검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 6

        1.
        2023.11 구독 인증기관·개인회원 무료
        If radioactive plumes are released outside due to loss of containment building integrity during a nuclear power plant accident, these materials might travel with the wind, affecting both the surrounding environment and neighboring countries. In China, most nuclear power plants are located on the eastern coast. Consequently, a radioactive plume generated during an accident could negatively impact even the western part of the Korean Peninsula due to westerly winds. To detect such problems early, respond quickly, and protect residents, a system that can monitor aerial radiation under normal conditions is needed. Additionally, a detection system that can operate in real-time in an emergencies conditions is required. The current method for aerial radiation measurement takes environmental radiation data from a monitoring post 1.5 m above the ground and converts it to altitude. To measure actual aerial radiation, an expansive area is surveyed by aircraft. However, this approach is both time-consuming and expensive. Thus, to monitor radioactive plumes influenced by environmental factors like wind, we need a radiation detector that can gauge both radioactivity and directionality. In this study, we developed a radiation detector capable of assessing both the radioactivity and directionality of a radioactive plume and conducted its performance evaluation. We miniaturized the radiation detector using a CZT (Cadmium Zinc Telluride) sensor, enabling its mounting on unmanned aerial vehicles like drones. It is configured with multi-channels to measure directionality of a radioactive plumes. For performance evaluation, we positioned two-channel CZT sensors at 90 degrees and measured the energy spectrum for angle and distance using a disk-type radioactive isotope. Using this method, we compared and analyzed the directionality performance of the multi-channel radiation detector. We also confirmed its capability to discern specific radioactivity information and nuclide types in actual radioactive plumes. Our future research direction involves mounting the multi-channel radiation detector on a drone. We aim to gather actual aerial radiation data from sensors positioned in various directions.
        2.
        2023.05 구독 인증기관·개인회원 무료
        Airborne surveys are an essential analysis method for rapid response and contamination identification in the early event of a radiation emergency. On the other hand, airborne surveys are far from the ground, so it is necessary to convert the dose rate at a height of 1 m above the ground. In order to improve the accuracy of the analysis value, a lot of analysis of the measurement data is required. In our previous research, we developed MARK-A1, an instrument for rapid radiation aerial survey in high radiation environment, and MARK-M1, a multipurpose instrument for radiation detection. In this study, a large unmanned aerial vehicle (UAV) was used to conduct airborne surveys using three types of detectors in the Jeju Island environment. The NaI(Tl) detector uses one 3-inch scintillator (38 mm φ × 38 mm H), and the LaBr3 detector uses two 2-inch scintillators (25 mm φ × 25 mm H). The CZT detector uses a detector with dimensions of (15 mm × 15 mm × 7.5 mm). The UAV has a payload of 15 kg (J10, JCH systems Inc. Seoul, Korea). Three different detectors were operated at a constant height of 20 m, 30 m, and 50 m. The flight experiments were performed in the west near Jeju City. Dose rate conversion factors were used to convert the dose rate from the measured spectra, and hovering flights were conducted between 1 and 50 meters to derive altitude correction factors. In this paper, the data measured with each detector in the same area were compared and the differences were derived.
        3.
        2022.10 구독 인증기관·개인회원 무료
        Investigations and monitoring of environmental radiation are important for preventing expected accidents or for early detection of unexpected accidents, in nuclear facilities and the surrounding. In the event of an environmental radiation accident, it should be possible to identify and analyze the radiation-contaminated area. Therefore, a rapid radiation monitoring system is required for immediate response and necessary measures. In this study, the distribution of radiation mapping is performed on a contaminated area using 2-dimensional or 3-dimensional contour mapping techniques. The entire surrounding area can be understood at a glance by displaying the radiation contour line on the map of the measured area.