간행물
Carbon Letters KCI 등재 Carbon letters
- 발행기관 한국탄소학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1976-4251 (Print)2233-4998 (Online)
- 수록기간 2000 ~ 2024
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
Vol.32 No.3 (2022년 5월) 22건
1.
2022.05
구독 인증기관 무료, 개인회원 유료
Graphene, the wonder material has brought a revolutionary change in the field of nanotechnology owing to its tremendous properties. Though different methods for the synthesis of graphene have been reported, the chemical synthesis route offers a scalable and high-volume production of graphene. The unreliability of graphite and hydrocarbon resources to serve as steady supplies of carbon resources and further in the synthesis of graphene has led to the exploration and use of alternative low-cost carbon-rich resources (coal, graphite, rice husk, sugarcane bagasse, peanut shells, waste tyres, etc.) as precursors for graphene synthesis. The use of untraditional carbon resources reduces dependence on traditional resources (coal, graphite), reduced cost, increased reliability, and provides a way for the management of waste biomass. This review hence focuses on the synthesis of graphene by the most common approachable method, oxidation–reduction of graphite, along with the various other chemical methods of synthesis from varied carbon resources.
5,100원
2.
2022.05
구독 인증기관 무료, 개인회원 유료
Fluorescent carbon nano-materials with quantum confinement and edge effects have recently piqued attention in a variety of applications, including biological imaging, drug delivery, optoelectronics and sensing. These nano-materials can be synthesized from a variety of carbon-based precursors using both top-down and bottom-up methods. Coal and its derivatives typically include a vast crystalline network and condensed aromatic ring cluster, which can be easily exfoliated by chemical, electrochemical, or physical processes to produce nano-materials. As a result, they are regarded as a low-cost, abundant and efficient carbon source for the fabrication of high-yield nano-materials. Nano-materials synthesized from coal-based precursors have outstanding fluorescence, photostability, biocompatibility and low toxicity, among other properties. Their properties in optical sensors, LED devices, bio-imaging, and photo and electro-catalyst applications have already been investigated. In this review, we have highlighted current developments in the synthesis, structural properties and fluorescence properties of nano-materials synthesized from coal-based precursors.
7,800원
3.
2022.05
구독 인증기관 무료, 개인회원 유료
Graphitic carbon nitride ( C3N4) has been intensively studied in the last 25 years. Although the number of papers about C3N4 published per year has been growing exponentially, there are still some unclear issues with this material. One of them is s-triazine C3N4 (s-C3N4), which is an allotrope of C3N4. The theoretical computational as well as experimental synthetic results are not unambiguous. The properties of s-C3N4 have been described only in two papers, and no similar and reproducible results have been obtained so far. This paper provides a brief overview of s-C3N4 to bring attention to this material, for example, as a potential photocatalyst.
4,000원
4.
2022.05
구독 인증기관 무료, 개인회원 유료
This article presents recent advancements in the development of flexible piezoresistive strain sensors based on carbon nanotubes (CNTs)–polymer composites, with particular attention to their electromechanical properties. Various fabrication approaches and material preparation of CNTs–polymer composites with improved piezoresistive performance are introduced. Moreover, the article presents the working principle of the piezoresistive sensors in terms of the tunneling effect and disconnection-reconnection mechanism. The sensing performances of recently reported applications are studied. This work also reveals that the CNTs–polymer composites have great potential for flexible, skin-mountable, and wearable electronics applications. Finally, possible challenges for the future developments of CNTs–polymer composites are discussed.
4,600원
5.
2022.05
구독 인증기관 무료, 개인회원 유료
Rapid development of carbon nanotubes (CNTs) reinforced to polymer composites has been recently noticed in many aspects. In this work, the latest developments on fatigue and fracture enhancement of polymer composites with CNTs reinforcement with diverse methods are thoroughly compiled and systematically reviewed. The existing available researches clearly demonstrate that fatigue fracture resistance of polymer composites can be improved accordingly with the addition of CNTs. However, this work identifies an interesting research gap for the first time in this field. Based on the systematic reviewing approach, it is noticed that all previously performed experiments in this field were mostly focused upon studying one factor only at a time. In addition, it is also addressed that there were no previous studies reported a relationship or effect of one factor upon others during examining the fatigue fracture of carbon nanotubes. Moreover, there was no adequate discussion demonstrating the interaction of parameters or the influence of one parameter upon another when both were examined simultaneously. It is also realized that the scope of the conducted fatigue fracture studies of carbon nanotubes were mainly focused on microscale fatigue analysis but not the macroscale one, which can consider the effect of environment and service condition. In addition, the inadequacy of fatigue life predicting models via analytical and numerical methods for CNT-reinforced polymer composites have also been highlighted. Besides, barriers and challenges for future directions on the application of CNT-reinforced polymer composite materials are also discussed here in details.
