The influence of carbon surface area, carbon-oxygen groups associated with the carbon surface and the solution pH on the adsorption of Pb(II) ions from aqueous solutions has been studied using three activated carbons. The adsorption isotherms are Type I of BET classification and the data obeys Langmuir adsorption equation. The BET surface area has little effect on the adsorption while it is strongly influenced by the presence of acidic carbon oxygen surface groups. The amount of these surface groups was enhanced by oxidation of the carbons with different oxidizing agents and reduced by eliminating these groups on degassing at different temperatures. The adsorption of Pb(II) ions increases on each oxidation and decreases on degassing the oxidized carbons. The increase in adsorption on oxidation has been attributed to the formation of acidic carbon-oxygen surface groups and the decrease to the elimination of these acidic surface groups on degassing. The adsorption is also influenced by the pH of the aqueous solution. The adsorption is only small at pH values lower than 3 but is considerably larger at higher pH values. Suitable mechanisms consistent with the adsorption data have been suggested.

Removal of Pb(Ⅱ), Cu(Ⅱ), Cr(Ⅲ) and Zn(Ⅱ) ions from aqueous solutions using the adsorption process on domestic loess minerals has been investigated. Variations of contact time, pH, adsorption isotherms and selectivity of coexisting ions and leachate were experimental parameters. YDI, YPT and KRT samples diluted in 1% aquous solution which was adjusted pH 10.8, 8.0 and 6.50, respectively. The result of XRD measurement, Quartz was mainly observed in all samples. In the case of KRT sample, Kaolinite, Feldspar, Chlorite consisting of clay minerals shows almost same pattern with YPT samples. Different properties showed from the YDI sample containing Iillite, remarkably.For all the metals, maximum adsorption was observed at 30min ∼ 60min. Adsorption of metal ions on loess minerals were reached an equilibrium by shaking the solution for about 30min. Removal efficiency of Pb(Ⅱ) ion for KRT, YPT and YDI were 84.7%, 92% and 100%, respectively. The Cu(Ⅱ) and Zn(Ⅱ) adsorptivity on KRT showed the low in various pH solution However, those on YPT and YDI were high than 90% except for the pH 2 solution. The orders of adsorptivities for domestic loess minerals showed as following : YPT>KRT>YDI. The adsorption isotherms of Cu(Ⅱ) and Zn(Ⅱ) ions on clay minerals were fitted to a Freundlich's. Freundlich constants(1/n) of KRT and YPT domestic loess minerals were 0.63, 0.97 and 0.36, 0.25, respectively.

Surface complexation models(SCMs) have been performed to predict metal ion adsorption behavior onto the mineral surface. Application of SCMs, however, requires a self-consistent approach to determine model parameter values. In this paper, in order to determine the metal ion adsorption parameters for the triple layer model(TLM) version of the SCM, we used the zeta potential data for Zeolite and Kaolinite, and the metal ion adsorption data for Pb(Ⅱ) and Cd(Ⅱ). Fitting parameters determined for the modeling were as follows ; total site concentration, site density, specific surface area, surface acidity constants, etc. Zeta potential as a new approach other than the acidic-alkalimetric titration method was adopted for simulation of adsorption phenomena. Some fitting parameters were determined by the trial and error method. Modeling approach was successful in quantitatively simulating adsorption behavior under various geochemical conditions.

Cation exchange distribution coefficients of poly(dithiocarbamate) were presented for Cd^2+, Cr^3+, and Pb^2+ in HCl. The distribution coefficients were determined by using the batch method. Based on these distribution data, the separation possibilities of the heavy metal ions were discussed. The distribution coefficients of three heavy metal ions on dithiocarbamate resin were decreased as HCl concentrations were increased. The selective separation of Cr^3+ and Cd^2+ was possible by using 0.1 M HCl in dithiocarbamate resin and the reproducibility test showed that the average absorptivity of resin was 90% in the case of Cd^2+ ion by the column method.