간행물
Carbon Letters KCI 등재 Carbon letters
- 발행기관 한국탄소학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1976-4251 (Print)2233-4998 (Online)
- 수록기간 2000 ~ 2023
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
Vol.33 No.7 (2023년 12월) 38건
1.
2023.12
구독 인증기관 무료, 개인회원 유료
A thermochemical conversion method known as hydrothermal carbonization (HTC) is appealing, because it may convert wet biomass directly into energy and chemicals without the need for pre-drying. The hydrochar solid product’s capacity to prepare precursors of activated carbon has attracted attention. HTC has been utilized to solve practical issues and produce desired carbonaceous products on a variety of generated wastes, including municipal solid waste, algae, and sludge in addition to the typically lignocellulose biomass used as sustainable feedstock. This study aims to assess the in-depth description of hydrothermal carbonization, highlighting the most recent findings with regard to the technological mechanisms and practical advantages. The process parameters, which include temperature, water content, pH, and retention time, determine the characteristics of the final products. The right setting of parameters is crucial, since it significantly affects the characteristics of hydrothermal products and opens up a range of opportunities for their use in multiple sectors. Findings reveal that the type of precursor, retention time, and temperature at which the reaction is processed were discovered to be the main determinants of the HTC process. Lower solid products are produced at higher temperatures; the carbon concentration rises, while the hydrogen and oxygen content declines. Current knowledge gaps, fresh views, and associated recommendations were offered to fully use the HTC technique's enormous potential and to provide hydrochar with additional useful applications in the future.
6,300원
2.
2023.12
구독 인증기관 무료, 개인회원 유료
The widespread and extensive use of glyphosate in agriculture has raised concerns about its potential impact on the quality and safety of agricultural products. Conventional detection methods require long analysis times, making them impractical for the rapid detection of large quantities of samples. Therefore, developing a fast and simple detection system for glyphosate pesticide residues is urgent. In this study, the development of a facile fluorescence probe synthesized using a simple one-pot hydrothermal method for the determination of glyphosate is an important step toward addressing the need for a fast and simple detection system. The present sensor was created using bovine serum albumin (BSA) as a precursor, and the sensor operates by producing an “off–on” fluorescent signal. The bovine albumin-derived BSA-CDs emitted light yellow fluorescence, but this fluorescence was quenched (or suppressed) by the presence of Cu2+ ions. However, the fluorescence can be restored by the presence of glyphosate, which interacts with the Cu2+ ions to form a complex and release the BSACDs from suppression. The functional groups in glyphosate can capture Cu2+ and break the BSA-CDs/Cu2+ combinatorial system. The BSA-CDs/Cu2+ fluorescence quenching system had good selectivity for glyphosate. The detection limit of the BSA-CD/Cu2+ fluorescence sensor was 0.05 μg/mL. This developed method was utilized to successfully detect glyphosate in Chinese wheat. The average recoveries ranged from 98.9 to 100.7%, with a relative standard deviation < 3.0%, showing good prospects for practical applicability.
4,200원
3.
2023.12
구독 인증기관 무료, 개인회원 유료
Organic wastewater causes serious environmental pollution, and catalytic oxidation is promising technique for wastewater treatment. Developing green and effective catalysts is currently challenging. In this work, green synthesis of nano zerovalent iron loaded onto porous biochar derived from popcorn is conducted, and catalytic oxidation of Rhodamine B (RhB) is evaluated in the presence of H2O2. Effect of process factors is examined on catalytic performance for RhB removal. The mechanism of RhB removal is discussed by characterizations (Fourier transform infrared spectra and Raman) and UV–vis spectra. RhB removal is improved with high catalyst dosage, low initial RhB concentration, and high reaction temperature, while it is slightly influenced by carbonization temperature of biochar, H2O2 dosage and pH value. Under conditions of BC-250 1.0 g/L, H2O2 0.01 mol/L, pH 6.1, and temperature 30 °C, the removal rate of RhB is 92.27% at 50 min. Pseudo first-order kinetics is used to fitting experimental data, and the activation energy for RhB removal in BC-250/H2O2 system is 39 kJ/mol. RhB removal in BC-250/H2O2 system can be attributed to adsorption effect and catalytic oxidation with the dominant role of hydroxyl radical. This work gives insights into catalytic oxidation of organic wastewater using green catalyst.
