간행물
Carbon Letters KCI 등재 Carbon letters
- 발행기관 한국탄소학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1976-4251 (Print)2233-4998 (Online)
- 수록기간 2000 ~ 2024
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
Vol.34 No.1 (2024년 1월) 42건
1.
2024.01
구독 인증기관 무료, 개인회원 유료
We present a practical vacuum pressure sensor based on the Schottky junction using graphene anchored on a vertically aligned zinc oxide nanorod (ZnO-NR). The constructed heterosystem of the Schottky junction showed characteristic rectifying behavior with a Schottky barrier height of 0.64 eV. The current–voltage (I–V) features of the Schottky junction were measured under various pressures between 1.0 × 103 and 1.0 × 10− 3 mbar. The maximum current of 38.17 mA for the Schottky junction was measured at – 4 V under 1.0 × 10− 3 mbar. The high current responses are larger than those of the previously reported vacuum pressure sensors based on ZnO nanobelt film, ZnO nanowires, and vertically aligned ZnO nanorod devices. The pressure-sensitive current increases with the vacuum pressure and reaches maximum sensitivity (78.76%) at 1.0 × 10− 3 mbar. The sensitivity and repeatability of the Schottky junction were studied by the current–time (I–T) behavior under variation of vacuum pressure. The sensing mechanism is debated from the surface charge transfer doping effect by oxygen chemisorption. The results suggest that this simple graphene/ZnO-NR Schottky junction device may have potential in the fabrication of vacuum pressure sensor with high sensitivity.
4,200원
2.
2024.01
구독 인증기관 무료, 개인회원 유료
C. Bhagya Lakshmi, S. Anna Venus, S. Velanganni, A. Muthukrishnaraj, Manikandan Ayyar, Mohamed Henini
Photoanode optimization is a fascinating technique for enlightening the power conversion efficiency (PCE) of dye-sensitized solar cells (DSSCs). In this present study, V2O5/ ZnO and reduced graphene oxide (rGO)-V2O5/ZnO nanocomposites (NCs) were prepared by the solid-state technique and used as photoanodes for DSSCs. A wet chemical technique was implemented to generate individual V2O5 and ZnO nanoparticles (NPs). The structural characteristics of the as-synthesized NCs were investigated and confirmed using powder X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), and Scanning electron microscope (SEM) with energy dispersive X-ray (EDX) analysis. The average crystallite size (D) of the as-synthesized V2O5/ ZnO and rGO-V2O5/ZnO NCs was determined by Debye-Scherer’s formula. The bandgap (eV) energy was calculated from Tauc’s plots, and the bonding nature and detection of the excitation of electrons were investigated using the Ultra violet (UV) visible spectra, Fourier Transform infrared (FTIR) and photoluminescence (PL) spectral analysis. Electrical studies like Hall effect analysis and the Nyquist plots are also described. The V2O5/ ZnO and rGO-V2O5/ZnO NCs based DSSCs exhibited 0.64% and 1.27% of PCE and the short circuit current densities and open circuit voltages improved from 7.10 to 11.28 mA/cm2 and from 0.57 to 0.68 V, respectively.
4,300원
3.
2024.01
구독 인증기관 무료, 개인회원 유료
Aqueous Zn-ion batteries (ZIBs) are very attractive owing to their high safety and low cost. Among various cathode materials, organic materials-based electrodes incorporating various redox functional groups have gained significant attention in the field of ZIBs due to their benefits of a tunable structural design, facility, eco-friendly, and possibility of multivalent energy storage. Herein, we demonstrate the nanostructured organic active materials deposited onto the CNT networks (HyPT@ CNT) for flexible ZIBs. This HyPT nanorods were obtained reassemblying the herringbone structured 3,4,9,10-tetracarboxylic dianhydride through a hydrothermal process in the presence of acid. These HyPT@CNT hybrids were electronically conductive and redox active, as well as could be fabricated into a flexible electrode achieving flexibility from mechanical integrity of robust networked structure. The as-fabricated flexible ZIBs delivered the high capacity of 100 Ah g− 1 at a current density of 0.1 A g− 1 and long-term cycling performance exceeding 5000 cycles. Consequently, these electrochemical performances are associated with the redox reactivity of carbonyl groups as verified by spectroscopic and electrochemical characterizations and the hybridization of HyPT nanorods with CNT networks.