4,600원
6.
2022.05
구독 인증기관 무료, 개인회원 유료
Lipeng Wang, Zongxu Yao, Zhimin Guo, Xiaofeng Shen, Zhiang Li, Zhengqi Zhou, Yuling Wang, Jian‑Guo Yang
Coal-based graphite has become the main material of emerging industries. The microstructure of coal-based graphite plays an important role in its applications in many fields. In this paper, the effect of carbon disulfide/N-methyl-2-pyrrolidone solvent mixture extraction on the microstructure of bituminous coal-based graphite was systematically studied through preliminary extraction coupled with high-temperature graphitization. The graphitization degree g (75.65%) of the coal residue-based graphite was significantly higher than that of the raw coal-based graphite. The crystallite size La of the coal residue-based graphite was reduced by 47.06% compared with the raw coal-based graphite. The ID/ IG value of the coal residue-based graphite is smaller than that of the raw coal-based graphite. The specific surface area (16.72 m2/ g) and total pore volume (0.0567 m3/ g) of the coal residue-based graphite are increased in varying degrees compared with the raw coal-based graphite. This study found a carbon source that can be used to prepare coal-based graphite with high graphitization degree. The results are expected to provide a theoretical basis for further clean and efficient utilization of the coal residue resources.
4,000원
7.
2022.05
구독 인증기관·개인회원 무료
Correction to: Effects of solvent extraction on the microstructure of bituminous coal‑based graphite
Lipeng Wang, Zongxu Yao, Zhimin Guo, Xiaofeng Shen, Zhiang Li, Zhengqi Zhou, Yuling Wang, Jian‑Guo Yang
8.
2022.05
구독 인증기관 무료, 개인회원 유료
NiMoS2 is a promising material for various functional applications and highly compatible with GO to make hybrid nanocomposites with excellent characteristics for supercapacitor electrode material. Deposition of NiMoS2 was achieved on the rGO(reduced Graphene Oxide) surface to form a NiMoS2− rGO nanocomposite by the method of the facile hydrothermal synthesis process. XRD pattern shows the crystalline nature of composites. Raman and EPMA result interpreting the composites formation and elements compositions, respectively. The sheet-like morphology of rGO was found in the composites by FESEM images. Particles distribution was confirmed by HR-TEM. The electrochemical properties of the pure NiMoS2 and NiMoS2– rGO composites have been studied by cyclic voltammetry analysis. The results revealed that the NiMoS2/ 5% rGO nanocomposites exhibit high specific capacitance compared to pure NiMoS2 due to the synergistic effects of NiMoS2 and rGO in the composite material. The photocatalytic behavior of the prepared nanocomposites for dye degradation was tested. The quantity of rGO has significantly improved the photocatalytic behavior of NiMoS2/ rGO composites. The studies on degradation mechanism, the N2 adsorption/desorption isotherms, pore size distribution behavior and % of removal of MB reveal the enhanced photocatalytic performance of sysnthesised composites.
4,500원
9.
2022.05
구독 인증기관 무료, 개인회원 유료
The main objective of the research was to deposit thin films of silver on a graphite carbon paste in a phosphate buffer medium using an electrochemical method. To construct a nitrofurazone detection sensor that is highly sensitive. Different manufacturing parameters, such as electrodeposition potential, pH effect, potential scan rate effect, and number of scan cycles, were examined in this section. The parameters were optimized to improve the deposited silver layers various electrocatalytic characteristics. The Nitrofurazone reduction process is diffusion controlled, as seen by the linear variation of Epc with log(v). The constructed Ag-NPs@CPE electrod has excellent electrical characteristics a large active surface area and low background with extremely high electrical conductivity, according to structural and electrochemical characterizations such as Scanning electron microscopy, X-ray diffraction (XRD) and cyclic voltammetry. The constructed sensor has a very remarkable analytical performance for nitrofurazone molecule identification, with a very low detection limit of about 10– 8 M. The detection of nitrofurazone using our Ag-NPs@CPE sensors in real samples contaminated with the antibiotic nitrofurazone, such as tap water and urine. In the selected sample, the electroanalytical findings reveal a very satisfactory recovery rate of more than 94 percent.
