Carbon dots (C-dots) are a developing subclass of nanomaterials which are characterized by a typical diameter of less than 10 nm. C-dots are a type of core–shell composites that feature a surface passivation with various functional groups, including amine, carboxyl, hydroxyl group, and a carbon core. Green C-dots, which have drawn a lot of interest from researchers due to their superior water solubility, excellent biocompatibility, and environmental-friendly behavior when compared to chemically generated C-dots, can be made from a variety of low-cost and renewable materials. Since green C-dots have heteroatoms on their surface in the form of carboxyl, amine, hydroxyl, or other functional groups, which can enhance their physicochemical characteristics, quantum yield (QY), and likelihood of visible light absorption, further surface passivation is not necessary. Green C-dots may find use in the areas of biosensing, catalysis, bioimaging, and gene and drug delivery. In this paper, the creation of C-dots was outlined, and its fluorescence process examined. This review represents the summary of synthesis, mechanism, properties, characterization, and applications of C-dots. This article aims at the green chemistry strategies for C-dot synthesis. Furthermore, a discussion on the applications of C-dots produced with green approaches is presented. The paper may help the researchers in the field to develop new C-dots with potential features to attract the attention of new applications.

Decontamination of spent nuclear fuel from decommissioned nuclear reactors is crucial to reduce the volume of intermediate-level waste. Fuel cladding hulls are one of the important parts due to high radioactivity. Their decontamination could possibly enable reclassification as low-level waste. Fuel cladding hulls used in research reactors and being developed for conventional light water reactors are Al-Mg and Fe-Cr-Al alloys, respectively. Therefore, the recovery of these component metals after decontamination is necessary to reduce the volume of highly radioactive waste. Electrochemical approach is often chosen due to its simplicity and effectiveness. Non-aqueous solvents, such as molten salts (MSs) and ionic liquids (ILs), are preferred to aqueous solvents due to the absence of hydrogen evolution. However, MSs and ILs are limited by high temperature and high synthesis cost, along with toxicity issues. Deep eutectic solvents (DESs) are synthesized from a hydrogen bond acceptor (HBA) and donor (HBD) and exhibit outstanding metal salt solubility, wide electrochemical window, good biocompatibility, and economic production process. These characteristics make DES an attractive candidate solvent for economic, green, and efficient electrodeposition compared with aqueous solvents such acids or nonaqueous solvents such as MSs or ILs. In this research, the feasibility of electrodeposition of Al-Mg and Fe-Cr-Al alloys in ChCl:EG, the most common DES synthesized from choline chloride (ChCl) and ethylene glycol (EG), will be tested. A standard three-electrode electrochemical cell with an Au plated working electrode and Al wires for counter and reference electrodes is utilized. Two electrolyte solutions (Al-Mg and Fe-Cr-Al) are prepared by dissolving 100 mM of each anhydrous metal chloride salts (AlCl3, MgCl2, CrCl3, and FeCl2) in ChCl:EG. Cyclic voltammogram (CV) is measured at 5, 10, 15, and 20 mV·s−1 to observe the redox reactions occurring in the solutions. Electrodeposition of each alloy is performed via chronoamperometry at observed reduction potentials from CV measurements. The deposited surfaces and cross-sections are examined by scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS) to analyze the surface morphology, cross-section composition, and thickness. Authors anticipate that the presence of different metals will greatly affect the possibility of electrodeposition. It is expected that although all metals are distributed throughout the surface, the morphology, in terms of particle size and shape, would differ depending on metals. Different metals will be deposited by layers of an approximate thickness of a few μm each. This research will illustrate a potential for recovery and electrodeposition of other precious radioactive metals from DES.

Increasing demand for fossil fuels is associated with massive atmospheric CO2 levels. Considering that numerous studies have been published with CO2 capturing techniques, utilizing techniques are yet in early stage with financial or technical issues. As a part of chemical conversion in CO2 utilization, this paper investigated the performance of a CO2 and H2O mixture (CHM) onto activated carbon fibers (ACF) for surface modification. CHM-treated ACF samples were prepared at a pressure of 20 bar with 100 °C of water vapor and 750 μL of CO2 for 1 h through the gas-phase, and labeled as C-ACF850. For the control sample, N-ACF850 was also prepared by the impregnation of nitric acid. Physiochemical analyses revealed that the overall characteristics of C-ACF850 lay between ACF850 and N-ACF850. C-ACF850 experienced minimized surface area decrement (21.92% better than N-ACF850), but increased surface functional groups (50.47% better than ACF850). C-ACF850 also showed preferable adsorption efficiency on selected metals, in which case both physical and chemical properties of adsorbent affect the overall adsorption efficiency. In this regard, a novel applicability of CHM may present an appealing alternative to traditionally used strong acids.