4,800원
4.
2024.01
구독 인증기관 무료, 개인회원 유료
Banoth Reddy, Amit Kumar Taneja, Mandava Bhuvan Tej, Komati Navya Sri, Mandava Bhagya Tej, Suryadevara Vijayavardhini, Dandamudi Srilaxmi, Somasekhar Tiruveedhula, Srinivasa Rao Penumutchu, Mandava V. Basaveswara Rao
New tetrazole fused imidazopyridine derivatives (12a–j) were developed to exploit their cytotoxic activity towards cancer cell lines-MCF7, A549, and MDA-MB-231, utilizing MTT reduction assay with doxorubicin as standard drug. The compounds 12 h and 12j demonstrated strong anticancer activity bearing IC50 values 1.44 μM and 1.33 μM against A549 cell line.
4,000원
5.
2024.01
구독 인증기관 무료, 개인회원 유료
β-Resin was extracted by solvent separation of refined coal tar pitch. Several analytical methods revealed that β-resin had a better aromatic plane packing structure and a higher number of carbon residues, making it ideal for mesophase transformation. The mesophase transformation process of β-resin (the formation of liquid-crystalline spheres, the growth of mesophase spheres, and the coalescence and disintegration of mesophase spheres) was observed in situ using a polarizing microscope with a hot stage. Moreover, the mesophase transformation mechanism of β-resin was investigated at each transformation stage. The mesophase content and mesophase transformation kinetics were analyzed based on the area method and quinoline insoluble (QI) substitution method. Both methods revealed changes in the mesophase content of β-resin. However, the test results of the two methods were slightly different at the initial stage of mesophase transformation and tended to be consistent during the later stage.
4,500원
6.
2024.01
구독 인증기관 무료, 개인회원 유료
Fluorine heteroatoms were introduced to increase the limited specific capacitances of electric double-layer capacitors (EDLCs), and the effects of the fluorine atoms were analyzed. To introduce the fluorine, a CF4 plasma treatment was used that introduced the fluorine atoms quickly. Among the fluorine functional groups in the F6-ACA framework, the semi-ionic C–F bonds induced rapid charge transfer and imparted pseudocapacitance. Consequently, we achieved a specific capacitance of 325.68 F/g for the F6-CA sample at 0.5 A/g. By analyzing the contributions of the electric double-layer capacitance and the pseudocapacitance, we determined that the contribution from the pseudocapacitance was 37.57%. A remarkable specific capacitance retention rate of 95.87% was obtained over 1000 charge/discharge cycles with a high current density of 3 A/g. Additionally, the semi-ionic C–F bonds reduced the charge transfer resistance ( Rct) by 36.8%. Therefore, the specific capacitance was improved by the fluorine heteroatoms, and the semi-ionic C–F bonds played a pivotal role in this improvement.
4,000원
7.
2024.01
구독 인증기관 무료, 개인회원 유료
Fe3O4/g-C3N4/TiO2 catalyst has been fabricated using a simple ultrasonic method with high photocatalytic activity. The morphology, structure and optical properties of Fe3O4/ g-C3N4/TiO2 were systematically investigated by a variety of characterization techniques. The optimum degradation conditions were investigated by degrading tetracycline (TC) under visible light irradiation. The results showed that the degradation efficiency was the highest when the initial TC concentration was 5.0 mg/L, the pH value was 11 and the catalyst dosage was 1.0 g/L. After 100 min of visible light irradiation, the degradation efficiency of TC achieved at 73.61%, which was 1.64 and 1.19 times that of g-C3N4 and Fe3O4/ g-C3N4, respectively. Moreover, Fe3O4/ g-C3N4/TiO2 had good stability and recyclability. The results of capture experiments showed that ‧O2 − and ‧OH were the main active species during the photocatalytic process, and a possible photocatalytic reaction mechanism of Fe3O4/ g-C3N4/TiO2 catalyst was proposed. This study provides a new way to improve the photocatalytic performance of g-C3N4, which has great potential in degrading pollutants such as antibiotics in wastewater.