4,600원
10.
2022.05
구독 인증기관 무료, 개인회원 유료
Large-area graphene of the order of centimeters was deposited on copper substrates by low-pressure chemical vapor deposition (LPCVD) using hexane as the carbon source. The effect of temperature and the carrier gas flowrates on the quality and uniformity of the as-deposited graphene was investigated using the Raman analysis. The film deposited at 870 °C with a total carrier gas flowrate of 50 sccm is predominantly single-layer with very low defects according to the Raman spectra. The 2D/G peak intensity ratios obtained from the Raman spectra of samples from three different locations of graphene deposited on a whole copper catalyst was used to calculate the large-area uniformity. Based on the results, a very high uniformity of 89.6% was calculated for the graphene deposited at 870 °C. The uniformity was observed to decrease with increasing temperature. Similar to the thickness uniformity, the electrical conductivity values obtained as a result of I–V measurements and water contact angle measurements were found to be close to each other for the graphene deposited under the same deposition conditions.
4,000원
11.
2022.05
구독 인증기관 무료, 개인회원 유료
To thoroughly analyze the mechanical properties and surface conditions of HF50S carbon fibers, the tensile properties, surface morphology, surface chemical element, surface energy, sizing agent properties, and Naval Ordnance Laboratory (NOL) ring of their composites were characterized. Furthermore, the aforementioned properties were exhaustively compared with those of T1000G carbon fibers. The results showed that the tensile strength, modulus, and elongation of the HF50S carbon fibers were 6638 MPa, 297 GPa, and 2.2%, respectively, thus demonstrating that the mechanical properties of the HF50S carbon fibers were on par with those of the T1000G carbon fibers, in addition, the coefficient of variation (Cv) indices of HF50S carbon fiber were below 3%, indicating good stability. The HF50S carbon fibers have a smooth surface without grooves, which is analogous to that of the T1000G carbon fibers prepared by the typical dry jet–wet spinning process. The main component of the sizing agent of the HF50S carbon fibers is an epoxy resin, which is also used for the preparation of epoxy matrix composites. Because the HF50S carbon fiber surface has greater O and N contents than the T1000G carbon fiber surface, the HF50S carbon fibers have more active functional groups and higher surface activity. The surface energy of the HF50S carbon fibers is 30.13 mJ/m2, which is higher than that of the T1000G carbon fibers (28.42 mJ/m2). Owing to the higher strength and surface activity of the HF50S carbon fibers than those of the T1000G carbon fibers, the strength and strength conversion of NOL ring based on the former are slightly higher than those of that prepared using the latter.
4,000원
12.
2022.05
구독 인증기관 무료, 개인회원 유료
Two kinds of mesocarbon microbeads (MCMBs) with different chemical composition have been synthesized. The MCMBs were molded and heat treated at temperatures above 2000 °C to obtain graphite blocks. The effects of chemical composition of MCMBs on the pore morphology, carbon texture and thermal properties of the derived graphite blocks have been explored. The pore morphology was investigated by small angle X-ray scattering technique and a graphitization-induced morphology transition was observed. When the graphitic crystallite size exceeded a threshold value, the association of crystallites and migration of randomly distributed pores took place extensively. For the graphite blocks made of MCMBs which had light components with higher aromaticity value, the growth of crystallites caused a significant enhancement in thermal conductivity for the specimens. However, for the other kind of MCMBs, their light components tended to form solid porous carbon texture after graphitization, and the thermal conductivity coefficients of their graphite blocks could only increase slightly as crystallites grew. It was suggested that the thermal resistance at the granule’s boundary became noticeable in the latter case and thus the growth of thermal conductivity coefficients was prominently hindered.
4,000원
13.
