Floating PV generation system, renewable energy power plant, is able to overcome the disadvantages of ground PV generation system and improve generating efficiency. The frame structural system is an established technology among a diversity of structural technologies which has been developed for related fields. In this paper, the both structural safety and characteristics of floating PV generation structures depend on the different placement angle of solar module are investigated to improve the commercial viability, the structural safety, and characteristics of floating PV generation structures. In addition, for the estimation of structural safety, FE analyses are conducted. From the results, the lower placement angle of solar module improves the structural safety of floating PV generation system.

Recently, environmental problems associated with the excessive use of fossil fuel are hot issue throughout the world. As an alternative energy resource, the importance of renewable energy is continuously rising. Especially, growth rate of photovoltaic energy generation is one of the best. In this paper, floating PV generation system made of pultruded fiber reinforced polymeric plastic (PFRP) is discussed. It is well known that PFRP has many advantages such as high corrosion resistance, high specific strength/stiffness, etc. Compared with conventional construction materials. To investigate the structural behavior under flow induced dynamic loading, members and connections of members are tested under cyclic loading. It was found that the structural system is strong enough to resist such a cyclic loading.

The floating PV generation structure installed on the surface of water has been recently issued as a representative items for the low carbon and green growth campaign. Moreover, the studies and developments for the structure and construction improvements of floating PV generation structure have been in progress. For example, in the previous research, the floating PV generation structure consisted of pultruded FRP and SMC FRP members is suggested. In this study, we conduct the analytical and experimental studies for estimating the structural characteristics of SMC FRP vertical members. From the analytical and experimental results, it is found that SMC FRP vertical members used for floating PV generation structure have sufficient structural safety and stability.

Pultruded glass fiber reinforced polymeric plastic (PFRP) and FRP member manufactured by sheet molding compound (SMC) have superior mechanical and physical properties compared with those of conventional structural materials. Since FRP has an excellent corrosion-resistance and high specific strength and stiffness, the FRP material may be highly appreciated for the development of floating-type photovoltaic (PV) power generation system. In this paper, advanced floating PV generation system made of PFRP and SMC is designed. In the design, it includes tracking solar altitude by tilting photovoltaic arrays and tracking solar azimuth by spinning structures. Moreover, the results of the finite element analysis (FEA) are presented to confirm stability of entire structure under the external loads. Additionally, installation procedure and mooring systems in the Hap-Cheon Dam are discussed and the measurement of strain under the actual circumstances is conducted for assuring stability of actually installed structures. Finally, by comparison with allowable stress, appropriate safety of structure is confirmed to operate the system.

In this study, we conduct the economical analysis about the floating tracking PV generation structure manufactured by steel, aluminum, and GFRP (glass fiber reinforced polymeric plastic) structural member. The structural safety of floating PV generation structure has been proved through numerous previous researches. Moreover, the generating efficiency of tracking PV generation system can be more larger than immobile system. In this study, structural analysis using the FEM method has been performed to establish the safety of the floating tracking PV generation structure and commercial viability evaluation has been performed through the cost of materials.

Recently, environmental problems associated with the excessive use of fossil fuel are hot issue throughout the world. As an alternative energy resource, the importance of renewable energy is continuously rising. Especially, growth rate of photovoltaic energy generation is the best. In this paper, we present the result of investigations pertaining to the development of photovoltaic energy generation system installed on the sea. The system is consisted of photovoltaic energy generation panel, panel supporting structure, and floating structure. In the panel supporting structure, fiber reinforced polymer plastic (FRP) member manufactured by the pultrusion process is used. A floating type PV power generation structures shall be fabricated and this unit structure (I.e., module) is connected to extend to the appropriate size considering safety, workability, and economic efficiency. Developed floating type photovoltaic energy generation system is installed at fish farm in the south coast of Korea.

In this paper, the structural characteristics of the tracking-type floating PV generation system are presented. Moreover, the structural safety of each tracking-type floating PV generation system is estimated from the analytical results obtained by the finite element analyses.

The floating PV generation system is consisted of unit structures linked by the hinge type connection because the effect of bending moment in the structural system loaded due to the unstable movement of water surface can be minimized. In this paper, the investigation and development process of floating PV generation unit structure is presented.