4,200원
4.
2023.12
구독 인증기관 무료, 개인회원 유료
In this study, we synthesized a reduced graphene oxide-manganese dioxide (rGO-MnO2) composite material using a one-step hydrothermal method and used it as a transducer layer in solid-state ion-selective electrodes (ISEs) for monitoring potassium and sodium ions in sweat. The rGO-MnO2 composite was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), revealing its unique surface morphology and crystalline structures. Electrochemical characterizations, including cyclic voltammetry (CV) and potential response testing, demonstrated the excellent performance of the rGO-MnO2 composite material as a transducer layer in ISEs. The fabricated electrodes displayed good linear responses to potassium and sodium ions, with a voltage response of 36.4 mV and 47.6 mV per unit concentration change, respectively. The electrodes also exhibited improved resistance to gas interference, such as O2, N2, and CO2. We utilized these ISEs to measure changes in potassium and sodium ion concentrations in sweat samples collected over nine days of exercise, demonstrating the practical application of the rGO-MnO2-based ISEs. This work highlights the potential of using graphene/metal oxide composites as solid contact materials in ISEs for cost-effective and stable ion sensing applications.
4,000원
5.
2023.12
구독 인증기관 무료, 개인회원 유료
Energy storage for sustainable development and progress of power production industries is vitally important. The energy storage devices are under extensive research from last three decades to ensure the hand-on-hand coordination with power supply phenomenon and to reduce the energy loses in lines. The cost-effective materials are still highly demanding as an electrode material for energy storage devices. Biomass-derived carbon materials are best candidates due to their low cost, relatively high abundance, pollution-free nature. Here, we are reporting a facile two-step green approach to convert Himalayan horse chestnuts (HHCNs) into activated carbon materials. In first step, grinding and pyrolysis of the HHCNs were carried out, and then activation was performed using KOH to enhance the pore density and surface area. HHCNs-derived carbon was utilized as an electrode in electrical double-layer capacitors (EDLCs) with 1 M H2SO4 as an electrolyte. The macroporous structure along with hierarchical porous network acts as an efficient source of transportation of charges across the electrode and separator. Cyclic voltammetry test was taken from 10 to 100 mV/s current and within a range of 0–1 V applied potential; approximately rectangular CV shown mirror response towards current and shown typical EDLCs properties. The proximate analysis confirms the presence of heteroatoms like sulfur, oxygen, and nitrogen which act as carbon dopants. The wettability of HHCNs-derived carbon enhanced due to the various types of oxygen functionalities inherited from the lignin skeletal part. The nitrogen content is primarily responsible for the pseudo-capacitive behavior of HHCNs-codoped carbon. HHCNs-derived activated carbon materials has emerged as a promising electrode material for energy storage applications.
4,000원
6.
2023.12
구독 인증기관 무료, 개인회원 유료
Modification of the surface of raw activated carbon using chemical solvents can significantly improve the adsorption performance of activated carbon. Triethylenetetramine is one of the most important chemical solvents used to modify raw activated carbon for formaldehyde removal indoor. We conducted the liquid impregnation experiments at different initial concentrations, temperatures, adsorbent dosage and time ranges to fully investigate the adsorption of triethylenetetramine on the surface of raw activated carbon for modification. We found that the Langmuir isotherm model and pseudo-first-order kinetic model fit quite well with the experimental data and the R2 are 0.9883 and 0.9954, respectively. The theoretical maximum adsorption capacity is 166.67 mg/g. The change in Gibbs free energy (ΔG0), enthalpy change (ΔH0) and entropy change (ΔS0) were also calculated to study the direction and driving force of the liquid adsorption process. In order to understand the adsorption process at the molecular level, a new activated carbon model based on the actual physical and chemical properties of activated carbon was carefully established in the Materials Studio to simulate the liquid-phase adsorption. The pore structure, elemental composition, functional group content, density, pore volume, and porosity of the activated carbon model converge close to the actual activated carbon and the adsorption isotherms obtained from the simulation agree well with the experimental results. The results show that the adsorption of triethylenetetramine on activated carbon is a spontaneous, endothermic and monolayer physical adsorption process.
