PURPOSES: The purpose of this study is to provide the method of how to measure the coefficient of thermal expansion of concrete using temperature compensation principle of electrical resistance strain gauge. METHODS : The gauge factor compensation method and thermal output(temperature-induced apparent strain) correction method of selftemperature compensation gauge were investigated. From the literature review, coefficient of thermal expansion measurement method based on the thermal output differential comparison between reference material(invar) and unknown material(concrete) was suggested. RESULTS: Thermal output is caused by two reasons; first the electrical resistivity of the grid conductor is changed by temperature variation and the second contribution is due to the differential thermal expansion between gauge and the test material. Invar was selected as a reference material and it、s coefficient of thermal expansion was measured as 2.12×10-6m/m/℃. by KS M ISO 11359-2. The reliability of the suggested measurement method was evaluated by the thermal output measurement of invar and mild steel. Finally coefficient of thermal expansion of concrete material for pavement was successfully measured as 15.45×10-6m/m/℃. CONCLUSIONS: The coefficient of thermal expansion measurement method using thermal output differential between invar and unknown concrete material was evaluated by theoretical and experimental aspects. Based on the test results, the proposed method is considered to be reasonable to apply for coefficient of thermal expansion measurement.

The electrical properties of a laminated SMD type PTC thermistor for microcircuit protection were investigated as a function of polymer blowing agent addition. Green ceramics for multilayered BaTiO3-based PTCRs were formed by doctor blade method of barium titanate powders; we successfully laminated the sintered ceramic chips to obtain 10 layer chip PTCRs with PTC effect. The sintered density increases with increasing sintering temperature. The electrical properties of the sintered samples were strongly dependent on the calcination and addition of a polymer blowing agent. When BaTiO3 powders containing 0.2 mol% of Y2O3 were calcined at 1000˚C for 2 hrs, the resistivity jump was of 1-2 orders of magnitude. The resistivity at room temperature increases according to the polymer blowing agent addition. Also, the sample using the calcined powder showed a lower resistivity than that of the sample prepared using powders without calcinations. With an increase in the OBSH, the magnitude of the resistivity jumped as a function of the temperature increase. The resistivity of the sintered bodies after the addition of 0.5 wt% polymer blowing agent at 1290˚C for 2 h was shown to be about 8.5Ω·cm; the jump order of the sintered bodies was shown to be on the order of 102.

본 연구의 목적은 2002년과 2003년에 심각한 도시침수 피해를 받은 삼척지역을 대상으로 유역유출모형, 제내지 모형 그리고 하수도 시스템을 통합한 도시범람모형의 개발 및 적용한 것이다. 이를 위해 하도의 1차원 모형, 시가지의 표면류의 2차원 모형, 그리고 하수도 시스템을 상호 연결하는 방안을 제시하였다. 침수모형의 입력자료 구축에 필요한 표고 및 건물의 점유율과 같은 지형정보는 입력자료의 변환과정에서 발생할 수 있는 불확실한 오차를 줄이기 위해 수치

강구조물의 고력볼트 마찰접합부에 있어서 마찰면의 부식은 장기적으로 마찰력 감소와 접합부 내력저하를 초래한다. 본 연구는 고력볼트 접합부의 부식을 방지하고 소요 역학적 성질을 만족시키기 위해 접합부의 마찰면에 Zn/Al 금속용사 방청처리 한 고력볼트 접합부를 대상으로 마찰면의 표면처리방법과 피막두께를 주요 변수로 하여 인장시험을 실시하였고, 실험으로 부터 마찰면 표면거칠기와 미끄럼계수를 측정하였다. 무도장 샌드블라스트 처리한 접합부 및 샌드블라스트 처리 후 금속용사를 실시한 볼트 접합부의 미끄럼 계수는 국내 규준의 규정 값과 비교하여 동등 이상의 우수한 미끄럼계수 값을 나타냈다.