Porous graphene oxide (P-GO) was successfully synthesized by using a simple glucose mediated hydrothermal method form prepared graphene oxide (GO). Then the P-GO was characterized by X-ray Powder Diffraction (XRD), Fourier-Transform Infrared (FITR), Raman, Brunauer–Emmett–Teller (BET), Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) analysis to determine the crystallinity, surface functionality, surface defect, surface area and porous nature of the material. For the comparative properties studies with P-GO, the synthesised GO was also characterised using the aforementioned analytical techniques. The formation of macroporous 2D sheet-like structure of P-GO with pore size diameters of 0.2–0.5 μm was confirmed by FESEM and TEM images. The surface area of P-GO was found to be 1272 m2/ g which is much higher compare to GO (i.e., 172 m2/ g) because of porous structure. P-GO was used for the adsorptive removal of F− ions from water using batch adsorption method. The highest adsorption occurs in the pH range of 5–7 with maximum adsorption capacity of 1272 mg/g. The experimental data revealed that the adsorption process obeys Langmuir monolayer isotherm model. The kinetic analysis revealed that the adsorption procedure is extremely rapid and mainly fit to the Pseudo-second-order (PSO) model. The effect of co-existing ions on fluoride adsorption capacity by P-GO decreases in the following order: PO4 3− > CO3 2− > SO4 2− > HCO3 − > NO3 − > Cl−. The mechanism of adsorption of fluoride onto the P-GO surface includes electrostatic interactions and hydrogen bonding.

Research on Graphene and its importance in the field of energy conversion and storage devices such as fuel cells, batteries, supercapacitors and solar cells has gained momentum recently. It is studied to be the most suitable electrode material for enhanced performance of supercapacitors in terms of charge–discharge cycles, specific capacitance, high power and energy densities and so on, specifically due to its high conductivity and large theoretical surface area. Unfortunately, it posits lot of challenges due to its irreversible stacking between the individual sheets resulting in the decrease in the Specific Surface Area (SSA) compared to the theoretically reported values. Numerous studies have been carried out to prevent this stacking in order to increase the surface area, thereby being a more suitable material for the manufacture of electrodes for supercapacitors as its capacitance greatly depends on the electrode material. To solve this problem, the conversion of two-dimensional graphene sheets to three-dimensional crumpled graphene structure has been verified to be the most effective approach. The study of crumpled graphene has been one of the recent trends in the field of energy storage applications in consumer electronics and hybrid vehicles as the process of crumpling can be controlled to suit the prospective device applications.

The present work focused on the determination of texture, morphology, crystallinity, and gas adsorption characteristics of porous graphene prepared from rice husks ashes at different stabilization temperature. The stabilization temperature applied in this work is 100 °C, 200 °C, 300 °C, and 400 °C to convert rice husk into rice husk ashes (RHA). Chemical activation was adopted at temperature 800 °C using potassium hydroxide (KOH) as dehydrating agent at (1:5) impregnation ratio to convert RHA into rice husk ashes-derived graphene (GRHA). The resultant GRHA were characterized in terms of their morphological changes, SSA, crystallinity, and functional group with TEM, the BET method, Raman spectroscopy, and XRD analysis, respectively. Results from this study showed that the SSA of the GRHA at stabilization temperature 200 °C (1556.3 m2/g) is the highest compared to the other stabilization temperature. Raman spectroscopy analysis revealed that all GRHA samples possess D, G, and 2D bands, which confirm the successful synthesis of the rice husks into porous graphene-like materials, known as GRHA. Appearance of diffraction peak in XRD at 44.7° indicating the graphitic structure of all the GRHA samples. Meanwhile, the TEM images of GRHA200 exhibited wrinkled structures due to the intercalation of oxygen and a few layers of graphene flakes. These wrinkled structures and graphene layers are the other factors that lead to the highest SSA of GRHA200 compared to other prepared samples GRHA. Furthermore, the adsorption capacity of CH4 for GRHA200 is up to 43 cm3/g at 35 bar and ambient temperature, almost double the adsorption capacity performance of GRHA400 at the same operating pressure and temperature.

The study presented in the article is focused on use of graphene obtained by novel microwave-enhanced chemical vapor deposition (MECVD) method as a construction material for 3D porous structures—aerogels and sponges. MECVD graphene nanoplatelets-based aerogels were obtained by mixing MECVD graphene nanoplatelets and chitosan, dissolved in 3% acetic acid followed by its freeze drying and carbonization at 800° in inert medium. Surface morphology of aerogels was characterized by SEM. MECVD graphene nanoplatelets-based aerogels are characterized by a porous structure; they are superhydrophobic and possess high sorption capacity with regard to organic liquids of different densities. Polyurethane sponges coated with MECVD graphene can serve as an alternative to aerogels. The process of their obtaining is cheaper and less complicated. They were obtained by facile “dip-coating” method, modifying its surface to increase its hydrophobicity. The resulting sponges are superhydrophobic and superoleophilic, and demonstrate high rate of sorption of organic liquids and can be easily regenerated by squeezing. In addition, they can be used as a separating material in conjunction with vacuum system for continuous and selective collection of organic liquids from the surface of water.

Porous materials play a vital role in science and technology. The ability to control their pore structures at the atomic, molecular, and nanometer scales enable interactions with atoms, ions and molecules to occur throughout the bulk of the material, for practical applications. Three-dimensional (3D) porous carbon-based materials (e.g., graphene aerogels/hydrogels, sponges and foams) made of graphene or graphene oxide-based networks have attracted considerable attention because they offer low density, high porosity, large surface area, excellent electrical conductivity and stable mechanical properties. Water pollution and associated environmental issues have become a hot topic in recent years. Rapid industrialization has led to a massive increase in the amount of wastewater that industries discharge into the environment. Water pollution is caused by oil spills, heavy metals, dyes, and organic compounds released by industry, as well as via unpredictable accidents. In addition, water pollution is also caused by radionuclides released by nuclear disasters or leakage. This review presents an overview of the state-of-the-art synthesis methodologies of 3D porous graphene materials and highlights their synthesis for environmental applications. The various synthetic methods used to prepare these 3D materials are discussed, particularly template-free self-assembly methods, and template-directed methods. Some key results are summarized, where 3D graphene materials have been used for the adsorption of dyes, heavy metals, and radioactive materials from polluted environments.

Graphene oxide (GO) has been extensively studied for membrane material for gas and liquid separation due to its outstanding features such as selective CO2 or water vapor transport properties. Although GO membranes can be easily fabricated in the form of thin-film composite membranes by using high-flux polymeric support membranes, it shows relatively low gas permeability due to high tortuosity. Here we report the way to improve gas permeation rate through porous graphene oxide by reducing the gas permeation pathway, with maintaining GO’s two-dimensional structure. We also used polymer, which has high CO2/N2 selectivity, and prepared GO/polymer composite membranes as a function of GO concentration. This study will provide a further insight on how such two-dimensional nanosheets can be harmonized with polymer and improved membrane properties.