4,800원
7.
2023.12
구독 인증기관 무료, 개인회원 유료
Merve Akin, Ramazan Bayat, Muhammed Bekmezci, Zeynep Kazel Coguplugil, Fatih Sen, Mehdi Baghayeri, Afsaneh Kaffash, Fatemah Tehranejad‑Javazmi, Iran Sheikhshoaie
In this research, reduced graphene oxide/polypyrrole (rGO/PPy) particles were synthesized and used to measure the amount of dopamine (DA) electrochemically. The obtained rGO/PPy particle was characterized by Fourier Transform Infrared Spectrophotometer (FTIR), UV–Visible Spectrophotometer (UV–Vis), and X-Ray Diffraction Diffractometry (XRD). To investigate the DA sensor performance, cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to acquire electrochemical measurements of the sensor. Current values of 1.65 and 5.9 mA were observed in the CV at 0.2 mM and 1.2 mM concentrations of target molecule, respectively. Under optimized conditions, the linear calibration plots were found to exhibit significant sensitivity in the linear range of 0.2 and 1.2 mM, with a corresponding detection limit of 0.061 μM for DA. The results obtained were similar to the sensor results of DA made using precious metals. This work was a demonstration of the feasibility of high-sensitivity electrochemical analysis with conductive carbon materials without the use of precious metals. It was also observed that the cost-effective rGO/PPy exhibited a very high potential for DA detection.
4,000원
8.
2023.12
구독 인증기관 무료, 개인회원 유료
Kai Chen, Tao Tao, Wenxiao Hu, Yucong Ye, Kaiwen Zheng, Jiandong Ye, Ting Zhi, Xiwei Wang, Bin Liu, Rong Zhang
High-quality diamond films have attracted extensive attentions due to their excellent optical and electrical properties. However, several issues, such as random orientation, stress accumulation, and slow growth rate, severely limit its applications. In this paper, high-quality polycrystalline diamond films with highly ordered (100) orientation were prepared by microwave plasma chemical vapor deposition. The effects of growth parameters on the microstructure, quality and residual stress of diamond films were investigated. Experimental results indicate that relatively high temperature at low methane concentration will promote the formation of (100) oriented grains with a low compressive stress. Optimized growth parameters, a methane concentration of 2% along with a pressure of 250 Torr and temperature at 1050 ℃, were used to acquire high growth rate of 7.9 μm/h and narrow full width at half maximum of Raman peak of 5.5 cm− 1 revealing a high crystal quality. It demonstrates a promising method for rapid growth of high-quality polycrystalline diamond films with (100) orientation, which is vital for improving the diamond related applications at low cost.
4,000원
9.
2023.12
구독 인증기관 무료, 개인회원 유료
E. Gomathi, P. Maharaja, Hanumant Singh Rathore, R. Boopathy, Rames C. Panda, T. Senthilvelan, Maruthapillai Arthanareeswari
The dyeing process is a very important unit operation in the leather and textile industries; it produces significant amounts of waste effluent containing dyes and poses a substantial threat to the environment. Therefore, degradation of the industrial dye-waste liquid is necessary before its release into the environment. The current is focusing on the reduction of pollutant loads in industrial wastewater through remediating azo and thiazine dyes (synthetic solutions of textile dye consortium). The current research work is focused on the degradation of dye consortium through photo-electro-Fenton (PEF) processes via using dimensionally stable anode (Ti) and graphite cathode. The ideal conditions, which included a pH of 3, 0.1 (g/L) of textile dye consortium, 0.03 (g/L) of iron, 0.2 (g/L) of H2O2, and a 0.3 mAcm-2 of current density, were achieved to the removal of dye consortium over 40 min. The highest dye removal rate was discovered to be 96%. The transition of azo linkages into N2 or NH3 was confirmed by Fourier transforms infra-red spectroscopic analysis. PEF process reduced the 92% of chemical oxygen demand (COD) of textile dye consortium solution, and it meets the kinetics study of the pseudo-first-order. The degradation of dye through the PEF process was evaluated by using the cyclic voltammetric method. The toxicity tests showed that with the treated dye solution, seedlings grew well.
4,800원
10.