4,000원
8.
2024.01
구독 인증기관 무료, 개인회원 유료
N-doping content and configurations have a significant effect on the electrochemical performance of carbon anodes. Herein, we proposed a simple method to synthesize highly N self-doped chitosan-derived carbon with controllable N-doping types by introducing 2ZnCO3 ·3Zn(OH)2 into the precursor. The as-synthesized NC-CS/2ZnCO3·3Zn(OH)2 electrode exhibited more than twice the reversible capacity (518 mAh g− 1 after 100 cycles at 200 mA g− 1) compared to the NC-CS electrode, superior rate performance and outstanding cycling stability. The remarkable improvement should be mainly attributed to the increase of N-doping content (particularly the pyrrolic-N content), which provided more active sites and favored Li+ diffusion kinetics. This study develops a cost-effective and facile synthesis route to fabricate high-performance N self-doped carbon with tunable doping sites for rechargeable battery applications.
4,000원
9.
2024.01
구독 인증기관 무료, 개인회원 유료
Carbon-based materials, particularly graphite, have been extensively studied for their potential in fabricating flexible conductive fabrics with high electrical conductivity, which are attractive for wearable electronics. In this study, we investigated the effects of polar solvents, graphite concentration, and temperature on the electrical properties of conductive cotton fabrics. Our results show that the type of polar solvent and graphite concentration strongly influence the electrical conductivity of the fabrics. By controlling the graphite concentration, a wide range of conductive cotton fabrics with different conductivity values can be produced. Additionally, temperature resistance studies revealed that the fabrics exhibit both semiconductor and metallic behavior in the temperature range from room temperature to 160 °C. These interesting properties make the conductive cotton fabrics suitable for use as electrical components in circuits with resistive and inductive loads. Furthermore, we fabricated a supercapacitor with electrodes based on dispersed graphite and an electrolyte of sodium chloride salt dissolved in deionized water. Our findings suggest that conductive cotton fabrics have great potential for use in high-performance wearable electronics and energy storage devices.
4,500원
10.
2024.01
구독 인증기관 무료, 개인회원 유료
The discharge of industrial oily wastewater and oil spill accidents has resulted in significant environmental pollution, creating an urgent need for the treatment of oily wastewater. Nanofiber membranes, known for their high stability, flux, and efficiency, are widely employed in oil–water separation. This study systematically compared the performance of polyacrylonitrile/ graphene oxide (PAN/GO) composite nanofiber membranes prepared through immersion and electrospinning methods for oily wastewater treatment. Experimental findings demonstrated that immersion-prepared membranes achieved high flux (772.9 ± 2.9 L·m−2·h−1, n-hexane/water mixture) and efficiency (98.8%) at a GO concentration of 1.0 g/mL. On the other hand, electrospinning-prepared membranes exhibited superior flux (1500.3 ± 4.4 L·m−2·h−1, n-hexane/water mixture) and efficiency (99.6%) at a higher GO concentration (1.5 g/mL). This membrane displayed excellent stability, maintaining their exceptional performance even after ten cycles of separation. This study compared the advantages and disadvantages of the two methods for preparation of PAN/GO composite nanofiber membrane, offering valuable guidance for practical applications.
4,600원
11.
2024.01
구독 인증기관 무료, 개인회원 유료
This study systematically investigated the efficacy of incorporating graphene/cerium hydroxide (GH) composite material into epoxy-modified polyurethane resin coatings for enhancing the corrosion resistance of Q690qE steel within polluted marine atmospheric conditions. The research encompassed a range of electrochemical assessments and analyses. Notably, the E/GH-0.3% coating displayed a substantially positive open-circuit potential (OCP) and prominently reduced corrosion current density, leading to annual corrosion rates of 2.72 mm/a following 25 days of immersion. Electrochemical impedance spectroscopy (EIS) elucidated the superiority of the E/GH-0.3% coating, characterized by the highest impedance modulus |Z| at 0.1 Hz, indicative of robust corrosion protection. Remarkably, the self-healing performance of E/GH-0.3% and E/ GH-0.5% coatings was evidenced by the formation of a composite passivation layer at scratch sites, particularly pronounced after 40 days of immersion. These findings underscore the promising potential of the GH composite as an effective corrosion inhibitor, holding significant promise for the advancement of protective coatings in harsh coastal industrial environments.
