In this study, we proposed a simulator for the development of a digital multi-process welding machine and a welding process monitoring system. The simulator, which mimics the data generation process of the welding machine, is composed of process control circuit, peripheral device circuit, and wireless communication circuit. Utilizing this simulator, we aimed to develop a welding process monitoring system that can monitor the welding situations of four multi-process welding machines and three processes each, with data transmission through wireless communication. Through the operation of the proposed simulator, sequential digital processing of multi-process welding data and wireless communication were achieved. The welding process monitoring system enabled real-time monitoring and accumulation of the process data. The selection of upper and lower limits for process variables was carried out using a deep neural network based on allowable changes in bead shape, enabling the management of welding quality by applying a process control technique based on the trend of received data.

In this study, the microstructure and characterization of an overlay welding layer using Fe-based composite powders are reported. The effects of the number of passes and composition of powders on the microstructure and mechanical properties are investigated in detail. The welding wire and powders are deposited twice on a stainless-steel rod using a laser overlay welding process. The microstructure and structural characterization are performed by scanning electron microscopy and X-ray diffraction. The mechanical properties of the first and second overlay layers are analyzed through the micro-Vickers-hardness tester and abrasion wear tester. In the second overlay layer, the hardness and specific wear are approximately 840 Hv and 2.0 × 10−5 mm3/Nm, respectively. It is suggested that the increase of the volume fractions of (Cr,Fe)7C3 and NbC phases in the second welding layer enhances the hardness and wear resistance.

구조용 강재의 용접부는 강재(Base metal, BM), 용접모재(Weld metal, WM), 열영향부(Heat affected zone, HAZ)로 구성된다. 용접부를 구성하는 이들 세 부분의 구조적 성질은 서로 다를 것이므로, 강재의 용접부의 구조 거동은 BM, WM, HAZ로 구성된 복합체의 거동으로 고려할 수 있다. 본 연구에서는 용접부를 구성하는 BM, WM, HAZ 각각의 탄성계수를 나노압입으로 도출하고, 이들의 복합거동(composite action)을 고려한 용접부의 등가탄성계수(equivalent elastic modulus)를 산정하였다.

Friction welding of particulate reinforced aluminum composites was performed and the following conclusions were drawn from the study of interfacial bonding characteristics and the relationship between experimental parameters of friction welding and interfacial bond strength. Highest bonded joint efficiency (HBJE) approaching was obtained from the post-brake timing, indicating that the bonding strength of the joint is close to that of the base material. For the pre-brake timing, HBJE was . Most region of the bonded interface obtained from post-brake timing exhibited similar microstructure with the matrix or with very thin, fine-grained layer. This was attributed to the fact that the fine-grained layer forming at the bonding interface was drawn out circumferentially in this process. Joint efficiency of post-brake timing was always higher than that of pre-brake timing regardless of rotation speed employed. In order to guarantee the performance of friction welded joint similar to the efficiency of matrix, it is necessary to push out the fine-grained layer forming at the bonding interface circumferentially. As a result, microstructure of the bonded joint similar to that of the matrix with very thin, fine-grained layer can be obtained.

개조한 가스 금속 아아크 용접공정을 이용하여 SiC/AI 금속기 복합재료를 제조하고 그 특성을 조사하였다. AI 모재위에 강화입자의 크기와 부피분율을 변화하여 다양한 SiC/AI 복합재료층을 제조하였고, 만들어진 복합재료층의 특성은 미세조직관찰과 미소경도시험을 통하여 이루어졌다. 복합재료층의 두께는 약 7-8mm로 측정되었고 균일한 강화입자의 분포도를 얻을 수 있었다. 분산입자의 부피분률은 Ar가스의 유량에 의하여 조절하였고 분산입자의 부피분률이 증가하고 크기가 작아짐에 따라 기지의 수지상 응고조직은 더욱 미세화되었다. 복합재료의 부피경도는 분산입자의 부피분률이 감소함에 따라 낮아졌으나 입자 크기에는 크게 변화가 없는 것으로 나타났다.