간행물
Carbon Letters KCI 등재 Carbon letters
- 발행기관 한국탄소학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1976-4251 (Print)2233-4998 (Online)
- 수록기간 2000 ~ 2024
- 주제분류 자연과학 > 자연과학일반 자연과학 분류의 다른 간행물
- 십진분류KDC 530DDC 620
권호리스트/논문검색
Vol.6 No.3 (2005년 9월) 6건
1.
2005.09
구독 인증기관 무료, 개인회원 유료
The carbon sample "O", phosphoric acid-activated carbon "OP", zinc chloride-activated carbon "OZ", and two steam activated carbons "OS" and "OS2" with different burn-off of 25% and 58% respectively, were prepared from olive stones. The textural properties were determined from the results of nitrogen adsorption at 77 K and by analyzing these results through the application of different adsorption models. The chemistry of the carbon surfaces was determined from the base neutralization capacities, acid neutralization capacity and surface pH. The sorption of Pb2+ ions on to the carbons prepared was followed under dynamic and equilibrium conditions. The differences between the values of the textural parameters were attributed to the inapplicability of some adsorption models and to the heterogeneity of the microporous carbons. The sorption of Pb2+ ions is favored on carbon and activated carbons. However, chemically activated carbons are more effective compared with steam-activated ones. The sorption of Pb2+ ions were related to the chemistry of the surface rather than to the textural properties.
4,000원
2.
2005.09
구독 인증기관 무료, 개인회원 유료
Carbon/Carbon Composites due to their far superior thermo-mechanical properties are used in a number of demanding applications. However, the material still is used only in specific high tech applications with few exceptions in general industrial applications. The material is extremely expensive and the major challenge is to reduce its cost. Various innovative processing routes are outlined to reduce the cost of processing.
4,000원
3.
2005.09
구독 인증기관 무료, 개인회원 유료
Amit Saxena, Abha Sharma, Beer Singh, Malladi Venkata Satya Suryanarayana, Timir Haran Mahato, Mamta Sharma, Rajendra Prasad Semwal, Arvind Kumar Gupta, Krishnamurthy Sekhar
Room temperature kinetics of degradation of nerve agent simulants and sarin, an actual nerve agent at the surface of different carbon based adsorbent materials such as active carbon grade 80 CTC, modified whetlerite containing 2.0 and 4.0 % NaOH, active carbon with 4.0 % NaOH, active carbon with 10.0 % Cu (II) ethylenediamine and active carbon with 10.0 % Cu (II) 1,1,1,5,5,5-hexafluoroacetylacetonate were studied. The used adsorbent materials were characterized for surface area and micropore volume by N2 BET. For degradation studies solution of simulants of nerve agent such as dimethyl methylphosphonate (DMMP), diethyl chlorophosphate (DEClP), diethyl cyanophosphate (DECnP) and nerve agent, i.e., sarin in chloroform were prepared and used for the uniform adsorption on the adsorbent systems using their incipient volume at room temperature. Degradation kinetics was monitored by GC/FID and was found to be following pseudo first order reaction. Kinetics parameters such as rate constant and half life were calculated. Half life of degradation with modified whetlerite (MWh/NaOH) system having 4.0 % NaOH was found to be 1.5, 7.9, 1206 and 20 minutes for DECnP, DEClP, DMMP and sarin respectively. MWh/NaOH system showed maximum degradation of simulants of nerve agents and sarin to their hydrolysis products. The reaction products were characterized using NMR technique. MWh/NaOH adsorbent was also found to be active against sulphur mustard.
4,000원
4.
2005.09
구독 인증기관 무료, 개인회원 유료
The objective of this study was to investigate the possibility of application for water treatment using the zeocarbon. The zeocarbon was mixture of zeolite and activated carbon. In general, the application of commercial zeocarbon to water treatment is difficult because of weak strength in water and the high pH value of effluents after water treatment. Therefore, we have modified the surface of zeocarbon. For the surface modification, we used the acid treatment to make surface functional group. As a result of modification, was created functional group on zeocarbon surface and was formed mesopore in zeocarbon. The surface modified zeocarbon was applied to removal of nitrogen. In removal experiments of nitrogen, removal efficiency was very high. And, strength of zeocarbon after water treatment and pH of effluents were stabilized. This indicates that the surface modified zeocarbon was easy to recover and reuse. Consequently, our results were shown the possibility of application for water treatment using the surface modified zeocarbon.
4,000원
5.
2005.09
구독 인증기관 무료, 개인회원 유료
In this study, AR (aromatic resin) pitch was employed as the matrix-precursor for carbon/carbon composite because it exhibits much higher coke yield than coal tar pitch. As a result, a fabrication process of carbon/carbon composites can be shortened. It has been known that the pitches may cause swolling problem during the carbonization process. In order to restrain the swelling occurrence, a small quantity of carbon black was added to the AR pitch. Due to addition of carbon black the swelling was decreased largely and the perform can be infiltrated with the AR pitch. The densification efficiency of the performs was compared with various matrix-precursors. The coke yield of matrixprecursors, the morphology and the degree of graphitization of carbon matrix were analyzed.
4,000원
6.
2005.09
구독 인증기관 무료, 개인회원 유료
Jong-Min Choi, Tae-Jin Kim, Min-Soo Hyun, Dong-Hyun Peck, Sang-Kyung Kim, Byung-Rok Lee, Jong-Soo Park, Doo-Hwan Jung
Bipolar plates require some specific properties such as electrical conductivity, mechanical strength, chemical stability, and low permeability for the fuel cell application. This study investigated the effects of carbon nanotube (CNT) contents and process conditions of hot press molding on the electrical and physical properties using CNT 3~7 wt% added graphite nano-composites in the curing temperatures range of 140~200℃ and pressure of 200~300 kg/cm2. Bulk density, hardness and flexural strength increased with increasing CNT contents, curing pressure and temperature. With the 7 wt% CNT added noncomposite, the electrical resistance improved by 30% and the flexural strength increased by 25% as compared to that without CNT at the temperature of 160℃ and pressure of 300 kg/cm2. These properties were close to the DOE reference criteria as bulk resistance of 13 mΩcm and tensile strength of 515 kg/cm2.
4,000원