4,000원
12.
2024.01
구독 인증기관 무료, 개인회원 유료
Metals are recognized as electromagnetic interference (EMI) shielding materials owing to their high electrical conductivity. However, the need for light and flexible EMI shielding materials has emerged, owing to the heavyweight and inflexible nature of metals. Carbon nanotube (CNT)/polymer composites have been studied as promising flexible EMI shielding materials because of their lightweight nature due to the low density of CNTs and their high electrical conductivity. CNTs evenly dispersed in the polymer form an electrically conductive network, and the aspect ratio of the CNTs, which are one-dimensional nanofillers, is an important factor affecting electrical conductivity. In this study, we prepared three types of multi-walled carbon nanotubes (MWNTs) with different aspect ratios and fabricated polydimethylsiloxane (PDMS)/MWNT composites. Subsequently, the electrical conductivities and electrical percolation thresholds of the three PDMS/MWNT composites with different MWNT aspect ratios were measured to analyze the behavior of electrically conducting network formation according to the aspect ratio. Furthermore, the total EMI shielding effectiveness of each composite was determined to evaluate the effect of the MWNT aspect ratio on the EMI shielding. Reflection and absorption of electromagnetic wave were measured for the PDMS/MWNT composite with the largest aspect ratio to analyze the EMI shielding mechanism of the composite. Additionally, the effects of the MWNT content on the conductivity and EMI shielding performance were examined. The results provide valuable guidance for designing polymer MWNT composites with good electrical conductivity and EMI shielding performance under different aspect ratios of MWNTs.
4,000원
13.
2024.01
구독 인증기관 무료, 개인회원 유료
Achieving cost-effective and defect-free graphene sheets is highly desirable for sensor devices. Aiming this, few-layer graphene (~ 3) sheets are prepared by an electrochemical exfoliation with [NMP] [ HSO4] electrolyte (i.e., Bronsted acidic ionic liquid). A novel approach for the effective exfoliation of graphene sheets is demonstrated by (i) simultaneously applying a constant potential through an electrochemical cell (with different electrolyte concentrations) and (ii) together with sonication. The exfoliated graphene sheets are characterized through state-of-the-art techniques and sprayed on a glass substrate at optimum conditions. Thus, the transparent conducting sensor device is fabricated with a suitable contact electrode and used for ammonia vapor sensing and the sensor performances are highly dependent on the concentration of the ionic liquid used during the electrochemical exfoliation. The sensing response and limit of detection for the exfoliated graphene-based film were calculated as 3.56% and 432 ppb, respectively. Further studies indicated that the fabricated sensors are more selective towards ammonia molecules with quick response and recovery times.
4,200원
14.
2024.01
구독 인증기관 무료, 개인회원 유료
In recent times, there has been a significant demand for supercapacitors in energy storage applications due to their rapid charging– discharging capabilities, high power density, and excellent stability. Nevertheless, the synthesis of electrode materials with a substantial surface area, exceptionally high porosity, and superior electrochemical performance is still challenging. Activated carbons with a distinctive porous structure and exceptional electrochemical properties emerged as promising electrode materials for supercapacitors. In this study, we used a porous activated carbon (PAC) derived from petroleum coke followed by KOH activation as an efficient anodic electrode material. The ultra-high Brunauer–Emmett–Teller surface area of 2105.6 m2 g− 1 with stacked layers of carbon atoms arranged in a two-dimensional hexagonal structure makes the PAC an efficient candidate for a supercapacitor electrode. The PAC delivers a specific capacitance of 470 F g− 1 at a current density of 0.5 A g− 1 over a potential window of 0 to −1 V. The excellent cycling stability in a three-electrode setup with a capacitance retention of ⁓98% even at a high current density of 10 A g− 1 makes the PAC a potential anodic electrode material for high-performance supercapacitor applications.
