부 내측의 퇴적이 감소하였다. Qr>2.5이면 합류부 구간에 퇴적이 증가하여 사주가 형성될 가능성이 높은 것으로 나타났다. 수치모의를 통해 2013년에 발생한 유량비 변화에 의해 합류부에 고정사 주가 형성된 것을 알 수 있었다.

Cytoplasmic male sterility (CMS) and fertility restoration have been utilized as valuable tools for F_1-hybrid seed production in many crops despite laborious breeding processes. Molecular markers for the selection of CMS-related genes help reduce the expenses and breeding times. A previously reported genomic region containing the Ppr-B gene, which is responsible for restoration of fertility and corresponds to the Rfo locus, was used to develop gene-based or so-called "functional" markers for allelic selection of the restorer-of-fertility gene (Rfo) in F_1-hybrid breeding of radish (Raphanus sativus L.) Polymorphic sequences among Rfo alleles of diverse breeding lines of radish were examined by sequencing the Ppr-B alleles. However, presence of Ppr-B homolog, designated as Ppr-D, interferes on specific PCR amplification of Ppr-B in certain breeding lines. The organization of Ppr-D, resolved by genome walking, revealed extended homology with Ppr-B even in the promoter region. Interestingly, PCR amplification of Ppr-D was repeatedly unsuccessful in certain breeding lines implying the lack of Ppr-D in these radishes. Ppr-B could only be successfully amplified for analysis through designing primers based on the sequences unique to Ppr-B that exclude interference from Ppr-D gene. Four variants of Rfo alleles were identified from 20 breeding lines. A combination of three molecular markers was developed in order to genotype the Rfo locus based on polymorphisms among four different variants. These markers will be useful in facilitating F_1-hybrid cultivar development in radish.