2022.05
구독 인증기관 무료, 개인회원 유료
Hui Ning, Zhihao Guo, Wenhang Wang, Xiaoshan Wang, Zhongxue Yang, Zhengguang Ma, Yangming Tian, Chenghao Wu, Jian Hao, Mingbo Wu
Electrochemical reduction of carbon dioxide to valuable chemicals is a promising way of storing renewable energy through electric-to-chemical energy conversion, while its large-scale application is in urgent need of cheap and high-performance catalysts. Herein, we invent a convenient method to synthesize N-doped porous carbon by ammonia etching the pyrolysis carbon of petroleum pitch. We found the ammonia etching treatment not only increase the pyridinic-N content, but also enlarge the specific surface area of the petroleum pitch-based porous carbon. As a cheap and easily available catalyst for carbon dioxide electroreduction, up to 82% of Faradaic efficiency towards carbon monoxide was obtained at − 0.9 V vs the reversible hydrogen electrode in 0.1 M KHCO3. After a long time electrocatalysis of more than 20 h, the Faradaic efficiency of carbon monoxide remains 80%, indicating the porous carbon as made have an ultra-high stability as catalyst for carbon dioxide reduction. Our work provides a new technology to economically prepare efficient electrocatalysts for carbon dioxide reduction.
4,000원
14.
2022.05
구독 인증기관 무료, 개인회원 유료
In this present investigation, machinability studies on novel aluminum composite with hybrid reinforcements of copper-coated 4% carbon fibers (CFs) and 3% nanoclay in AA6026 matrix fabricated by compocasting method is performed. Step drill bit and multifaceted drill bit are used by adopting central composite design (CCD) in response surface methodology (RSM). The outcomes show that, with a rise in rotational speed surface irregularities, resultant force and material removal rate (MRR) intensifies, and with the additional rise in rotational speed, all the outputs decrease considerably. High MRR, resultant cutting force, and surface roughness are obtained with multifaceted carbide drills, compared with a step drill. Desirability function is used to maximize the MRR and minimize the resultant cutting forces considering the constant surface roughness of 3 μm. The optimal values are rotational speed of 1285 rpm, feed rate of 60 mm/min with the step drill bit, producing an MRR of 0.0439 kg/sec and a resultant cutting force of 185.818 N. The second-order empirical models are developed for outputs, which are fed into the non-traditional metaheuristic Evaporation Rate-based Water Cycle Algorithm (ER-WCA) therefore the lower objective value is achieved with step drill of 51.7421. It is found that using a step drill the machinability performance of this hybrid nanocomposite is well improved than the machining with other drill bits. This composite fulfills the norms of 2000/53/CE-ELV European environmental directives.
5,400원
15.
2022.05
구독 인증기관 무료, 개인회원 유료
Abstract In the present study, the effect of nickel nitrate addition as a catalytic precursor for the in situ formation of Ni nanoparticles during the heating process has been investigated on the modification of microstructure and graphitization of amorphous carbon resulting from pyrolysis of phenolic resin. For this purpose, the prepared resin samples were cured in carbon substrate with and without additives at temperatures of 800, 1000, and 1250 °C. XRD, FESEM, and TEM studies were performed to investigate the phase and microstructural changes in the samples during the heating process. In addition to phase and microstructural studies, thermodynamic calculations of the reactions performed for the in situ formation of nickel nanoparticles and their effective factors during the curing process were performed. The results indicated that nickel nitrate is transformed to nickel nanoparticles of different sizes during the reduction process in a reduced atmosphere. The in situ formation of nickel nanoparticles and its catalytic effect led to the graphitization of carbon resulting from the pyrolysis of phenolic resin at a temperature of 800 °C and above. By increasing temperature, the morphology of the formed graphite changed and hollow carbon nanotubes, carbon cells, and onion skin carbon were formed in the microstructure. It was also observed that by increasing the temperature and the amount of additive, carbon nanotubes and their size are increased. A noteworthy point from thermodynamic calculations during the formation of nickel nanoparticles was that the nickel nanoparticles themselves acted as accelerators of nickel oxide reduction reactions and the formation of nickel nanoparticles. This increases the amount of amorphous carbon graphitization resulting from the pyrolysis of phenolic resin which leads to the formation of more carbon nanotubes at higher temperatures.
4,600원
16.
2022.05
구독 인증기관 무료, 개인회원 유료
Hypercrosslinked polymers HCPs have been widely used as precursors to prepare porous carbon materials because of their highly ordered porous structure and large specific surface area. In this paper, we used a solvothermal method to prepare a hypercrosslinked polymer, and the HCPC-700-A was prepared using an activation method with the hypercrosslinked polymer as the precursor. The effects of different carbon–alkali ratios on the microstructure, composition and electrochemical properties of porous carbon HCP were studied. The results show that the surface of porous carbon HCPC-700-A presents a relatively regular geometric shape, and a large number of pore structures are mainly micro- and mesopores. The specific surface area is 2074.53 m2 g− 1, and the average pore size is between 1.29 and 1.93 nm. Porous carbon HCPC-700-1:2 has excellent electrochemical performance in 1 M H2SO4, and the specific capacitance is up to 464.4 F g− 1 at a current density of 1 A g− 1. The specific capacitance decay rate is 29.72% when the current density is increased from 1 A g− 1 to 8 A g− 1. After 5000 cycles, the capacitance retention rate is 91.16% at a current density of 2 A g− 1, showing excellent electrochemical performance, good cycle stability and perfect energy storage performance. This research provides new experimental ideas for HCPs in the electrochemical energy storage field.