4,000원
15.
2024.01
구독 인증기관 무료, 개인회원 유료
Oxygen-rich porous carbon is of great interest for energy storage applications due to its improved local electronic structures compared with unmodified porous carbon. However, a tunable method for the preparation of oxygen-rich porous carbon with a special microstructure is still worth developing. Herein, a novel modification of porous carbon with different microstructures is facilely prepared via low-temperature solvothermal and KOH activation methods that employ the coal tar and eight substances, such as cellulose as carbon source and modifier, respectively. By testing the yield, surface group structure, lattice structures, morphology, thermal weight loss, and specific capacitance of carbonaceous mesophase, cellulose–hydrochloric acid is identified as the additive for the preparation of oxygen-rich coal tar-based porous carbon. The obtained porous carbon displays a specific surface area of up to 859.49 m2 g− 1 and an average pore diameter of 2.39 nm. More importantly, the material delivers a high capacity of 275.95 F g− 1 at 0.3 A g− 1 and maintains a high capacitance of 220 F g− 1 even at 10 A g− 1. When in a neutral electrolyte, it can still retain a reversible capacity of 236.72 F g− 1 at 0.3 A g− 1 and 136.79 F g− 1 at 10 A g− 1. This work may provide insight into the design of carbon anode materials with high specific capacity.
4,500원
16.
2024.01
구독 인증기관 무료, 개인회원 유료
We selected literature from the core collection of the Web of Science (WOS) database as the research object and used visualization bibliometric software to analyse the 1313 collected studies. We found that the research on the graphene-based adsorption of heavy metals from wastewater has received widespread attention in various countries around the world, especially developing countries, since 2015, and Chinese researchers have made significant contributions. The adsorption mechanisms, adsorbent materials, and advanced adsorption techniques for the removal of heavy metals from wastewater by graphene have been the focus and hotspots in the research in this field in recent years. Heavy metal removal from wastewater with graphene has strong application potential. In the future, researchers in this area can focus on exploring issues such as “new materials,” “recyclability,” and “interdisciplinarity” to break through existing technological bottlenecks, supplement the technical research and development of graphene materials, and promote advances in this field.
4,500원
17.
2024.01
구독 인증기관 무료, 개인회원 유료
In this study, a low-cost and easily recyclable porous green adsorbent (magnetic porous loofah biochar, MPLB) was synthesized by modifying the almost zero-cost loofah biochar material with Fe3O4. The successful synthesis of the material was demonstrated by XRD, FTIR, SEM, VSM, and BET. In addition, the material exhibits outstanding magnetic separation performance (40.01 umg/g) allowing for rapid recovery within just 90 s. The adsorption process of phenol on MPLB was found to be spontaneous and endothermic. The experimental data fit exceptionally well with the pseudo-second-order kinetic model and Langmuir model (R2 > 0.99), indicating that the dominant adsorption mechanisms involved monolayer adsorption and chemisorption. These interactions were attributed to host–guest interaction, π–π conjugation, hydrogen bonding, and pore filling. The maximum adsorption capacity calculated using the Langmuir model at 298 K is 39.4 mg/g. Importantly, even after undergoing seven cycles of recycling, MPLB retained 78% of its initial adsorption capacity. In simulated experiments employing MPLB for phenol removal in actual wastewater, an impressive removal rate of 96.4% was achieved. In conclusion, MPLB exhibits significant potential as an effective adsorbent for phenol removal in wastewater.
4,000원
18.
