어군행동의 추정 및 제어등을 위한 기초자료의 제공과 어군행동의 모델링 기법을 현장에 적용하기 위한 가능성을 모색하기 위하여 어군행동을 나타내는 수치모델을 작성하고 유속이 있는 실험수조에서 유영하는 무지개송어를 대상으로 개체 및 어군의 3차원 위치 시계열 데이타를 이용하여 어군행동을 나타내는 수치 모델의 파라메터를 최소자승법으로 추정하였다. 어군행동을 나타내는 수치모델의 개체수 및 유속에 따른 파라메터 값의 변화를 조사하기 위하여 추정한 파라메터 값을 평균이 0이고, 분산이 1되게 파라메터를 표준화하여 비교한 결과를 요약하면 다음과 같다. (1) 개체의 전방추진력의 크기를 나타내는 파라메터 a*는 개체수 및 유속이 증가함에 따라 대체로 작아지는 경향을 나타내었다. (2) 개체 사이의 영향력의 크기를 나타내는 파라메터 kb*는 개체수가 많아짐에 따라 대체로 커지는 경향을 나타내었으나, 유속이 빠를수록 대체로 작아지는 것으로 나타났다. (3) 성군력의 크기를 나타내는 파라메터 kc*는 개체수 및 유속이 증가함에 따라 대체로 커지는 경향을 나타내었다. (4) 수조의 벽이나 바닥 등에 대한 반발력의 크기를 나타내는 파라메터 |kw+*|는 개체수가 많아짐에 따라 다소 커졌으나, 유속이 빠를수록 작아지는 것으로 나타났다. (5) 수조의 벽이나 바닥등에 대한 유인력의 크기를 나타내는 파라메터 |kw+*|는 개체수에 관계없이 대체로 일정한 것으로 나타났으나, 유속이 빠를수록 대체로 커지는 경향을 나타내었다. (6) 저항력의 크기를 나타내는 파라메터 v*는 개체수가 많아짐에 따라 다소 커지는 경향을 나타내었으나, 유속이 빠를수록 작아지는 것으로 나타났다.

Linear and nonlinear models are available to simulate the effect of mine blasting and the results change by each model. Linear model can properly simulate loss of impact wave in plastic failure region based on comparison of site vibration measurement and numerical analysis iteratively. But, loss of impact wave in plastic failure region should be calibrated into input parameter of blasting pressure. A method to convert loss of impact wave into design parameter is suggested in this study.

The bed change analysis near the opening gate of a dam or weir to release deposited sediments have been conducted mostly using the numerical models. However, the use of unverified input parameters in the numerical model is able to produce the different results with natural and real conditions. Also, the bed changes near the opening gate of a dam or weir calculated with a numerical model could be varied depending on the geometry extent included the downstream area with supercritical flow in the model. In addition, the different time steps could provide different results in the bed change calculation, even though other conditions such as input parameters, geometries, and total simulation time were same. Therefore, in this study, hydraulic experiments were performed to validate the eddy viscosity coefficient which is the one of important input parameters in the RMA2 model and relevant to variation of simulation results. The bed changes were calculated using the SED2D model based on flow results calculated in the RMA2 model with the verified and selected eddy viscosity coefficient and also compared with experimental results. The bed changes near the opening gate were underestimated in the numerical model comparing with experimental results except only the numerical case without the modeling section of sediment release pipe and downstream area where the supercritical flow was produced. For the simulation of minimum time steps, different shapes of scour hole were produced in numerical and physical modeling.

In order to make use of the protection effect against wind by the vegetation, it examined whether it should make what vegetation form and arrangement using the 2-dimensional non-hydrostatic model. When the foliage shielding factor increases, it becomes hard to take in protection effect against wind in a residential section. When it makes height of vegetation high, it becomes hard to take in protection effect against wind with height. In the comparison in the case where vegetation high is gradually made low toward wind-stream from a vegetation, and the case of making it low gradually, although former tends to receive the protection effect against wind by the vegetation, attenuation of wind velicity becomes large. In the comparison in the case where foliage shielding factor and distribution of density of leaf are gathered gradually toward wind-stream from a vegetation. It has been understood to evaluate to height the influence that the vegetation multi-layer model by which the heat revenue and expenditure in the direction of the vegetation height is considered is used, and to characterize the vegetation group by the parameter setting.