2023.12
구독 인증기관·개인회원 무료
M. M. Atta, Hesham M. H. Zakaly, N. Almousa, A. M. Abdel Reheem, M. Madani, Usama.F. Kandil, A. M. A. Henaish, Eman O. Taha
11.
2023.12
구독 인증기관 무료, 개인회원 유료
An environmentally friendly and low-cost chitosan-containing polysaccharide (CP) composite ZIF-8/CP was designed and prepared based on the difficulty of separating the traditional adsorbent from the water phase. ZIF-8/CP was synthesized through in-situ growth approach. The physical, chemical and structure properties of ZIF-8/CP were determined through a series of characterization methods, including SEM, FT-IR and PXRD. The effects of touch time, pH, temperature, and coexisting ions on adsorption were assessed. In addition, kinetics, isotherms of adsorption and thermodynamics were examined. The data of isotherms for adsorption indicated that the adsorption of ZIF-8/CP on MG was similar to the Langmuir model, with a maximum adsorption capacity of 1428.57 mg/g. Moreover, the kinetic parameters were consistent with the pseudo- 2nd-order equation. Thermodynamic studies (ΔG < 0, ΔH > 0) demonstrated a heat-absorbing and spontaneous adsorption process. Our study reveals that ZIF-8/CP has good adsorption properties and environmental properties.
4,200원
12.
2023.12
구독 인증기관 무료, 개인회원 유료
Semiconductor-based photocatalytic carbon dioxide ( CO2) reduction is of great scientific importance in the field of alleviating global warming and energy crisis. Surface amine modification and cocatalyst loading on the catalyst surface could improve CO2 adsorption capacity and photogenerated charge separation. Herein, amine-modified brookite–TiO2 ( NH2–B–TiO2) coupled metal species (Cu, Ag, Ni(OH)2) cocatalysts have been successfully synthesized by chemical reduction method. The photocatalytic CO2 reduction results show that the CH4 production rates of NH2– B–TiO2/Cu, NH2– B–TiO2/Ag, and NH2– B–TiO2/Ni(OH)2 are 3.2, 12.5, and 1.7 times that of NH2– B–TiO2 (0.74 μmmol g− 1 h− 1), respectively. Results show the introduction of metal species on the surface of the catalyst enhances the absorption range of sunlight and the photogenerated carrier separation efficiency, resulting in enhancing the performance of photocatalytic CO2 reduction. This work provides a strategy for designing metal species-loaded amine-modified brookite–TiO2 by surface/interface regulation to improve photocatalytic efficiency.
4,200원
13.
2023.12
구독 인증기관 무료, 개인회원 유료
To improve the thermophysical properties of Al alloy for thermal management materials, the Cu-coated carbon fibers (CFs) were used as reinforcement to improve the thermal conductivity (TC) and the coefficient of thermal expansion (CTE) of Al-12Si. The CFs reinforced Al matrix (CFs/Al) composites with different CFs contents were prepared by stir casting. The effects of the CFs volume fraction and Cu coating on the microstructure, component, TC and CTE of CFs/Al composites were investigated by scanning electron microscopy with EDS, X-ray diffraction, thermal dilatometer and thermal dilatometer. The results show that the Cu coating can effectively improve the interface between CFs and the Al-12Si matrix, and the Cu coating becomes Al2Cu with Al matrix after stir casting. The CFs/Al composites have a relative density greater than 95% when the volume fraction of CFs is less than 8% because the CFs uniform dispersion without agglomeration in the matrix can be achieved by stir casting. The TC and CTE of CFs/Al composites are further improved with the increased CFs volume fraction, respectively. When the volume fraction of CFs is 8%, the CFs/Al composite has the best thermophysical properties; the TC is 169.25 W/mK, and the CTE is 15.28 × 10– 6/K. The excellent thermophysical properties of CFs and good interface bonding are the main reasons for improving the thermophysical properties of composites. The research is expected to improve the application of Al matrix composites in heat dissipation neighborhoods and provide certain theoretical foundations.
4,000원
14.
