Recently, the electron transport layer (ETL) has become one of the key components for high-performance perovskite solar cell (PSC). This study is motivated by the nonreproducible performance of ETL made of spin coated SnO2 applied to a PSC. We made a comparative study between tin oxide deposited by atomic layer deposition (ALD) or spin coating to be used as an ETL in N-I-P PSC. 15 nm-thick Tin oxide thin films were deposited by ALD using tetrakisdimethylanmiotin (TDMASn) and using reactant ozone at 120 °C. PSC using ALD SnO2 as ETL showed a maximum efficiency of 18.97 %, and PSC using spin coated SnO2 showed a maximum efficiency of 18.46 %. This is because the short circuit current (Jsc) of PSC using the ALD SnO2 layer was 0.75 mA/cm2 higher than that of the spin coated SnO2. This result can be attributed to the fact that the electron transfer distance from the perovskite is constant due to the thickness uniformity of ALD SnO2. Therefore ALD SnO2 is a candidate as a ETL for use in PSC vacuum deposition.

Currently, Korea is actually increasing and increasing demand for leisure such as parts for A/S of automobile parts of the car, as well as trends in borrowing and finished parts are also required a steady increase in automobile traffic daetsu. There is one car and want to be driving a car A/S parts supplier smoothly for many years and that it is often the case if it is not supplied in a timely fashion, it is a reality that many eonseong hear from customers. These symptoms can be confirmed that the logistics systems of a system of selling auto parts supplier but above all a problem for several reasons, which will be considered as areas for improvement should be done urgently. Enterprises internally cooperation automotive supplier, but the need to get out to re-examine urgently complemented by the logistics system of systems to allow better respond to complex environmental changes of our customers grow, and now also the proliferation of small ship-run screen and Darvin , there is increasing distribution and logistics services, including logistics costs as a lack of work force that the company is itgetda can be called by the reality that the chances of getting a lot of jeyakreul own growth. Given this situation, the procurement of logistics enterprises. In-house logistics. Classified as sales logistics examined the long-term improvement of logistics distribution networks based on this part to derive into the problems of logistics and parts distribution system of Korean auto parts dealer.

고소성 점토 및 소성, 비소성 실트의 정규압밀상태시의 처녀압축곡선이 항상 선형적 거동을 하는 것은 아니며, 비선형성을 가진 한국의 남해안 점토의 경우 압밀압력이 증가함에 따라 압축지수가 감소하며, e-log σv'곡선은 아래로 오목한 형태의 거동을 하는 것으로 연구되었다. 본 연구에서는 한국 남부 해안의 점토를 대상으로 압밀시험을 수행하였고, 결과를 분석하여 초기간극비, 액성한계, 소성지수와 압축지수의 비선형성을 분석하였다. Butterfield의 기법을 이용한 lnv-ln σv'에서 액성한계 50~100%사이의 처녀압축곡선은 선형성을 보였으나, 초기간극비 2.24%, 액성한계 100%, 소성지수 60이상에서의 고소성 점토의 시험결과에서는 뚜렷한 비선형성이 나타났다. 비소성 실트(fly ash)를 90%이상 함유한 재성형 시료의 경우 압밀압력이 증가함에 따라 압축지수가 증가하는 경향을 보였다.

The bed change analysis near the opening gate of a dam or weir to release deposited sediments have been conducted mostly using the numerical models. However, the use of unverified input parameters in the numerical model is able to produce the different results with natural and real conditions. Also, the bed changes near the opening gate of a dam or weir calculated with a numerical model could be varied depending on the geometry extent included the downstream area with supercritical flow in the model. In addition, the different time steps could provide different results in the bed change calculation, even though other conditions such as input parameters, geometries, and total simulation time were same. Therefore, in this study, hydraulic experiments were performed to validate the eddy viscosity coefficient which is the one of important input parameters in the RMA2 model and relevant to variation of simulation results. The bed changes were calculated using the SED2D model based on flow results calculated in the RMA2 model with the verified and selected eddy viscosity coefficient and also compared with experimental results. The bed changes near the opening gate were underestimated in the numerical model comparing with experimental results except only the numerical case without the modeling section of sediment release pipe and downstream area where the supercritical flow was produced. For the simulation of minimum time steps, different shapes of scour hole were produced in numerical and physical modeling.

본 연구에서는 솔잎분말을 첨가하여 기능성식빵을 제조하기 위한 반죽의 품질특성을 조사하였다. 일반 성분측정 결과 생 솔잎은 수분 58.1%, 조단백질 4.5%, 조지방 3.9%, 조회분 0.9%, 식이섬유량 9.3%로 나타났다. 반죽의 pH 측정 결파 대조구의 pH는 5.9, 솔잎분말 첨가시에는 범위로 나타났다. 반죽의 호화도는 솔잎분말 첨가량이 증가함에 따라 호화 개시 온도는 증가하였고 최고 점도는 감소하였다. 반죽의 falling numbe