4,600원
17.
2022.05
구독 인증기관 무료, 개인회원 유료
In view of the activated carbon pore-forming mechanism, the fractal hypothesis of pore interior growth was proposed by optimizing the structure of Sierpinski sponge. Based on the hypothesis and the definition of fractal dimension, the function relationship between the reaction degree, reaction step length, specific surface area and pore volume was deduced, and the pore fractal growth model of activated carbon activation process was established. Semi-coke, apple charcoal and lychee charcoal were used to prepare activated carbon. The pore size distributions of the activated carbons are in accordance with the fractal growth hypothesis. Further, the reaction degree and reaction step length can be determined by the experimental data of pore and surface structure, which verified the feasibility of the pore fractal growth model.
4,200원
18.
2022.05
구독 인증기관 무료, 개인회원 유료
A porous-carbon material UiO-66-C was prepared from metal–organic frameworks UiO-66 by carbonization in inert gas atmosphere. Physicochemical properties of UiO-66-C materials were well characterized by Powder X-ray diffraction (PXRD), Scanning electron microscope (SEM), Fourier-transform infrared spectroscopy (FT-IR), Raman spectrometer, N2 adsorption/ desorption isotherms (BET), and the adsorption properties of the products were studied UiO-66-C has a high specific surface area up to 1974.17 m2/ g. Besides, the adsorption capacity of tetracycline could reach 678.19 mg/g, the adsorption processes agreed well with the pseudo-second-order kinetic model and Langmuir isotherm model.
4,000원
19.
2022.05
구독 인증기관 무료, 개인회원 유료
Electrochemical water splitting is an important process for next generation of eco-friendly energy systems. The oxygen evolution reaction (OER), which occurs at an anode during the process, requires efficient electrocatalysts to reduce activation energies. Although Ru- or Ir-containing materials show excellent electrocatalytic activities, their high cost is a critical drawback. Consequently, the development of efficient electrocatalysts composed of low-cost metal components is a great challenge. In this study, we develop a new route to produce a hybrid material (Fe–NC) containing Fe3C particles dispersed on the surface of N-doped carbon (NC) materials by heat treatment of a mixture of urea and Fe(II)Cl2(H2O)4. Microscopic analyses prove that the Fe3C particles are placed on the surfaces of thin NC materials. Additionally, various characterizations reveal that the particles contain Fe3C structure. Fe–NC shows good electrocatalytic properties with onset and overpotentials of 1.57 V and 545 mV, respectively, for OER in KOH electrolyte. This study suggests the possibility of the use of Fe3C- based composites as OER electrocatalysts.
4,000원
20.
2022.05
구독 인증기관 무료, 개인회원 유료
Organic reagent is considered as one of the most promising reductants for deeply removing vanadium (V) trichloride oxide ( VOCl3) from crude titanium tetrachloride ( TiCl4). Nevertheless, indeterminate active component and unclearly removal mechanisms appear to be the obstacles to separate VOCl3 from TiCl4 using organic reagent. Herein we conduct the experiment to explore it. Firstly, the organic reagents are obtained from enterprise (noted as EOR1– EOR7), and then it is determined that carbon aromatic ( CA) is the active component for removing VOCl3. Furthermore, modified organic reagents (noted as MOR1– MOR4) are prepared via adding aromatic hydrocarbon oil and stearic acid to EOR7, then indicating that MOR3 is endowed with the best capacity to remove VOCl3. In addition, the residues obtained from distillation experiment are comprehensively analyzed (using X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM) etc.), revealing that porous amorphous carbon that deriving from MOR, plays an excellent role in removing VOCl3 from TiCl4 system. Therefore, the removal mechanisms can be explained like that porous amorphous carbon reduces VOCl3 into insoluble vanadium (III) chloride ( VCl3) and vanadium (IV) oxide dichloride ( VOCl2), and then they are separated via adsorption process, with the help of porous amorphous carbon.
4,500원
1
2