2023.12
구독 인증기관 무료, 개인회원 유료
Seawater evaporation and purification powered by solar energy are considered as a promising approach to alleviate the global freshwater crisis, and the development of photothermal materials with high efficiency is imminent. In this study, cellulose nanofiber (CNF)/MXene/Ni chain (CMN) aerogels were successfully synthesized by electrostatic force and hydrogen bond interaction force. CMN10 achieved a favorable evaporation rate as high as 1.85 kg m− 2 h− 1 in pure water, and the corresponding evaporation efficiency could be up to 96.04%. Even if it is applied to seawater with multiple interference factors, its evaporation rate can still be 1.81 kg m− 2 h− 1. The superior seawater evaporation activity origins from the promoted separation of photoexcited charges and photothermal conversion by the synergy of Ni chain and MXene, as well as the water transport channel supported by the 3D structure frame of CNF. Most importantly, CMN aerogel can maintain water vapor evaporation rates above 1.73 kg m− 2 h− 1 under extreme conditions such as acidic (pH 2) and alkaline (pH 12) conditions. In addition, various major ions, heavy metals and organic pollutants in seawater can be rejected by CMN10 during desalination, and the rejection rates can reach more than 99.69%, ensuring the purity of water resources after treatment. This work shows the great potential of CMN aerogel as a high-efficiency solar evaporator and low-cost photothermal conversion material. Cellulose nanofiber (CNF)/MXene/Ni chain (CMN) aerogels demonstrated high evaporation of water from sea water.
4,300원
15.
2023.12
구독 인증기관 무료, 개인회원 유료
In the present study, an innovative electrochemical sensing platform was established for sensitive detection of NO2 —. This sensor was developed using CoFe alloy encapsulated in nitrogen-doped carbon nanocubes (named as CoFe@NC-NCS), synthesized through the calcination of polydopamine-coated CoFe Prussian-blue analogues (CoFe-PBA@PDA). The morphological and electrochemical characterization reveals that the CoFe@NC-NCS possesses high electrocatalytic activity for electrochemical quantitation of NO2 —, ascribed to the huge surface area and plentiful active positions, benefiting from the porous, hollow, and core–shell structure of CoFe@NC-NCS. Under the optimal conditions, CoFe@NC-NCS/GCE possessed remarkable sensing performance for NO2 — with wide liner ranges and a detection limit of 0.015 μM. NO2 — recovery experiments in real samples exhibited recoveries in the range of 98.8–103.5%. Hence, the CoFe@NC-NCS shows great promise for the construction of electrochemical sensor with more potential application.
4,300원
16.
2023.12
구독 인증기관 무료, 개인회원 유료
Exploring cheap and efficient oxygen evolution reaction (OER) catalysts is extremely vital for the commercial application of advanced energy storage and conversion systems. Herein, a self-supporting Co3S4/ S-doped reduced graphene oxide ( Co3S4/S-rGO) film catalyst is successfully prepared by a blade coating coupled with high-temperature annealing strategy, and its morphology, structure and composition are measured and analyzed. It is substantiated that the as-synthesized Co3S4/ S-rGO film possesses unique self-supporting structure, and is composed of uniformly dispersed Co3S4 nanoparticles and highly conductive S-rGO, which benefit the exposure of catalytic sites and electron transfer. By reason of the synergistic effect of the two individual components, the self-supporting Co3S4/ S-rGO film catalyst displays outstanding catalytic performance towards OER. As a consequence, the Co3S4/ S-rGO film catalyst delivers an overpotential of 341 mV at 10 mA cm-2, and the current attenuation rate is only 2.6% after continuous operation for 4 h, verifying excellent catalytic activity and durability. Clearly, our results offers a good example for the construction of high-performance self-supporting carbon-based composite film catalysts for critical electrocatalytic reactions.
4,000원
17.