2024.01
구독 인증기관 무료, 개인회원 유료
Muhammad Nawaz, Huma Shaikh, Jamil A. Buledi, Amber R. Solangi, Ceren Karaman, Nevin Erk, Rozhin Darabi, Maria B. Camarada
Environmental pollution has become an alarming issue for the modern world due to the extensive release of untreated chemical waste into freshwater bodies. Untreated chemical waste poses significant negative impacts on aquatic life and human health. The phenolic compounds are widely used in different industries for dyeing, as food preservatives, and for the production of pesticides. 2,4,6-Trichlorophenol (TCP) is among the most hazardous phenolic compounds that cause several serious health effects. Thus, it is important to monitor TCP in the environmental samples frequently. In the current work, it was aimed to develop a highly sensitive zinc oxide-doped (ZnO) reduce graphene oxide (rGO) composite-based electrochemical sensor for TCP monitoring in the real samples. In this regard, graphene oxide (GO) was simultaneously reduced and doped with ZnO using a facile microwave-assisted synthesis strategy. The resulting ZnO/rGO composite was successfully utilized to fabricate ZnO/rGO-modified glassy carbon electrode (ZnO/rGO/GCE) for the selective and trace level determination of TCP. The conductivity and electrocatalytic behaviors of ZnO/rGO/GCE were examined through different modes of electrochemical setup. Under the optimal operating conditions such as a scan rate of 80 mV.s−1, PBS electrolyte (pH 7.0), and the concentration range of 0.01–80 μM, the fabricated electrochemical sensor manifested outstanding responses for monitoring TCP. The limit of detection (LOD) and limit of quantification (LOQ) of the ZnO/rGO/GCE for TCP were found as 0.0067 μM and 0.019 μM, respectively. Moreover, the anti-interference profile and stable nature of ZnO/rGO/GCE made the suggested electrochemical sensor a superb tool for quantifying TCP in a real matrix.
4,600원
19.
2024.01
구독 인증기관 무료, 개인회원 유료
Pitcheri Rosaiah, Ponnusamy Divya, Sangaraju Sambasivam, Ammar M. Tighezza, V. Kalaivani, A. Muthukrishnaraj, Manikandan Ayyar, Theophile Niyitanga, Haekyoung Kim
Synthesis of extremely competent materials is of great interest in addressing the energy storage concerns. Manganese oxide nanowires ( MnO2 NWs) are prepared in situ with multiwall carbon nanotubes (MWCNT) and graphene oxide (GO) using a simple and effective hydrothermal method. Powder XRD, Raman and XPS analysis are utilized to examine the structural characteristics and chemical state of composites. The initial specific discharge capacity of pure MnO2 NWs, MnO2 NWs/ MWCNT and MnO2 NWs/rGO composites are 1225, 1589 and 1685 mAh/g, respectively. The MnO2 NWs/MWCNT and MnO2 NWs/rGO composites showed stable behavior with a specific capacity of 957 and 1108 mAh/g, respectively, after 60 cycles. Moreover, MnO2 NWs/rGO composite sustained a specific capacity of 784 mAh/g, even after 250 cycles at a current density of 1 A/g showing outstanding cycling stability.
4,200원
20.
2024.01
구독 인증기관 무료, 개인회원 유료
The combination of the two-dimensional (2D) materials g-C3N4 and MXenes in photocatalysis offers several advantages. The g-C3N4 can serve as a visible light-absorbing material, while MXenes can enhance the charge separation and transfer processes leading to improved photocatalytic efficiency. A critical review of 77 already published articles in the field of photocatalytic reactions using g-C3N4 and MXenes, such as hydrogen evolution, the reduction of carbon dioxide, the degradation of organic compounds, the redox reactions of nitrogen, was conducted. For the purpose of greater objectivity, the published results were analysed by non-parametric Mann–Whitney, Kolmogorov–Smirnov, and Mood´s median tests and visualised by box and whisker plots. It was found that MXenes can significantly improve the photocatalytic activity of g-C3N4. Adding other co-catalysts to the MXene/g-C3N4 composites does not bring a significant improvement in the photocatalytic performance. Promising results were obtained especially in the fields of hydrogen evolution and the reduction of carbon dioxide. Since the MXenes are relatively a new class of materials, there is still a big challenge for finding new photocatalytic applications and for the enhancement of existing photocatalytic systems based on g-C3N4, especially in terms of the MXenes and g-C3N4 surface and in the heterojunction engineering.
5,400원
