During the initial cooling period of spent nuclear fuel, Cs-137 and Sr-90 constitute a large portion of the total decay heat. Therefore, separating cesium and strontium from spent nuclear fuel can significantly decrease decay heat and facilitate disposition. This study presents analytical technique based on the gas pressurized extraction chromatography (GPEC) system with cation exchange resin for the separation of Sr, Cs, and Ba. GPEC is a micro-scaled column chromatography system that allows for faster separation and reduction volume of elution solvent compared to conventional column chromatography by utilizing pressurized nitrogen gas. Here, we demonstrate the comparative study of the conventional column chromatography and the GPEC method. Cation exchange resin AG 50W-X12 (200~400 mesh size) was used. The sample was prepared at a 0.8 M hydrochloric acid solution and gradient elution was applied. In this case, we used the natural isotopes 88Sr, 133Cs, and 138Ba instead of radioactive isotopes for the preliminary test. Usually, cesium is difficult to measure with ICP-OES, because its wavelengths (455.531 nm and 459.320 nm) are less sensitive. So, we used ICP-MS to determine the identification and the recovery of eluate. In this study, optimized experimental conditions and analytical result including reproducibility of the recovery, total analysis time and volume of eluents will be discussed by comparing GPEC and conventional column chromatography.

The process of carbonization followed by a high-temperature halogenation removal of radionuclides is a promising approach to convert low-radioactivity spent ion-exchange (IE) resins into freereleasable non-radioactive waste. The first step of this process is to convert spent ion-exchange resins into the carbon granules that are stable under high-temperature and corrosive-gas flowing conditions. This study investigated the kinetics of carbonization of cation exchange resin (CER) and the changes in structures during the course of carbonization to 1,273 K. Both of model-free and modelfitted kinetic analysis of mixed reactions occurring during the course of carbonization were first conducted based on the non-isothermal TGAs and TGA-FTIR analysis of CER to 1,272 K. The structural changes during the course of carbonization were investigated using the high-resolution FTIR and C-13 NMR of CER samples pyrolyzed to the peak temperature of each reaction steps established by the kinetic analysis. Four individual reaction steps were identified during the course of carbonization to 1,273 K. The first and the third steps were identified as the dehydration and the dissociation of the functional group of —SO3-H+ into SO2 and H2O, respectively. The second and the fourth steps were identified as the cleavage of styrene divinyl benzene copolymer and carbonization of pyrolysis product after the cleavage, respectively. The temperature and time positions of the peaks in the DTG plot are nearly identical to those of the peaks of the Gram Schmidt intensity of FTIR. The structural changes in carbonization identified by high-resolution FTIR and DTG are in agreement with those by C-13 NMR. The results of a detailed examination of the structural changes according to NMR and FTIR were in agreement with the pyrolysis gas evolution characteristics as examined by TGA-FTIR.

Abstract Recently, the circular economy aiming at elimination of waste and the continual use of resources has attracted a lot of attentions. In the circular system, the resource recovery uses the recycled wastes as the raw material to manufacture new valuable products. This work focuses on a low-cost process, in which an activated carbon (AC) adsorbent was prepared from waste cation exchange resin by calcination and HNO3 activation hydrothermal method. Surface structure and chemistry of AC were characterized by SEM, XRD, FTIR and Boehm titration. It was found that the acid treatment could increase the number of pores and the content of oxygen-containing functional groups on AC surface. In the adsorption experiment, Methylene blue (MB) was used to assess the adsorption capacity of AC. Experimental results showed that the highest efficiency of MB removal was achieved by AC with modification of 4M HNO3, showing the acidification effect on the adsorption capacity of AC. Adsorption isotherms of Langmuir and Freundlich were employed to fit the experimental data. It was shown that MB adsorption on AC is more consistent with Langmuir model that assumes a homogeneous adsorption. In the adsorption kinetic analysis, the adsorption was found to follow the pseudo-second-order model, indicating that adsorption of MB on acidified AC is dominated by chemical adsorption. The study revealed that the waste ion-exchange resin is a proper precursor of carbon adsorbent for MB dye. This low-cost method would specifically reduce the environmental cost of waste disposal.

최근, 전세계적으로 물 부족 현상과 지역개발 및 산업 고도화, 인구증가와 함께 물 수요는 증가하고 있다. 이를 해결하기 위한 방법으로 해수담수화 방법이 있다. 해수 담수화의 많은 방법 중 이온 교환막을 이용한 실험을 진행하였다. 본 연구에서는 Anion exchange resin을 대체할 수 있는 물질로 Polystyrene Latex입자를 제조 하였다. 제조된 입자에 chloromethylation과 amination을 통해 –NH3+, -NR3+, -PR3+, -SR2+등의 관능기를 도입하였으며, 제조된 입자와 고분자를 합하여 하이브리드 막 제조를 하였다. 특성평가로는 SEM, TGA, DSC, FT-IR, IEC Value를 통한 측정을 진행하였다.

본 연구에서는 수계 내 포함된 양이온들 중 특히 중금속 이온을 효율적으로 분리할 수 있는 양이온 교환막을 개 발하였다. 기저 고분자로는 sulfonated polyetheretherketone (SPEEK)를 사용하였으며 이에 중금속 이온에 결합력이 강한 킬 레이팅 수지를 파우더링하여 첨가하였다. 또한 양이온 교환막의 성능을 최적화시키기 위해 킬레이팅 수지의 함량 및 SPEEK 의 이온교환용량을 제어하였다. 결과적으로 제조된 양이온 교환막을 막 축전식 탈염 공정(membrane capacitive deionization, MCDI)에 적용한 결과 중금속 이온 제거 효율이 20% 이상 향상됨을 확인할 수 있었다.

This study was conducted to know the removal characteristics of ammonia nitrogen by commercially available cation exchange resins. Eight acidic cation exchange resins were investigated in batch reactors. Among them, the most effective resin for ammonia removal in solution was PK228, which was a strong acidic resin of Na+ type. PK228 was compared with activated carbon and natural zeolite. The effects of cation exchange capacity, ammonia concentration, resin amount, temperature and pH on ammonia removal by PK228 were investigated in batch reactor, and the effect of effluent velocity in continuous column reactor. Strong acidic resins of porous type were more effective than week acidic resins or gel type resins for ammonia removal in solution. PK228 was more effective than activated carbon and natural zeolite for ammonia removal in batch reactor. With increasing initial ammonia concentration, the amount of ammonia removed by PK228 increased, but the proportion of removed ammonia to initial ammonia concentration decreased. The effect or temperature on ammonia removal by PK228 was very slight. The ammonia removal to acidic solution was more effective than that at basic solution. With decreasing effluent velocity of solution through column, breakthrough point extended, and ammonia removal capacity increased.