2023.12
구독 인증기관 무료, 개인회원 유료
In this research, in order to increase the oxidation resistance of graphite, kaolin and alumina powder with different ratios (26A-74S, 49A-51S, 72A-28S) and slurry method were used to create an aluminosilicate coating on the graphite substrate. In order to reduce the difference in the coefficients of thermal expansion of graphite with aluminosilicate coating, aluminum metaphosphate coating as an interlayer was prepared on the surface of graphite by cathodic electrochemical treatment. The isothermal oxidation test of the samples was carried out in air at a temperature of 1250 °C for 1, 3 and 5 h. The microstructure, chemical composition, and phase components of the coating were, respectively, analyzed by scanning electron microscope equipped with an energy-dispersive spectrometer and X-ray diffraction. The results indicated that, by increasing the withdrawal speed of the samples in slurry method, the amount of changes in the weight of the samples has increased and therefore had a direct effect on oxidation. In addition, it was approved that, at high-temperature oxidation, AlPO4 glass phase forms on aluminum metaphosphate interlayer which retards graphite oxidation. Along with aluminum metaphosphate, aluminosilicate coating also produces a glass phase which fills and seals the voids on the surface which prevents the oxygen to reach the surface of graphite. The created double-layer coating including an interlayer of aluminum metaphosphate + slurry coating prepared with the ratio of 26A-74S as the optimal coating in this research was able to increase the oxidation resistance of graphite by 73% at a temperature of 1250 °C.
4,600원
18.
2023.12
구독 인증기관 무료, 개인회원 유료
A simple and one-pot synthetic procedure using two different sources has been demonstrated to prepare heteroatoms doped reduced graphene oxide such as nitrogen-doped reduced graphene oxide (N-RGO) and sulfur-doped reduced graphene oxide (S-RGO). The N-RGO has been hydrothermally synthesized using urea as nitrogen precursor, wherein the S-RGO has been synthesized using dimethyl sulfoxide (DMSO) as sulfur precursor. The successful N-doping, S-doping and other physicochemical properties of N-RGO and S-RGO have been confirmed with different spectroscopic and electrochemical techniques. The results indicated that doping into the graphene structure exhibits a high conductivity and a better transfer of charge. Moreover, heteroatoms doped graphene (N-RGO and S-RGO) and graphene-related materials (RGO) have been applied for the individual detection of uric acid (UA). Interestingly, the N-RGO exhibited a lower limit of detection (LOD, S/N = 3) of 2.7 10– 5 M for UA (10–1000 μM) compared with undoped RGO and S-RGO. Furthermore, the simultaneous detection of UA in the presence of Xanthine (XA) has been demonstrated a wide linear range of detection for UA: 10–1000 μM, with unchanged concentration of XA to be 200 μM, and exhibited a low limit of detection of 8.7 10− 5 M ( S∕N = 3) for UA. This modified sensor based on N-RGO has revealed a high selectivity and reproducibility thanks to its large surface area, high catalytic properties, and chemical structure. Indeed, the practical applicability of the proposed sensor has been evaluated in milk samples even in the presence of high concentrations of UA with satisfactory results.
5,500원
19.
2023.12
구독 인증기관 무료, 개인회원 유료
A glassy carbon electrode modified with a composite consisting of electrodeposited chitosan and carboxylated multi-walled carbon nanotubes (e-CS/MWCNTs/GCE) was used as a working electrode for simultaneous determination of dopamine (DA), serotonin (5-HT) and melatonin (MT), which were related to circadian rhythms. The electrochemical characterizations of the working electrode were carried out via electrochemical impedance spectroscopy and chronocoulometry. It was found that electrochemical modification method, that was cyclic voltammetry, may can cause continuous CS polymerization on MWCNTs surface to form a dense membrane with more active sites on the electrode, and the electrochemically active surface area of e-CS/MWCNTs/GCE obtained was about 7 times that of GCE. The electrochemical behaviour of DA, 5-HT and MT on working electrode were carried out via differential pulse voltammetry and cyclic voltammetry. The results showed that e-CS/MWCNTs/GCE solved the problem that the bare electrode could not detect three substances simultaneously, and can catalyze oxidation potential difference as low as 0.17 V of two substances reaction at the same time, indicating very good electrocatalytic activity. By optimizing the detection conditions, the sensor showed a good linear response to DA, 5-HT and MT in the range of 20-1000 μmol/L, 9-1000 μmol/L and 20-1000 μmol/L, and the detection limits were 12 μmol/L, 10 μmol/L and 22 μmol/L (S/N = 3), respectively. In addition, the proposed sensor was successfully applied to the simultaneous detection of DA, 5-HT and MT in human saliva samples.
4,200원
20.
2023.12
구독 인증기관·개인회원 무료
1
2
